A bad relay usually shows up as an electrical system that works intermittently or not at all

A relay is an electromagnetic switch that uses a small electrical signal to control a larger one. When a relay fails, the circuit it controls either stops working entirely or works only sometimes. The most common sign is a component that should be running—your fuel pump, cooling fan, starter, or headlights—either not working at all or working only when you tap on the relay or move the car.

The reason you notice this is that a relay sits between your battery and the component it powers. When the relay's internal contacts corrode, weld together, or the electromagnet inside stops responding, the power either never reaches the component or reaches it unpredictably. You can test a relay yourself with basic tools, and in most cases, a bad relay is a straightforward replacement.

Key Takeaways

  • A relay that is failing usually causes the component it controls to stop working, work only sometimes, or work only when you tap on the relay itself.
  • You can test a relay with a multimeter by checking for continuity across its contacts, or by swapping it with an identical relay from another circuit to see if the problem moves.
  • Relays are located in relay boxes under the hood or inside the cabin, and your owner's manual or a wiring diagram shows which relay controls which component.
  • A bad relay costs between $5 and $25 to replace, and the replacement itself usually takes less than five minutes once you locate the correct relay.
  • Some relay failures are caused by a short circuit or overload in the component the relay controls, so if a new relay fails quickly, the real problem may be elsewhere in that circuit.

What happens inside a relay when it fails

A relay has two circuits: a control circuit (the small signal) and a power circuit (the large current). Inside the relay case is a coil of wire that creates a magnetic field when current flows through the control circuit. That magnetic field pulls a metal arm, which closes contacts and completes the power circuit. When the control signal stops, a spring pushes the arm back and opens the contacts again.

When a relay fails, one of three things has usually happened. The contacts inside have corroded or oxidized, so they no longer conduct electricity reliably. The electromagnet coil has burned out or developed an open circuit, so the magnetic field never forms and the arm never moves. Or the contacts have welded together from heat or arcing, so they stay closed even when they should open, or they stick and only close when you physically vibrate the relay by tapping it.

Moisture, heat cycles, and electrical surges all accelerate relay failure. A relay that is mounted near the engine or in a damp location will fail sooner than one in a dry, cool spot. If the circuit the relay controls draws too much current—because the component is shorted or the wiring is damaged—the relay's contacts will arc and burn, shortening its life.

How to test a relay with a multimeter

Before you replace a relay, confirm that the relay itself is the problem and not the wiring, fuse, or component it controls. You will need a multimeter set to the resistance (ohms) setting, and you should remove the relay from its socket so you can test it outside the circuit.

First, locate the relay in your relay box. Your owner's manual or the diagram printed on the inside of the relay box cover will tell you which relay controls the circuit you are testing. Pull the relay straight out—it should come free with gentle pressure. Look at the relay terminals: most relays have four or five pins arranged in a specific pattern.

Set your multimeter to the ohms (resistance) setting. Touch the two probes to the two control circuit pins (usually pins 1 and 3, but check your relay's diagram). You should see a reading of around 50 to 150 ohms. If you see infinite resistance (the display shows "1" or "OL"), the coil is open and the relay is bad. If you see zero ohms, the coil is shorted and the relay is bad.

Next, touch the probes to the two power circuit pins (usually pins 2 and 5). With the relay unpowered, you should see infinite resistance—the contacts are open. If you see zero ohms or a low resistance reading, the contacts are welded shut and the relay is bad. Now, if you have a 12-volt power source available, you can explore power to the control pins and retest the power pins. When powered, the power pins should show near-zero resistance (the contacts close). When you remove power, they should return to infinite resistance. If they do not change, the relay is bad.

The swap test: a faster way to confirm a bad relay

If you do not have a multimeter or prefer a quicker check, you can swap the suspect relay with an identical relay from a different circuit that is working. Look at the relay box diagram and find another relay of the same type and part number. Pull both relays out and swap their positions.

Start the engine and test the circuit that was failing. If the problem moves to the circuit you just pulled the relay from, the original relay is bad. If the problem stays in the original circuit, the relay is probably not the cause—the issue is likely a blown fuse, a broken wire, a bad switch, or a failed component.

