Filling a grease gun takes about five minutes once you know the process

A grease gun holds thick lubricant under pressure and forces it into tight joints on your vehicle — suspension points, steering linkage, and door hinges. To fill one, you unscrew the barrel from the handle, load a grease cartridge or bulk grease into the barrel, screw it back together, and pump the handle to prime it. The whole job requires only the gun itself, grease, and a rag.

Most home mechanics use cartridge-fed guns because they are cleaner and faster than bulk-fill models. A cartridge is a sealed tube of grease that slides into the barrel; you cut the tip off, load it, and throw it away when empty. Bulk-fill guns require you to pack grease directly into the barrel by hand, which is messier but works fine if you already own one.

Key Takeaways

  • Cartridge-fed grease guns are easier for most people because the grease comes in a sealed tube that you straightforward slide into the barrel.
  • You must cut the tip off a cartridge and puncture the seal inside before the gun will dispense grease.
  • After loading, pump the handle 10 to 15 times to prime the gun and push air out of the barrel.
  • Store filled grease guns with the plunger all the way back to prevent the cartridge from drying out.

Choosing between cartridge and bulk-fill models

A cartridge-fed gun holds a pre-packaged tube of grease. These are the standard choice for home use because you load a new cartridge each time, so there is no mess and no cleanup. The cartridge costs a few dollars and you discard it when empty. Most auto parts stores stock them in standard sizes — 14 ounces is common — and they fit any gun with a standard barrel.

A bulk-fill gun has an open barrel that you pack with loose grease from a can or bucket. These are cheaper upfront and work well if you grease many vehicles regularly, but they require you to hand-pack the grease and clean the barrel afterward. For occasional home maintenance, a cartridge gun is faster and less messy.

Loading a cartridge into the barrel

Start by unscrewing the barrel from the handle. Most guns have a collar or ring at the base of the barrel that you turn counterclockwise by hand — no tools needed. Pull the barrel straight out and set the handle aside.

Take a grease cartridge and look at the sealed end. You will see a small metal or plastic cap covering the tip. Use a utility knife or the small blade on a multi-tool to cut off about one-quarter inch of the cartridge tip at an angle. This exposes the opening where grease will flow out. Do not cut too much or you will waste grease; just enough to open the hole.

Slide the cartridge into the barrel with the cut end pointing toward the front of the gun. The cartridge should fit snugly. If it is loose, the gun is the wrong size — cartridges come in standard diameters and you need the right match. Once the cartridge is seated, screw the barrel back onto the handle by turning the collar clockwise until it is hand-tight. Do not over-tighten.

Puncturing the cartridge seal and priming the gun

Inside the cartridge is a foil or plastic seal that prevents grease from leaking during storage. The plunger rod at the back of the handle must puncture this seal before grease can flow. Screw the handle's plunger rod clockwise by hand until you feel resistance — usually two to four full turns. You will hear or feel a small pop when the seal breaks. This is normal.

Now pump the handle up and down 10 to 15 times. The first few pumps will push air out of the barrel and force grease toward the nozzle. You may see nothing come out at first, but keep pumping. After several strokes, grease will begin to appear at the tip. Once grease flows steadily, the gun is primed and ready to use.

Filling a bulk-fill gun with loose grease

Unscrew the barrel from the handle and set the handle aside. Open a can or bucket of grease — lithium-based grease is standard for most vehicle joints. Using a putty knife or old spoon, scoop grease directly into the barrel. Pack it down firmly as you go, removing air pockets. Fill the barrel until grease is about one-half inch from the top.

Screw the barrel back onto the handle and hand-tighten the collar. Pump the handle 10 to 15 times to prime the gun and push out trapped air. Grease will begin to flow from the nozzle after several strokes. Wipe the nozzle with a rag to remove excess before you start greasing your vehicle.

Maintenance and storage of a filled gun

After you finish greasing, wipe the nozzle clean with a rag. If you plan to use the gun again within a few days, you can leave it loaded. Store it with the plunger rod all the way back — turn it counterclockwise until it stops. This relieves pressure on the cartridge and prevents the grease from drying out or leaking.

If you will not use the gun for several weeks, unload the cartridge and store it separately in a cool, dry place. Grease can harden or separate if left in the gun for months. Before you use the gun again after a long storage period, pump it several times to re-prime it and check that grease still flows smoothly.

Clean the nozzle tip regularly with a rag or old cloth. Dried grease can clog the opening and prevent flow. If the nozzle becomes blocked, soak it in a small cup of mineral spirits for a few minutes, then wipe it clean and dry it thoroughly before reattaching to the gun.

Troubleshooting common filling problems

If grease does not flow after you have pumped the gun 15 times, the cartridge seal may not have punctured. Screw the plunger rod in another full turn or two and pump again. If the gun still does not dispense grease, the cartridge may be the wrong size for your barrel — check the cartridge diameter against your gun's specifications.

If grease leaks from the collar where the barrel meets the handle, the connection is not tight enough. Unscrew the barrel, wipe the threads clean with a rag, and screw it back on firmly. Do not force it or you may strip the threads. A small amount of leakage is normal during use, but steady dripping means the seal is not seated properly.

If the plunger rod becomes stuck or very hard to turn, do not force it. The cartridge may be empty or the grease may have hardened. Unload the gun, inspect the cartridge, and replace it if necessary. If the rod itself is stuck, soak the handle in warm water for 10 minutes to soften any dried grease, then try again gently.

Frequently Asked Questions

What type of grease should I use in my vehicle?

Lithium-based grease is the standard for most vehicle suspension and steering joints. Check your owner's manual or the grease fittings themselves — some are labeled with the type required. Do not mix different grease types in the same joint; always use the same type for refilling.

Can I refill a cartridge instead of throwing it away?

Refilling cartridges is not practical for home use. The cartridges are sealed at the factory and designed to be single-use. Buying new cartridges is cheaper and cleaner than trying to refill old ones. Bulk-fill guns are the better choice if you want to reuse containers.

How often should I fill my grease gun?

That depends on how often you grease your vehicle. Most home mechanics grease suspension and steering joints once a year or every 12,000 miles. Keep a filled gun in your garage so you can grease as needed without waiting to buy cartridges.

What happens if I over-tighten the barrel onto the handle?

Over-tightening can strip the threads or crack the plastic handle. Hand-tight is sufficient — you should be able to unscrew it by hand without tools. If you cannot unscrew it later, you may have tightened it too much and damaged the connection.

Can I use a grease gun on door hinges and other household items?

Yes. The same grease gun works on car suspension, door hinges, garage door tracks, and any other joint that needs lubrication. Just make sure you use the right type of grease for each process — automotive lithium grease works for most household uses too.