Jumper cables let you borrow power from another car's battery to start your own
When your battery is too weak to turn the engine over, jumper cables create a temporary electrical path between a working battery and yours. One end of each cable clamps to the dead battery, the other end clamps to the working battery in another car. The working battery pushes current through the cables into your battery, giving it enough power to crank the engine. Once your engine runs, your alternator takes over and recharges your battery while you drive.
The process takes about five minutes of setup and another minute or two of cranking. You need a second vehicle with a working battery, a set of jumper cables, and both cars parked close enough that the cables reach between them—usually within three to four feet.
Key Takeaways
- Always connect the red cable to the positive terminal of the dead battery first, then to the positive terminal of the working battery.
- Connect the black cable to the negative terminal of the working battery, then to an unpainted metal surface on your engine block—never directly to the dead battery's negative terminal.
- Start the working car and let it run for two to three minutes before attempting to start your car.
- Remove the cables in reverse order: black from your car, black from the working car, red from the working car, red from your car.
- Drive your car for at least 20 minutes after a successful jump to let the alternator recharge the battery.
What you need before you start
You need a set of jumper cables at least 10 feet long—longer cables give you more flexibility in positioning the cars. Cables come in different gauges; thicker cables (4 or 2 gauge) work better than thin ones (8 gauge), especially in cold weather. The clamps on each end should grip the battery terminals firmly without slipping.
You also need a second vehicle with a battery in working condition. The working car's battery does not have to be the same size as yours, but it should be at least as powerful. A car battery is typically 12 volts; if you are jumping a truck or large SUV with a smaller car, it will take longer but still works. Do not attempt to jump a 24-volt truck battery (some commercial vehicles) with a 12-volt car battery—you will damage both.
Make sure both cars are parked on level ground with the engines off. Turn off all electrical loads in both vehicles: headlights, radio, climate control, and interior lights. This reduces the strain on both batteries during the jump.
Position the cars and prepare the batteries
Park the working car close enough that the jumper cables reach both batteries comfortably—usually three to four feet apart. Do not let the cars touch. Open both hoods and locate the battery terminals. The positive terminal is marked with a plus sign (+) or a red cover; the negative terminal is marked with a minus sign (−) or a black cover.
If the battery terminals are corroded (white, blue, or green crusty buildup), clean them with a wire brush or an old toothbrush before connecting the cables. Corrosion blocks electrical flow and can prevent the jump from working. If the terminals are very corroded, you may need to scrape with a small tool, but be careful not to crack the battery case.
Check that the battery case itself is not cracked or leaking. If you see fluid leaking from the battery, do not attempt a jump—the battery is damaged and jumping it can cause a fire or explosion. Call a tow truck instead.
Connect the red cable first
Take the red (positive) cable and clamp one end firmly to the positive terminal of your dead battery. The clamp should grip the terminal post tightly; if it is loose, it will not make good electrical contact and the jump will not work. You should hear a slight click as the clamp seats.
Take the other end of the red cable and clamp it to the positive terminal of the working battery. Again, make sure the clamp is tight and fully seated on the terminal. At this point, you have created a positive electrical path between the two batteries.
Connect the black cable to complete the circuit
Take the black (negative) cable and clamp one end to the negative terminal of the working battery. This is the second car's battery, not yours. Make sure the clamp is tight.
Take the other end of the black cable and clamp it to an unpainted metal surface on your engine block—not to the negative terminal of your dead battery. Look for a bolt, bracket, or bare metal surface on the engine itself, away from the battery. This is the critical step that prevents sparks near the battery. If you connect the black cable directly to your battery's negative terminal, a spark can ignite hydrogen gas that batteries release, causing an explosion.
Double-check all four clamp connections: red to your positive, red to their positive, black to their negative, black to your engine. All four should be tight and make solid contact.
Start the working car and wait
Start the engine of the working car and let it run for two to three minutes. This gives the working battery time to push current through the cables into your battery. You do not need to rev the engine; just let it idle normally.
After two to three minutes, attempt to start your car. Turn the key or press the start button as you normally would. If the engine cranks but does not start, wait another minute and try again. If the engine does not crank at all, the battery may be too far gone or the cables may not be making good contact—check all four clamps again.
If your car starts, let it run for a few seconds to confirm it is running steadily, then move on to removing the cables.
Remove the cables in the correct order
Removing the cables in the wrong order can damage the alternator or create a spark. Always remove them in this exact sequence: black from your car, black from the working car, red from the working car, red from your car.
Start by unclipping the black cable from the unpainted metal surface on your engine. Then unclip the black cable from the negative terminal of the working battery. Next, unclip the red cable from the positive terminal of the working battery. Finally, unclip the red cable from the positive terminal of your battery. Coil the cables loosely and store them in the working car.
Do not turn off your engine yet. Keep your car running and thank the other driver for their help.
Drive your car to recharge the battery
Drive your car for at least 20 to 30 minutes at normal highway or city speeds. Your alternator generates electricity while the engine runs, and this electricity recharges the battery. Short trips around the block are not enough; the battery needs sustained charging time to recover fully.
If your car dies again within a few hours or days, the battery is likely at the end of its life and needs replacement. A healthy battery should hold a charge for weeks even if the car sits unused. If you had to jump it because you left the lights on or the car sat unused for months, one jump may be enough. If the battery failed for no obvious reason, plan to have it tested or replaced soon.
Frequently Asked Questions
What if my car still won't start after jumping it?
Check that all four cable clamps are tight and making solid contact with the terminals. Corrosion or loose clamps are the most common reason jumps fail. If the clamps are tight and the battery terminals are clean, the battery may be too damaged to jump, or the problem may not be the battery at all—it could be a bad starter motor or a fuel system issue. Call a tow truck.
Can I jump-start my car alone without another vehicle?
No. Jumper cables require a second battery with enough power to push current into yours. A portable jump starter (a battery pack you charge at home) can work if you have one, but a second vehicle is the standard method. If you do not have access to another car, call a tow truck or roadside information service.
Is it safe to jump a battery in the rain?
It is safer to wait if possible, but jumping in light rain is generally acceptable if you keep the battery terminals dry. Heavy rain or standing water increases the risk of electrical shock. If a storm is severe, wait it out or call for a tow. Never jump a battery during lightning.
How long should I let the working car run before I try to start mine?
Two to three minutes is usually enough for the working battery to push sufficient current into your battery. In very cold weather, wait three to five minutes. If your car does not start after that, wait another minute and try again rather than cranking repeatedly, which drains both batteries.
What does it mean if my battery keeps dying even after a successful jump?
A battery that dies repeatedly after a jump is likely failing and needs replacement. It could also mean your alternator is not charging the battery while the engine runs, which is a separate electrical problem. Have the battery tested at an auto parts store (many do this free) or take the car to a mechanic for diagnosis.