What glow plugs do and why checking them matters
Glow plugs are heating elements that warm the combustion chamber in a diesel engine before it starts. When you turn the key, they glow red-hot for a few seconds, raising the temperature enough for diesel fuel to ignite on its own. Without them working, your diesel engine will crank but won't fire—especially in cold weather. A failed glow plug doesn't always stop the engine from starting, but it makes cold starts harder, slower, and rougher, and it puts extra strain on the starter motor and battery.
Checking glow plugs means testing whether they heat up when they should and whether they're still intact. You can do a basic visual inspection yourself, but a proper electrical test requires a multimeter and some mechanical knowledge. Most owners notice a problem when the engine hesitates on cold mornings or when the glow plug warning light stays on longer than usual.
Key Takeaways
- A glow plug warning light that stays on for more than a few seconds after starting, or comes back on while driving, signals that at least one plug has failed.
- You can visually inspect glow plugs by removing the valve cover and looking for corrosion, cracks, or loose connections, but electrical testing requires a multimeter.
- Testing individual glow plugs with a multimeter measures the resistance of each heating element; a reading outside the manufacturer's range means that plug is dead.
- Glow plugs typically last 80,000 to 100,000 miles, but cold climates and frequent short trips shorten their life.
- Replacing all glow plugs at once prevents the frustration of one failing shortly after you replace another.
Reading the glow plug warning light
The glow plug warning light on your dashboard looks like a coiled wire and usually glows amber or yellow. When you start a diesel engine, this light comes on for a few seconds while the plugs heat the combustion chamber, then goes out once the engine is warm enough to run on its own. If the light stays on for more than 10 to 15 seconds, or if it comes back on while you're driving, one or more plugs are not heating properly.
A persistent warning light does not always mean the engine won't start, but it does mean the plugs are failing. Cold starts will become harder and take longer. The engine may crank roughly or misfire until it warms up. Continuing to drive with failed glow plugs puts extra load on the starter and battery, which can shorten their life. The sooner you check the plugs, the sooner you can replace the bad ones before they leave you stranded.
Visual inspection: what to look for
Before you test electrically, you can look at the plugs themselves. Remove the valve cover or access panel on top of the engine—your owner's manual shows where it is. You'll see the glow plugs as thick wires or ceramic rods screwed into the cylinder head, usually with a wire connector on top of each one. Look for corrosion on the connector, cracks in the ceramic body, or loose wires that have come unplugged.
Corrosion on the connector is common and often the real problem: the plug itself is fine, but the electrical connection is broken. If you see white or blue-green crusty buildup on the connector, unplug it and clean both the connector and the terminal with a wire brush or fine sandpaper. Plug it back in firmly. If the ceramic part of the plug is cracked or the metal tip is pitted and black, that plug needs to be replaced. A loose connector is an straightforward fix—push it back on until it clicks.
Testing glow plugs with a multimeter
A proper electrical test tells you whether each plug is heating or not. You'll need a digital multimeter set to the resistance (ohms) setting. Consult your vehicle's service manual for the correct resistance range for your engine—this varies by manufacturer, but most diesel glow plugs read between 0.5 and 2 ohms when cold and working.
Disconnect the wire connector from the first glow plug. Touch one multimeter probe to the metal terminal on top of the plug and the other to a clean metal part of the engine block or cylinder head. The reading should fall within the range your manual specifies. If the reading is zero or very close to zero, the plug is shorted and must be replaced. If the reading is much higher than the range—5 ohms or more—the heating element has burned out. Test each plug the same way. Any plug outside the normal range is bad and should be replaced.
If you don't have a multimeter or are not comfortable using one, a mechanic can run this test in minutes. It's a straightforward job and usually costs less than $50 for the full set of plugs.
When to replace glow plugs
Glow plugs are a wear item, like spark plugs in a gasoline engine. Most last between 80,000 and 100,000 miles under normal driving. Cold climates, frequent short trips, and towing shorten their life because the engine spends more time cold and the plugs work harder. If you live somewhere with long winters or drive mostly in the city, your plugs may need replacing closer to 60,000 miles.
Replace all glow plugs at the same time, even if only one has failed. The others are the same age and will fail soon after. Replacing them one at a time means returning to the job repeatedly. A full set of glow plugs costs between $40 and $150 depending on the engine, and labor usually runs $200 to $400 at a shop. Doing it yourself saves the labor cost if you're comfortable removing and installing the plugs, but it requires the right socket and care not to crack the ceramic body.
Removing and installing new glow plugs
If you're replacing the plugs yourself, you'll need a glow plug socket (a deep socket with a rubber insert to grip the ceramic body), a ratchet, and new plugs matched to your engine. Disconnect the negative battery terminal first. Remove the wire connector from each plug by twisting gently or pressing the release tab, depending on the connector type. Use the glow plug socket to unscrew each plug—they're usually tight, so explore steady pressure and don't force it.
Before installing the new plugs, check that the threads in the cylinder head are clean and not damaged. Screw the new plug in by hand first to avoid cross-threading, then tighten it with the socket. Don't over-tighten; these plugs are fragile and the ceramic can crack. Reconnect the wire connectors firmly. Start the engine and check that the warning light goes out after a few seconds. If it stays on, one of the new plugs may be faulty or a connector may not be seated properly.
Troubleshooting a glow plug warning light that won't go away
If you've replaced the glow plugs and the warning light still stays on, the problem may not be the plugs themselves. Check that all wire connectors are pushed on firmly and that none are corroded. A loose or corroded connector will trigger the warning light even if the plugs are new. Clean the connectors with a wire brush and reseat them.
The glow plug relay or control module can also fail, preventing power from reaching the plugs even though they're working. If the connectors are clean and tight but the light persists, have a mechanic scan the engine computer for fault codes. The code will point to a specific plug, connector, or relay. A faulty relay is less common than a bad plug, but it's the next thing to check if the plugs themselves test fine.
Frequently Asked Questions
Can I drive with a failed glow plug?
Yes, but with difficulty. A single failed plug makes cold starts harder and slower, especially below freezing. The engine may crank for longer than usual or misfire until it warms up. Continuing to drive puts extra strain on the starter and battery. Replace the plug as soon as you can to avoid being stranded on a cold morning.
How long does it take to replace glow plugs?
At a shop, usually one to two hours for a full set. The time depends on engine design and how accessible the plugs are. Some engines have plugs that are straightforward to reach; others require removing intake manifolds or other components. If you're doing it yourself and have never done it before, budget three to four hours.
What's the difference between glow plugs and spark plugs?
Spark plugs ignite gasoline in a gasoline engine by creating an electrical spark. Glow plugs heat the combustion chamber in a diesel engine so the fuel ignites from compression alone. Diesel engines don't need spark plugs because diesel fuel ignites at a lower temperature than gasoline when compressed.
Why do glow plugs fail faster in winter?
Cold weather forces glow plugs to work harder and longer each time you start the engine. In freezing temperatures, the combustion chamber is much colder, so the plugs have to heat it more to reach ignition temperature. Repeated heavy use over a long winter wears out the heating element faster than mild-weather driving.
Can a bad glow plug damage the engine?
A single failed plug won't damage the engine, but it makes starting difficult and puts extra load on the starter motor and battery. If multiple plugs fail and you ignore the warning light for a long time, the repeated hard cranking can wear out the starter. Replace failed plugs promptly to avoid secondary damage.