This test works because you are moving the suspected bad relay to a different circuit. If the relay is truly bad, it will fail in its new location too. If the problem stays behind, you know the relay was not the cause.

Where relays are located and how to find the right one

Most vehicles have two relay boxes: one under the hood near the battery or fuse panel, and one inside the cabin under the dashboard or behind a kick panel. Some vehicles have relays scattered throughout the engine bay as well. Your owner's manual will show you the location of each relay box and provide a diagram that labels every relay by function.

The diagram usually shows a grid with numbered or lettered positions, and each position is labeled with what that relay controls—fuel pump relay, cooling fan relay, starter relay, headlight relay, and so on. Write down the position number or letter of the relay you need to test, then open the relay box cover and locate that position. The relay itself is a small plastic block, usually black or tan, with four or five metal pins on the bottom.

If you have lost your owner's manual, you can find relay diagrams online by searching for your vehicle's year, make, and model plus "relay diagram" or "fuse box diagram." Many auto parts stores also keep printed diagrams on hand, and some will print one for you if you give them your vehicle's information.

What to do if the relay tests bad

Once you have confirmed the relay is bad, replacement is straightforward. Buy a replacement relay with the same part number as the original. You can find the part number printed on the relay itself, or you can take the old relay to an auto parts store and ask them to match it. Relays are inexpensive—most cost between $5 and $25.

To install the new relay, straightforward push it into the socket until it clicks or seats fully. The pins should slide into the socket smoothly; do not force it. Once the relay is seated, close the relay box cover and test the circuit. The component should now work normally.

If a new relay fails within a few weeks or months, the problem is likely not the relay itself but the circuit it controls. A short circuit, a failed component, or damaged wiring can cause excessive current to flow through the relay, burning out its contacts. In that case, you need to have the circuit inspected by a mechanic to find the underlying cause before you replace the relay again.

When a relay problem means something else is wrong

Sometimes a relay stops working because the component it controls has failed or shorted. For example, if your fuel pump relay keeps burning out, the fuel pump itself may be drawing too much current. If your cooling fan relay fails repeatedly, the fan motor may be shorted or the fan may be binding and drawing excessive current.

Before you assume the relay is straightforward worn out, check whether the component it controls is working correctly. If the fuel pump is not running, listen for a humming sound from the fuel tank when you turn the key to the "on" position. If the cooling fan is not spinning, check whether the fan motor is free to rotate and whether the fan clutch (if your vehicle has one) is engaging properly. If the component is not working or is working poorly, the relay may be failing because it is being overloaded.

If you replace a relay and it fails again within a short time, have a mechanic inspect the circuit. The cost of diagnosis is worth avoiding repeated relay replacements and potentially damaging other parts of the electrical system.

Frequently Asked Questions

Can a bad relay cause a car not to start?

Yes. The starter relay controls the large current that flows to the starter motor. If the starter relay is bad, you may hear a clicking sound when you turn the key, or you may hear nothing at all. The engine will not crank. A bad starter relay is one of the most common electrical causes of a no-start condition.

What does it mean if tapping the relay makes it work?

Tapping the relay temporarily closes contacts that are stuck or corroded. This is a sign that the relay is failing and the contacts are not making reliable contact. The relay should be replaced soon, because it will stop working again once the contacts separate.

Can I drive with a bad relay?

It depends on which relay is bad. A bad fuel pump relay will cause the engine to stall or not start at all, so you cannot drive. A bad headlight relay means your headlights will not work, which is unsafe at night. A bad cooling fan relay means the engine may overheat. In most cases, a bad relay affects a critical system, so you should not drive the vehicle until it is replaced.

How long does it take to replace a relay?

Replacement usually takes less than five minutes once you have located the correct relay. You straightforward pull the old relay out and push the new one in. The only time-consuming part is finding the relay box and identifying the correct relay on the diagram, which may take 10 to 15 minutes if you are unfamiliar with your vehicle.

Why do relays fail so often in some cars?

Relays fail more often in vehicles that are exposed to extreme heat, moisture, or vibration. Vehicles driven in hot climates, in areas with high humidity, or on rough roads experience faster relay wear. Some vehicle models also have relays mounted in locations where they are exposed to engine heat or water spray, which shortens their lifespan compared to relays in protected locations.