What a relay does and why it fails
A relay is an electromagnetic switch that uses a small electrical signal to control a larger one. In your car, relays handle high-current jobs like running the fuel pump, cooling fan, headlights, and starter motor. Instead of running heavy wires all the way from the ignition switch to these components, the relay sits in a box under the hood or dashboard and does the switching work locally.
Relays fail because the internal contacts wear out, the coil burns, or moisture gets inside. When a relay goes bad, the component it controls either stops working entirely or works only intermittently. A fuel pump relay failure, for example, will leave you stranded because the engine won't start. A cooling fan relay failure means the fan won't kick on when the engine heats up.
The good news: testing a relay takes minutes and costs nothing if you do it yourself. You need a multimeter (a basic one runs $15 to $30), the relay itself, and the wiring diagram for your specific car to know which pins do what.
Key Takeaways
- A relay is an electromagnetic switch that controls high-current components like the fuel pump, cooling fan, and starter motor.
- You can test a relay with a multimeter by checking for continuity between specific pins and listening for an audible click when power is applied.
- The relay box location and pin layout vary by car model, so you will need your vehicle's wiring diagram or service manual before you start.
- A relay that fails the continuity test or does not click when powered should be replaced; swapping it with an identical relay from another circuit is a quick way to confirm the problem.
- If the replacement relay fails quickly, the problem is usually a short circuit or excessive current draw in the component the relay controls, not the relay itself.
Locating the relay box and identifying the right relay
Relays live in one or more boxes, usually under the hood near the battery or fuse panel, or under the dashboard on the driver's side. Your owner's manual or the inside of the relay box lid will have a diagram showing which relay controls which component. If you do not have the manual, search online for "[your year, make, model] relay box diagram" — most manufacturers post these freely.
Once you find the box, locate the relay you want to test. Relays are small plastic cubes, typically about 1.5 inches on each side, with four or five metal pins sticking out the bottom. The diagram will tell you the relay's position by number or name. Write down the relay's part number before you pull it out — you will need it to buy a replacement if the test shows it is bad.
Pull the relay straight up and out of its socket. Do not force it; they come out easily. Set it aside on a clean surface where you can see the pins clearly.
Testing with a multimeter: the continuity check
A multimeter measures electrical continuity (whether current can flow) and resistance. Set your multimeter to the ohms (Ω) setting, usually marked with the Greek letter omega. Touch one probe to pin 1 and the other to pin 2 on the relay. A good relay will show infinite resistance or "OL" (open line) on the display, meaning no current flows between those pins when the relay is not powered.
Now touch the probes to pins 3 and 4 (the coil pins — your diagram will show which ones). You should see a resistance reading between 50 and 150 ohms, depending on the relay type. If you see zero ohms or infinite resistance, the coil is burned out and the relay is bad.
Next, touch one probe to pin 1 and the other to pin 2 again. This time, hold the probes in place and have a helper explore 12 volts to pins 3 and 4 using a separate 12-volt power source (a car battery works, or a bench power supply). When power reaches the coil, you should hear a distinct click from the relay and see the resistance between pins 1 and 2 drop to near zero ohms. If there is no click and the resistance does not change, the relay is faulty.
The swap test: a faster way to confirm
If you do not have a multimeter or want to confirm the test results, pull an identical relay from a different circuit — one you know is working, like the horn relay or a headlight relay. Swap it into the socket of the relay you suspect is bad, then try the component. If the component suddenly works, the original relay is bad. If it still does not work, the problem is in the wiring or the component itself, not the relay.
This method works because relays are standardized. A relay rated for 12 volts and 30 amps will work in any circuit designed for that specification. Just make sure the replacement relay has the same voltage and amperage rating as the original — the part number will tell you this, or check the relay box diagram.
What to do if the relay tests bad
Buy a replacement relay with the same part number as the one you removed. Take the old relay to an auto parts store and match it against the shelf stock, or order it online. Most relays cost between $10 and $25. Install the new relay by pushing it straight down into the socket until it seats fully — you will feel a slight resistance, then a click as it locks in place.
Start the engine and test the component. The fuel pump should prime, the cooling fan should run, the headlights should come on — whatever that relay controls should work normally now.
If the new relay fails within a few days or weeks, the problem is not the relay itself. A relay that burns out quickly usually means the component it controls is drawing too much current (a short circuit in the component, a seized motor, or a wiring fault). In that case, stop using the component and have a mechanic inspect the wiring and the device it powers before you install another relay.
When to test relays versus when to replace them
Testing makes sense when you suspect a relay is bad but want to confirm before spending money. It also makes sense if you are troubleshooting an intermittent problem — a relay that clicks sometimes but not always is usually failing and should be replaced.
However, if a component has stopped working entirely and you have already ruled out blown fuses and loose connections, replacing the relay is often faster than testing. A $15 relay is cheap insurance, and you can always test the old one afterward to confirm your diagnosis. Many shops will test a relay for free if you bring it in, so you can verify the swap worked before you leave.
Frequently Asked Questions
Can I test a relay while it is still in the car?
You can check the coil resistance with the relay in place, but you cannot do the full continuity test or the power-up click test without removing it. Pulling the relay takes 30 seconds and is worth doing to get a definitive answer.
What does it mean if the relay clicks but the component still does not work?
The relay is fine, but the wiring or component is faulty. Check for blown fuses, corroded connectors, and broken wires leading to the component. A mechanic can trace the circuit with a multimeter to find the break.
Can a relay fail intermittently?
Yes. A relay with worn contacts may click and work sometimes, then fail when the engine vibrates or the temperature changes. If a component works only occasionally, replace the relay first — it is the most likely culprit and the cheapest fix.
Is there a difference between relays with four pins and five pins?
Five-pin relays have an extra contact that allows them to switch between two different circuits. Four-pin relays switch a single circuit on or off. Your wiring diagram will show which type your car uses. They are not interchangeable, so match the part number exactly.
What if I cannot find the relay box diagram?
Search online for your vehicle's year, make, and model plus "relay box diagram" or "fuse box diagram." Most manufacturers post these on their websites or through free repair databases. You can also ask at an auto parts store — they often have access to wiring diagrams and can print one for you.