Tire chains go over your tires to grip snow and ice, and you install them before you drive into deep snow
Tire chains are metal links that wrap around your tire tread and bite into snow and ice, giving you traction when regular tires can't grip. You fit them over the tire while the vehicle is parked on flat, clear ground—never while driving or on a slope. The job takes 15 to 30 minutes per axle once you know the steps, and doing it wrong means the chain can break, damage your wheel well, or come loose while you drive.
Most people install chains on the drive wheels only (front wheels on front-wheel-drive cars, rear wheels on rear-wheel-drive cars). Some vehicles and some snow conditions call for all four wheels, so check your owner's manual and local chain laws—some mountain passes require chains on all four tires during storms, and some prohibit certain types of chains altogether.
Key Takeaways
- Park on level ground away from traffic, turn off the engine, and set the parking brake before you start fitting chains to any tire.
- Lay the chain flat on the ground, drape it over the tire, and thread the bottom end up through the center, then fasten the side hooks or clasps according to your chain's design.
- Drive forward slowly (2 to 3 miles per hour) for 50 to 100 feet, stop, and retighten every connection because chains settle and loosen after the first few feet of driving.
- Remove chains as soon as you reach clear pavement, because driving on dry asphalt wears them out fast and damages the road surface.
- Store chains dry in a bag or box in your trunk year-round if you live in or travel to snow country, because they rust if left damp.
Choosing the right chain type and size for your vehicle
Tire chains come in three main types: ladder chains (the cheapest, with rungs connecting two side rails), diamond chains (stronger, with a diamond pattern that grips better), and cable chains (lighter and easier to install, but less durable). Ladder chains cost $30 to $60 per pair, diamond chains run $60 to $100, and cable chains fall in the middle. The trade-off is that cable chains wear out faster and don't grip as well on very steep or icy terrain.
You must buy chains sized for your exact tire. The size is printed on your tire sidewall as a series of numbers and letters—for example, 225/65R17. Take that number to an auto parts store or look it up on the chain manufacturer's website. Buying the wrong size means the chain won't fit, or it will be so loose it comes off while you drive. If you are unsure, bring a photo of your tire sidewall to the store and ask the staff to confirm the chain size before you buy.
Some newer vehicles have limited wheel-well clearance and cannot fit standard chains. Check your owner's manual under "tire chains" or "snow tires" to see if your car has restrictions. If it does, you may need to buy low-profile or compact chains, which cost more but fit tighter spaces. A few luxury and sports cars cannot use chains at all and require winter tires instead.
Preparing your vehicle and workspace
Find a flat, level spot away from traffic—a parking lot or wide shoulder is ideal, never a slope or the side of a moving highway. Turn off the engine, set the parking brake firmly, and turn on your hazard lights. If it is dark, turn on your headlights or use a flashlight so you can see what you are doing.
Lay out both chains on the ground in front of you before you touch the tires. Spread each chain flat and look for any twisted links or damage. If a chain is kinked or a link is bent, do not use it—a damaged chain can break while you drive and wrap around your suspension or axle. Inspect the fasteners (hooks, clasps, or tighteners) to make sure they move freely and are not rusted shut.
Deflate your tires slightly—about 2 to 3 pounds per square inch below the recommended pressure—to give the chain more grip on the tread. You will reinflate them after you remove the chains. This step is optional but recommended, especially on ice or very steep terrain.
Installing chains step by step
Start with the driver's side front tire (or the appropriate drive wheel for your vehicle). Drape the chain over the top of the tire so it hangs evenly on both sides. The chain should sit in the center of the tread, not on the sidewall.
Pick up the bottom end of the chain and thread it up through the middle of the tire, pulling it tight. You should now have chain on the top and bottom of the tire with the side sections hanging loose. Fasten the side connections according to your chain type: ladder and diamond chains usually have hooks that you loop over studs or through links on the opposite side, while cable chains have clasps or tighteners you turn by hand or with a wrench.
Tighten every connection firmly but do not over-tighten—you should not be able to move the chain by hand, but you also should not bend or break the fasteners. Leave about one finger's width of space between the chain and the tire sidewall so the chain can move slightly as the tire flexes.
