The basic steps to fill a grease gun
A grease gun holds thick lubricant under pressure and forces it into tight joints and bearings on your vehicle. Filling one takes about five minutes and requires only the grease cartridge itself and sometimes a small tool to remove the old one. Most grease guns use a cartridge system — you slide a new tube of grease into the barrel, lock it in place, and pump the handle until grease comes out the nozzle.
The exact steps depend on whether your gun is a pistol-grip model (the most common type) or a caulking-style model, but the principle is the same: remove the empty cartridge, insert a full one, and prime the gun by pumping until grease appears at the tip.
Key Takeaways
- Most grease guns use disposable cartridges that slide into the barrel from the back and lock with a collar or cap.
- You must remove the empty cartridge completely before inserting a new one, or the gun will not build pressure.
- After inserting a fresh cartridge, pump the handle 10 to 15 times without the gun attached to anything to prime it and push out air.
- Grease cartridges come in standard sizes (14 ounces is most common for automotive work), and the nozzle tip screws on and off so you can match it to different fittings.
Removing the empty cartridge
Unscrew the barrel cap or collar at the back of the gun — this is usually a large knurled ring you can turn by hand. Pull the barrel straight out from the handle. The empty cartridge will slide out with it or stay inside the barrel; either way, discard it.
If the cartridge is stuck, do not force it. Wipe the inside of the barrel with a clean rag to remove old grease buildup, which often causes cartridges to jam. A small amount of mineral spirits on the rag helps, but do not soak the barrel or let liquid drip into the pump mechanism.
Inserting the new cartridge
Slide the new grease cartridge into the barrel with the narrow nozzle end pointing toward the front of the gun. The cartridge should sit flush against the back of the barrel. Screw the barrel cap back on hand-tight — do not use a wrench, as you can strip the threads.
Some guns have a small metal rod or plunger inside the barrel that must be seated against the cartridge's flat back end. If your gun has one, make sure it is fully inserted before you screw the cap on. You will feel slight resistance as the plunger contacts the cartridge, which is normal.
Priming the gun to remove air
Before you attach the gun to a grease fitting on your vehicle, pump the handle 10 to 15 times while pointing the nozzle into a waste container or rag. This pushes out the air pocket between the old cartridge and the new one. You will see grease start to ooze from the tip after several pumps.
Priming is essential because if you attach the gun to a fitting while air is still in the barrel, the first few pumps will push air into the joint instead of grease. This wastes grease and leaves the bearing under-lubricated. Once grease flows steadily from the nozzle, the gun is ready to use.
Choosing the right cartridge size and type
Standard automotive grease cartridges are 14 ounces, which fit most pistol-grip guns. Some smaller or specialty guns use 3-ounce cartridges, and a few heavy-duty models use larger sizes. Check your gun's manual or the barrel itself — the size is usually printed on the side.
Grease types vary by process. Lithium-based grease is the most common for general automotive use and works on suspension joints, wheel bearings, and U-joints. Moly grease (molybdenum disulfide) is thicker and better for high-load applications. Synthetic grease handles extreme temperatures. Use the type your vehicle's manual specifies for each fitting; mixing types is usually harmless but unnecessary.
Matching the nozzle to the fitting
The nozzle screws onto the front of the barrel and comes in different shapes to match the grease fittings on your vehicle. A straight nozzle works on most accessible fittings. A 90-degree angled nozzle reaches fittings in tight spaces. A needle nozzle fits small or recessed fittings.
Unscrew the old nozzle by turning it counterclockwise, then screw on the one that matches your fitting. Hand-tighten only — over-tightening can crack the plastic nozzle or damage the fitting. If the nozzle does not seat firmly, the threads may be stripped; replace the nozzle rather than forcing it.
Troubleshooting common filling problems
If grease leaks from the back of the barrel after you insert a new cartridge, the plunger rod is not fully seated. Unscrew the cap, push the rod in firmly, and screw the cap back on. If it still leaks, the cartridge may be damaged or the wrong size — remove it and try a fresh one.
If the gun will not pump after you fill it, air may be trapped in the pump mechanism itself, not just the barrel. Pump the handle 20 to 30 times slowly and steadily; the air will eventually work out. If the handle becomes rock-hard and will not move, stop — forcing it can break the pump. Let the gun sit for an hour, then try again; sometimes pressure builds and then releases.
Frequently Asked Questions
Can I refill a cartridge instead of buying a new one?
Refilling is possible but not practical for most vehicle owners. Cartridges are inexpensive (usually $3 to $8 each), and the equipment to refill them costs more than buying new ones. Some industrial suppliers offer bulk grease in 5-pound buckets for shops that use large quantities, but those require a different gun setup.
What should I do if grease comes out the back of the gun while I am using it?
This means the cartridge is empty or the plunger has separated from it. Stop using the gun, unscrew the barrel cap, and check whether the cartridge is fully inserted and the plunger is seated against it. If the cartridge is empty, replace it. If the plunger has slipped, reseat it and try again.
How long does a grease cartridge last?
A 14-ounce cartridge typically lubricates 8 to 12 vehicle fittings, depending on how much grease each fitting needs. Suspension joints and U-joints usually take more than wheel bearings. You will empty a cartridge faster if you are servicing multiple vehicles or doing a full chassis lubrication.
Can I use any brand of grease in my gun?
Yes, as long as the cartridge fits your gun's barrel size. Different brands vary slightly in thickness and additives, but they work in the same cartridge system. Stick with the grease type your vehicle manual recommends for each fitting, but the brand does not matter.
Should I store a filled grease gun with the cartridge in it?
Yes, leaving the cartridge in place is fine for storage. Keep the gun in a cool, dry place away from direct sunlight, which can harden grease over time. If you store it for more than a few months, pump the handle a few times before using it again to loosen the grease and restore pressure.