Adjust mirrors before you leave the rental lot, not while driving
U-Haul rental trucks have larger mirrors than your car, and they sit higher and farther out. If you do not adjust them to your sight lines, you will have blind spots that can hide other vehicles, pedestrians, or obstacles. The adjustment takes five minutes and uses the same hand controls you would find on any truck—but the wider field of view means the angles matter more.
Most U-Haul trucks use manual mirror adjustment, which means you reach out the window or use a hand crank to move them. Some newer models have electric controls on the door panel. Either way, the goal is the same: position each mirror so you can see the road behind you and to the side without turning your head, and so the truck's body is barely visible in the mirror itself.
Key Takeaways
- Adjust both side mirrors before leaving the lot so you can see the lane behind you and beside you without blind spots.
- Position each mirror so the truck's body takes up only a small sliver on the inner edge, and the road behind fills most of the mirror.
- Manual mirrors require you to reach out the window or use a hand crank; electric mirrors use a rocker switch on the door panel.
- Check your mirrors again after loading cargo, because weight distribution can change how the truck sits and shift your sight lines.
How to adjust manual side mirrors
Manual mirrors on U-Haul trucks are adjusted by hand. Sit in the driver's seat, roll down your window, and reach out to the mirror housing. You will feel the mirror glass itself—it pivots on a ball joint or hinge. Push and pull the glass to move it up, down, left, or right until you reach the angle you want.
Start with the driver's side mirror. Angle it so you can see the road behind the truck and one lane to the left. The truck's body should occupy only the inner 10 to 15 percent of the mirror; the rest should be road. Then do the same for the passenger mirror, angling it to show the road behind and one lane to the right. If you cannot see the truck's body at all, you have angled it too far outward—bring it back in slightly.
Some U-Haul trucks use a hand crank instead of direct hand adjustment. Look for a small handle on the inside of the mirror housing. Turn it clockwise or counterclockwise to move the mirror. The direction varies by truck model, so turn slowly and watch the mirror move until you find the right angle.
How to adjust electric mirrors
Newer U-Haul trucks and some premium rentals have electric mirror controls on the driver's door panel. Look for a small rocker switch or joystick labeled with arrows or a mirror symbol. This switch controls both mirrors, but you have to select which one you are adjusting first.
Most electric mirror controls have a small button or toggle that lets you choose the driver's side or passenger's side mirror. Press or toggle to select the driver's mirror, then use the rocker switch to move it. Push the switch up to tilt the mirror up, down to tilt it down, left to angle it left, and right to angle it right. Once the driver's mirror is set, switch to the passenger mirror and repeat. The adjustment is the same as manual: truck body barely visible on the inner edge, road filling the rest of the mirror.
Why mirror position matters in a rental truck
A U-Haul truck is wider and taller than a standard car, and the mirrors are positioned farther from your eyes. That distance changes what you can see. A mirror angle that works for your car will leave blind spots in a truck because the geometry is different. Vehicles in the lane beside you or slightly behind can disappear into the space between your side mirror and your peripheral vision.
Proper mirror adjustment does not eliminate all blind spots—no mirror setup does—but it shrinks them significantly. When you can see the road behind and beside you in both mirrors without turning your head, you have reduced the risk of changing lanes into another vehicle or missing a pedestrian at an intersection. This is especially important in a rental truck because you are not used to its size and handling.
Adjust mirrors again after loading cargo
If you are renting a U-Haul to move furniture or boxes, the truck's weight distribution changes as you load it. A heavily loaded truck may sit lower in the back, which tilts the mirrors slightly and changes your sight lines. Before you drive away from the loading point, sit in the driver's seat and check both mirrors again.
You do not need to make large adjustments—usually just a small tilt up or down to restore your view of the road. But skipping this step is a common reason renters end up with unexpected blind spots during the drive. Spend 30 seconds checking and adjusting if needed; it takes far less time than dealing with a collision or a near-miss.
Check your mirrors at every stop
As you drive, vibration and road conditions can shift your mirrors slightly out of position. If you notice that you cannot see the road clearly in one mirror, or that the truck's body is taking up too much of the view, pull over safely and adjust it again. This is especially true on long drives or rough roads.
Make mirror checks part of your routine at gas stops or rest breaks. A 10-second visual check—can you see the road behind and beside you?—takes almost no time and keeps your sight lines sharp for the next leg of the drive.
Frequently Asked Questions
Can I adjust the mirrors while driving?
You should not. Adjusting mirrors while moving your eyes away from the road increases the risk of missing hazards. Pull over in a safe location, make your adjustment, and verify your sight lines before driving again.
What if the mirror glass is cracked or loose?
Report it to the U-Haul rental agent before you leave the lot. A damaged mirror is a safety issue and a liability issue. The rental company will either repair it or swap the truck for another one. Do not attempt to drive with a cracked or unstable mirror.
Do I need to adjust mirrors differently for towing a trailer?
Yes. If your U-Haul rental includes a trailer, the trailer will be wider than the truck bed, and you will need to angle the mirrors outward more to see around it. Adjust them so you can see the sides of the trailer in your mirrors, not just the truck. This is especially important when changing lanes.
Why can't I see the truck's body in my mirror at all?
If the mirror is angled too far outward, you lose the reference point that helps you judge distance and position. Bring it back in until you can see a small sliver of the truck's body on the inner edge of the mirror. This gives you depth perception and helps you stay centered in your lane.
Should I adjust mirrors the same way in a U-Haul van versus a truck?
The principle is the same, but the geometry differs. Vans have mirrors mounted lower and closer to the driver's eyes than trucks do. Start with the same setup—truck body barely visible, road filling the mirror—and then fine-tune based on what you actually see when you sit in the driver's seat.