The basic steps to open your bonnet

Most cars have two release mechanisms: one inside the cabin and one under the bonnet itself. To open the bonnet, first locate the interior release lever, usually found on the left side of the dashboard or on the driver's side panel below the steering wheel. Pull this lever toward you — you will hear a click as the bonnet latch disengages.

Next, go to the front of your car and locate the secondary release, a small lever or button mounted on the underside of the bonnet near the center. Push or pull this release (depending on your car's design) and the bonnet will lift open. Some newer vehicles use a button on the dashboard instead of a manual under-bonnet release, so check your owner's manual if you do not find a lever underneath.

Once the bonnet is open, look for a prop rod or hydraulic strut on either side. Insert the rod into the slot above the bonnet to hold it safely in place while you work. If your car has hydraulic struts instead, they will hold the bonnet open automatically — do not force it if it feels stuck.

Key Takeaways

  • The interior release lever is usually on the left side of the dashboard or driver's side panel, and pulling it disengages the main latch.
  • After pulling the interior lever, you must push or pull the secondary release under the bonnet itself before it will fully open.
  • Always use the prop rod or check that hydraulic struts are holding the bonnet safely before you lean in or work underneath.
  • If you cannot find the interior lever or secondary release, your owner's manual shows the exact location for your specific model.

Where the interior release lever is located

The interior lever varies by manufacturer and model year. In most cars, it is mounted on the left side of the dashboard, below the steering wheel, or on the driver's side panel near the door. Some vehicles place it further to the left, near the floor. Look for a lever with a bonnet or engine symbol on it — this symbol is the universal indicator for the bonnet release.

If you cannot locate it by sight, run your hand along the left side of the dashboard and the panel below the steering wheel. You are looking for something you can grip and pull toward you. Pulling the lever should produce an audible click, which signals that the main latch has released. If nothing clicks, try the other side of the dashboard or consult your owner's manual for your exact model.

The secondary release under the bonnet

After you pull the interior lever, the bonnet will not open fully — it will only pop up slightly. This is by design. You must now reach under the bonnet near the center and locate the secondary release mechanism. This is usually a small lever, button, or hook that you push upward or pull toward you.

The secondary release prevents the bonnet from flying open while you are driving. Once you have pulled the interior lever and the bonnet has popped, slide your hand under the gap and feel for this mechanism. Push or pull it (your owner's manual will specify which direction for your car), and the bonnet will lift freely. Do not force it — if it feels stuck, you may not have fully released the interior lever.

Using the prop rod or hydraulic struts

Once the bonnet is open, you need to find it so it does not fall on your head or hands while you work. Most cars have a prop rod — a metal stick stored in a clip on the inside of the bonnet or on the engine bay wall. Remove this rod and insert one end into the slot or bracket above the bonnet opening. The rod will hold the bonnet at a safe working height.

Some newer cars use hydraulic struts instead of a prop rod. These are gas-filled cylinders on either side of the bonnet that hold it open automatically. If your car has struts, the bonnet will stay up on its own — do not try to prop it with a rod as well. If the bonnet feels heavy or starts to close, the struts may be worn and you should have them checked before working under the bonnet.

What to do if the bonnet will not open

If the interior lever pulls but nothing happens, the cable connecting the lever to the latch may be broken or disconnected. Try pulling the lever several times firmly — sometimes a stuck cable will free up. If the bonnet still does not pop, you may need to access the latch from underneath the car or have a mechanic release it.

If the bonnet pops but the secondary release will not budge, the latch mechanism itself may be frozen or corroded. Spray a penetrating oil like WD-40 around the secondary release and wait a few minutes, then try again. Do not force it, as you risk breaking the release mechanism. If it remains stuck, a mechanic can disassemble the latch or cut the bonnet open if necessary.

Closing the bonnet safely

Before you close the bonnet, remove the prop rod and store it back in its clip. Make sure nothing is resting on the engine or in the engine bay — tools, rags, and hoses can be damaged or cause fires if left inside. Lower the bonnet gently until it is about six inches from closed, then let it drop the rest of the way. It should latch with a solid click.

If the bonnet does not latch, it may not be aligned properly. Lift it again and check that the latch mechanism is clean and free of debris. Close it again more firmly. If it still will not latch, the latch or hinges may be bent and you should have it inspected by a mechanic before driving.

Frequently Asked Questions

What if I cannot find the interior release lever?

Check your owner's manual — it will show the exact location for your model. The lever is always inside the cabin, usually on the left side of the dashboard or driver's side panel. If you have a newer car, it may be a button on the dashboard instead of a pull lever.

Can I open the bonnet from outside the car?

No. You must pull the interior release lever first. The secondary release under the bonnet is only accessible after the interior lever has disengaged the main latch and the bonnet has popped open slightly.

Is it safe to work under the bonnet without the prop rod?

No. Always find the bonnet with the prop rod or verify that hydraulic struts are holding it open. A falling bonnet can cause serious injury. Never rely on your hand or another object to hold it up.

What does it mean if the interior lever feels loose or pulls all the way in?

The cable connecting the lever to the latch may be broken or disconnected. If pulling the lever produces no click and the bonnet does not pop, the cable has likely snapped and you will need a mechanic to repair or replace it.

How hard should I pull the interior release lever?

Pull firmly but do not yank. A normal pull should produce an audible click. If nothing happens after a firm pull, try again — sometimes the cable is sticky. If it still does not work after two or three attempts, stop and consult a mechanic.