Adjust your mirrors before you drive, not while moving

Side view mirrors need to show the road behind you and to the sides of your vehicle, with minimal blind spots. The goal is to position each mirror so you can see the edge of your car's body on the inner edge of the mirror, then expand outward to capture the lane beside you and the road behind. Most vehicles let you adjust mirrors from inside the cabin using a small lever or electronic controls, taking less than two minutes per side.

Proper mirror adjustment is a safety task, not a preference. A poorly angled mirror can hide an entire vehicle in your blind spot, making lane changes and merging dangerous. The adjustment method depends on whether your mirrors have manual controls (a lever you push) or power controls (buttons on the door panel), but the final position is the same.

Key Takeaways

  • Adjust mirrors while parked by positioning each one to show the edge of your car's body on the inner third of the mirror, then the lane beside you and road behind.
  • Manual mirrors use a lever on the door panel or mirror housing; power mirrors use buttons on the driver's door that let you select left or right mirror before adjusting.
  • The driver's side mirror should angle slightly downward and outward; the passenger side should angle more outward to cover the larger blind spot on that side.
  • Check your mirrors every time you get in the vehicle, because even small shifts from bumps or parking can change the angle and create blind spots.

Locate your mirror controls

Manual mirrors have a small lever or paddle attached directly to the back of the mirror housing or mounted on the door panel near the mirror. Push or pull this lever in the direction you want the mirror to move — up, down, left, or right. The lever controls both the tilt and the side-to-side angle at once.

Power mirrors use a small joystick or rocker switch, usually located on the driver's door panel to the left of the steering wheel. Look for a symbol showing a mirror with arrows. First, press the left or right side of the switch to select which mirror you are adjusting (driver or passenger), then use the joystick to move the mirror in any direction. Some vehicles have separate up-down and left-right controls instead of a joystick.

Position the driver's side mirror

Start with the driver's side mirror. Sit in the driver's seat in your normal driving position and look at the mirror. You should see the edge of your car's body — the rear quarter panel — taking up roughly the inner third of the mirror. This gives you a reference point and ensures the mirror is angled outward rather than backward.

From there, adjust the mirror so you can see the lane beside your vehicle and the road behind it. The mirror should show mostly road and traffic, not the side of your own car. Tilt it slightly downward so the horizon line (where the road meets the sky) sits in the upper third of the mirror. This angle helps you see vehicles in your blind spot when you glance over.

Position the passenger's side mirror

The passenger side has a larger blind spot than the driver side because of the vehicle's shape and your seating position. Adjust this mirror more aggressively outward than the driver's side. You should see very little of your own car's body — just a sliver on the inner edge — and mostly the lane beside you and the road behind.

Angle the passenger mirror slightly downward as well, using the same horizon-in-the-upper-third rule. Because this mirror points more outward, it will feel like you are looking at a wider, more distant view. That is correct. The goal is to eliminate the blind spot that exists on the passenger side when you are changing lanes or merging to the right.

Test your adjustment before driving

Before you leave the parking spot, perform a quick blind spot check. Turn your head to look over your shoulder toward the driver's side, then glance at the driver's mirror. You should see the same vehicle or road section in both your direct view and the mirror — this overlap confirms the mirror is not hiding anything. Repeat this test on the passenger side.

If you see a vehicle in the mirror that disappears when you turn your head, the mirror is angled too far inward and is showing you the side of your own car instead of the road. Adjust it outward slightly and test again. If you turn your head and see a vehicle that was not visible in the mirror, the mirror is angled too far outward — adjust it inward a bit.

Adjust mirrors again if they shift

Mirrors can move slightly from bumps, potholes, or contact while parking. Before every drive, take five seconds to glance at each mirror and confirm it still shows the lane beside you and the road behind. If a mirror has shifted, use the same adjustment process to reposition it. This habit prevents you from driving with a hidden blind spot.

If your mirrors shift frequently, check whether the adjustment lever or power motor is loose. A lever that feels sloppy or a motor that does not hold position may indicate a mechanical problem. Have a technician inspect the mirror mounting and adjustment mechanism if this happens.

Frequently Asked Questions

Should I be able to see the side of my car in the mirror?

Yes, but only a small sliver on the inner edge. If you see more than the rear quarter panel, the mirror is angled too far inward. Adjust it outward so you see mostly road and traffic, with just a thin line of your car's body as a reference point.

Why does the passenger mirror need to angle more outward than the driver's?

The passenger side has a larger blind spot because you sit on the left side of the vehicle. Angling the passenger mirror more outward helps you see vehicles in that blind spot when you glance over before changing lanes to the right.

What if my power mirrors do not respond to the buttons?

Check that the mirror select switch is set to the correct side (left or right). If the buttons still do not work, the power motor may be faulty. Have a technician test the electrical connection and motor. In the meantime, you can use manual adjustment if your vehicle has a backup lever on the mirror housing.

Do I need to adjust mirrors differently for towing a trailer?

Yes. When towing, extend your mirrors outward more than usual so you can see the sides of the trailer and the road behind it. Some vehicles have extendable mirror arms for this purpose. Adjust them back to normal driving position once you unhitch the trailer.

How often should I check my mirror adjustment?

Check before every drive. Mirrors shift from bumps and parking, and even a small angle change can create a blind spot. It takes five seconds and can prevent a collision.