Repeat the process on the second drive wheel. If your vehicle or local law requires chains on all four tires, install them on the rear wheels the same way.
Testing and retightening after you start driving
Drive forward slowly at 2 to 3 miles per hour for 50 to 100 feet, then stop completely. Get out and check every fastener on every chain. Chains settle and loosen after the first few feet of movement, and a loose chain can come off, wrap around your suspension, and cause serious damage. Tighten anything that has moved, then drive another 100 feet and check again.
Once you have driven a quarter mile or so and confirmed that all chains are tight and sitting properly, you can drive at normal winter speeds—usually 25 to 35 miles per hour depending on road conditions and visibility. Chains are loud and the ride will be rougher than normal; this is expected. Do not exceed 30 miles per hour with chains on, because speed increases the stress on the chain and the risk of breakage.
Listen for any unusual sounds—a clanging or rattling that changes with the tire rotation usually means a chain is loose or damaged. If you hear this, pull over when ready, turn off the engine, and inspect the chains. A chain that has come partially off can wrap around the axle or suspension and cause expensive damage if you keep driving.
Removing chains and storing them properly
Remove chains as soon as you reach clear, dry pavement. Driving on asphalt wears chains out rapidly and damages the road surface. Pull over in a safe spot, turn off the engine, and set the parking brake. Unfasten all the side connections, then pull the chain out from under the tire. Repeat for each chain.
Before you store the chains, wipe them down with a dry cloth to remove any snow or moisture. Lay them out to air-dry completely—at least a few hours in dry conditions. Once they are dry, coil each chain loosely (do not fold them tightly, which can kink the links) and store them in a plastic bag or cardboard box in your trunk or garage.
Chains rust quickly if stored damp, so never put them away wet. If you live in a humid climate or near the ocean, spray the chains lightly with a rust-preventive oil before storing them. Check them once a year before winter to make sure no links are corroded or broken.
Common mistakes and how to avoid them
The most common mistake is installing chains too loosely. A chain that moves on the tire will catch on the wheel well, break, or come off entirely. After you drive the first 100 feet, stop and retighten every connection—this is not optional. Many people skip this step and end up stranded or with a damaged vehicle.
Another frequent error is installing chains on the wrong wheels. Check your owner's manual to confirm which wheels need chains. If you put chains on the rear wheels of a front-wheel-drive car, you lose traction where you need it most and may lose control on a hill.
Some drivers install chains while the vehicle is still moving or on a slope, which is dangerous and makes the job much harder. Always park on level ground, turn off the engine, and set the brake before you touch the chains. If you are on a highway, move to a wide shoulder or exit to a parking area if possible.
Finally, do not drive faster than 30 miles per hour with chains on, and do not drive on dry pavement any longer than necessary. Chains are designed for snow and ice only, and they wear out and damage asphalt quickly.
Frequently Asked Questions
Can I install chains while driving or on a slope?
No. Always park on level, clear ground with the engine off and the parking brake set. Installing chains while moving is dangerous, and the angle of a slope makes the job much harder and increases the risk of the chain slipping or the vehicle rolling.
Do I need chains on all four tires or just the drive wheels?
Most vehicles need chains on the drive wheels only. However, some mountain passes and some vehicle types require all four tires to be chained during storms. Check your owner's manual and any posted signs on the road you are about to travel. Local law enforcement can also tell you what is required.
What should I do if a chain breaks while I am driving?
Pull over to a safe spot when ready, turn off the engine, and set the parking brake. Remove the broken chain and the chain on the other drive wheel (so you have even traction). Drive slowly to the nearest town or service station. Do not continue driving with chains on only one side, because uneven traction can cause you to lose control.
How do I know if my vehicle can use chains?
Check your owner's manual under "tire chains" or "winter driving." Some vehicles with low ground clearance or tight wheel wells cannot fit standard chains and may require low-profile chains or winter tires instead. If you are unsure, call your vehicle's dealership with your vehicle's year, make, and model.
Can I reuse chains from year to year?
Yes, if you store them dry and inspect them before each winter. Wipe them down after use, let them air-dry completely, and store them in a bag or box in a dry place. Check for rust, bent links, or broken fasteners before you install them again. Chains last several years with proper care.