What happens when you replace an ignition lock cylinder
The ignition lock cylinder is the part that turns when you insert your key—it's a metal barrel that rotates inside the steering column to complete the electrical circuit that starts your engine. When it wears out, your key may stick, turn too easily, or fail to turn at all. Replacing it means removing the steering column cover, unbolting the old cylinder, and installing a new one coded to match your existing key.
This is a job you can do yourself if you're comfortable working inside the steering column, though it requires patience and the right tools. The alternative is taking it to a mechanic or dealership, which costs more but saves you time and the risk of damaging the column itself.
Key Takeaways
- The ignition lock cylinder is a replaceable part that sits inside your steering column and rotates when you turn your key.
- You'll need a new cylinder coded to your key, a screwdriver set, a steering wheel puller (if your wheel doesn't come off easily), and possibly a drill bit if the old cylinder is stuck.
- The job involves removing the steering wheel and column covers, unbolting the old cylinder, and sliding in the new one—typically 1 to 3 hours for a DIY job.
- If your key is broken or lost, you can order a new cylinder with a different key code, but you'll need to match it to your door locks or reprogram your vehicle's immobilizer.
- Dealerships can do this work and code the new cylinder to your vehicle's security system, but independent locksmiths often charge less.
Tools and parts you'll need before starting
Gather these items before you begin: a new ignition lock cylinder (ordered to match your key or with a key code you specify), a screwdriver set (Phillips and flathead), a socket set, a steering wheel puller if your wheel is tight, needle-nose pliers, and a flashlight. Some vehicles also need a small drill bit (around 1/8 inch) if the cylinder is seized or damaged.
The new cylinder itself is the biggest expense. A replacement from an aftermarket supplier costs between $15 and $50, while an OEM (original equipment manufacturer) part from your dealership runs $40 to $150 depending on your vehicle. If you're ordering it, specify whether you want it coded to your existing key or with a new key code. Most suppliers will send two keys with a new cylinder.
Check your vehicle's service manual for the exact tools needed for your model—some steering columns are easier to access than others, and a few vehicles require special removal tools you can rent or borrow.
Step-by-step removal and installation
Step 1: Disconnect the battery. Locate the negative terminal on your battery and disconnect it. This prevents accidental airbag deployment or electrical shorts while you're working inside the steering column. Wait a few minutes before proceeding.
Step 2: Remove the steering wheel. Turn the wheel to center it, then use a socket to remove the bolt in the center of the wheel (usually 15mm or 16mm). Once the bolt is out, use a steering wheel puller to gently separate the wheel from the column shaft. Disconnect the horn wire and any other connectors behind the wheel, then set the wheel aside.
Step 3: Remove the column covers. Most vehicles have a plastic shroud above and below the steering column. These are held by screws or clips. Remove them to expose the ignition cylinder housing. Take a photo with your phone before you start—it helps when reassembling.
Step 4: Locate and remove the cylinder retaining bolt. Look for a small bolt or pin on the side of the cylinder housing. This bolt holds the cylinder in place. Remove it with the appropriate socket or screwdriver. On some vehicles, you'll need to turn the key to the "On" position first to align the bolt hole.
Step 5: Extract the old cylinder. Gently pull the cylinder straight out of the housing. If it's stuck, do not force it—explore penetrating oil (like WD-40) and wait 15 minutes, then try again. If it still won't budge, you may need to carefully drill out the retaining pin, but this should be a last resort.
Step 6: Insert the new cylinder. Slide the new cylinder into the housing, making sure it seats fully. Insert and tighten the retaining bolt. Turn the key through all positions (Off, Accessory, On, Start) to confirm smooth operation before reassembling.
Step 7: Reassemble the column. Reinstall the column covers, reconnect the horn wire, and bolt the steering wheel back on. Reconnect the battery and test the ignition in all positions.
When to drill out a stuck cylinder
If the cylinder won't turn or come out after explore penetrating oil, you may have a broken key fragment inside or internal corrosion. Drilling is a last resort because it can damage the housing, making the new cylinder harder to install. Use a drill bit slightly smaller than the cylinder diameter and drill slowly through the center of the cylinder to break the internal pins.
Once drilled, the cylinder should come out more easily. Clean any debris from the housing before installing the new one. If you're not confident drilling, this is the point to stop and take the vehicle to a locksmith or mechanic—the cost of repair if you damage the column will exceed what you'd pay for professional help.
Matching the new cylinder to your vehicle's security system
If you ordered a new cylinder with a different key code than your original, you'll have a mismatch: your door locks and trunk will open with one key, but your ignition will need a different key. You have two options.
The first is to have a locksmith rekey your door locks and trunk to match the new ignition key. This costs $50 to $150 depending on how many locks need rekeying. The second is to order a new cylinder coded to your original key code, which costs more upfront but avoids the rekeying step.
If your vehicle has a transponder key (a key with a chip that communicates with the engine computer), the new cylinder itself doesn't need reprogramming—the key does. Most dealerships and locksmiths can program a new transponder key to your vehicle for $50 to $200. If you're keeping your original key, no programming is needed.
When to take it to a professional instead
Take your vehicle to a locksmith or dealership if the cylinder is severely corroded, if you're uncomfortable removing the steering wheel, or if your vehicle has an electronic steering lock that requires special tools. Dealerships charge $200 to $400 for the full job including parts and labor. Independent locksmiths often charge $100 to $250, and they can usually do the work while you wait.
A dealership has the advantage of access to your vehicle's security codes and can reprogram the new cylinder to your immobilizer system if needed. Independent locksmiths are faster and cheaper for straightforward replacements but may not have access to your vehicle's security system if reprogramming is required.
Frequently Asked Questions
Can I use my old key with a new cylinder?
Yes, if you order the new cylinder coded to your existing key code. When you purchase a replacement, tell the supplier your vehicle's year, make, and model, and ask for a cylinder coded to your current key. The supplier will match the internal pins to your key's cuts.
What if my key is broken inside the cylinder?
A broken key fragment will prevent the cylinder from turning. You'll need to drill out the cylinder to remove the fragment, then install a new one. A locksmith can do this quickly—it's not worth attempting if you're unsure, because drilling can damage the housing.
Do I need to reprogram anything after installing a new cylinder?
The cylinder itself doesn't need reprogramming. If you have a transponder key (a key with a chip), the key may need programming to your vehicle's computer, but this is separate from the cylinder replacement. If you're keeping your original key and it already works with your vehicle, no programming is needed.
How long does this job take?
A DIY replacement typically takes 1 to 3 hours, depending on how easily your steering wheel comes off and whether the old cylinder is stuck. A professional locksmith or mechanic can usually finish in 30 minutes to 1 hour.
What's the difference between a cylinder coded to my key and one with a new key code?
A cylinder coded to your key means the internal pins match your existing key's cuts, so your key will turn it. A cylinder with a new key code comes with two new keys that match it, but your old key won't work. If you choose a new code, you'll need to rekey your door locks or have a locksmith reprogram them to match.