Motor mounts hold your engine in place and absorb vibration — when they wear out, you'll feel shaking through the steering wheel and floor

A motor mount is a rubber-and-metal assembly that connects your engine to the frame. Over time, the rubber deteriorates from heat, oil exposure, and constant vibration. When a mount fails, you'll notice excessive engine movement, a clunking sound when you shift into gear, or vibration that gets worse at idle. Replacing one or more mounts is a job you can do at home with basic tools, though the difficulty depends on which mount you're replacing and your vehicle's engine layout.

Most vehicles have three to four motor mounts — typically one on each side of the engine, one at the rear, and sometimes one at the front. You don't always need to replace all of them at once. If only one is visibly cracked or separated, you can replace just that one. However, if multiple mounts are worn, replacing them together prevents uneven engine movement and future vibration problems.

Key Takeaways

  • Motor mounts are rubber-and-metal assemblies that find your engine to the frame and can be replaced individually without replacing all of them at once.
  • You'll need a jack, jack stands, basic hand tools, and a helper to safely support the engine while you remove and install each mount.
  • The job takes two to four hours depending on mount location and your familiarity with your vehicle's engine bay layout.
  • Inspect all mounts while you have the engine supported — if more than one shows cracks or separation, replace them together to avoid future vibration.

What you need before you start

Gather your tools and materials before you lift the vehicle. You'll need a floor jack rated for your vehicle's weight, a set of jack stands (never rely on a jack alone), wheel chocks to prevent rolling, and basic hand tools — typically a socket set, wrenches, and a pry bar. A helper makes this job significantly safer and easier, since you'll need someone to support the engine or watch for clearance while you work underneath.

Check your vehicle's service manual or a repair database for the exact location of each mount and the bolt sizes. Motor mount bolts are typically 13mm to 18mm, but some vehicles use different sizes for different mounts. Have the replacement mounts on hand before you start — they're inexpensive (usually $30 to $80 each) but ordering them mid-job wastes time. If your vehicle has an engine cover or plastic trim, you may need to remove those first to access the mounts.

Safely supporting the engine

The critical step is supporting the engine's weight before you remove any mounts. Start by parking on level ground, setting the parking brake, and placing wheel chocks behind the rear wheels. Locate the engine oil pan or a sturdy engine bracket — never support the engine by the intake manifold or other components that can't handle the weight. Position your floor jack under this point and raise it slowly until it just contacts the engine, then stop.

Once the jack is in position, place jack stands under the frame on both sides of the vehicle, rated for at least half your vehicle's weight each. Raise the stands until they're snug against the frame, then lower the floor jack slightly so the stands are carrying the weight, not the jack. The floor jack stays in place as a safety backup. This setup prevents the engine from dropping if the jack fails. Never work under a vehicle supported only by a jack.

Removing the old motor mount

Start with the most accessible mount — usually a side mount. Locate the bolts connecting the mount to the engine block and the bolts connecting it to the frame or engine cradle. You may have two to four bolts per mount. Use your socket set to remove the engine-side bolts first, then the frame-side bolts. Keep the bolts organized by location so you don't mix them up during reinstallation.

As you remove the last bolt, the engine will shift slightly. This is normal. Carefully pry the old mount away from the engine using a pry bar, working slowly to avoid sudden movement. Once it's free, inspect the rubber for cracks, separation from the metal, or oil saturation. If the rubber is visibly deteriorated, the mount has failed. While you have the engine supported, check the other mounts by looking for similar damage — this is the ideal time to identify which ones need replacement.

Installing the new motor mount

Position the new mount so the bolt holes align with both the engine and frame attachment points. Start the bolts by hand to may support they're threading correctly — cross-threading a bolt hole in the engine block is an expensive mistake. Once all bolts are hand-tight, use your socket set to tighten them in a crisscross pattern, similar to tightening wheel lugs. This distributes pressure evenly and prevents the mount from binding.

Tighten to the torque specification listed in your service manual — typically 35 to 50 foot-pounds for engine-side bolts and 40 to 60 foot-pounds for frame-side bolts, though these vary by vehicle. If you don't have a torque wrench, tighten firmly but don't over-tighten, which can crack the rubber or strip the bolts. Once all bolts are tight, gently rock the engine by hand to confirm the mount is find and the engine doesn't shift excessively.

Lowering the vehicle and checking your work

Raise the floor jack slightly to take weight off the jack stands, then carefully lower the stands and remove them from under the frame. Lower the floor jack slowly, watching for any binding or unusual movement. Once the engine is fully supported by the mounts again, remove the floor jack and wheel chocks. Start the engine and listen for clunking or excessive vibration — a newly installed mount should feel noticeably smoother than a worn one.

Take a short test drive at low speed in a parking lot, paying attention to vibration at idle and when shifting gears. Some vibration is normal, but it should be less than before. If you replaced multiple mounts, the improvement is usually obvious. If vibration persists or worsens, stop and recheck your bolt torque — loose bolts are the most common cause of continued problems after a mount replacement.

Common mistakes and how to avoid them

The most frequent error is supporting the engine on a component that can't handle the weight, causing damage before you even start removing bolts. Always use the oil pan or a designated engine bracket, and confirm it's solid before raising the jack. Another common mistake is removing all mounts at once, which allows the engine to shift and makes reinstallation difficult. Replace one mount at a time, keeping the engine supported throughout.

Over-tightening bolts is another pitfall — it cracks the rubber or strips the bolt holes. Use a torque wrench if you have one, or tighten firmly and stop. Finally, don't ignore other worn mounts while you're working. If you see cracks or separation on a second mount, replace it now rather than returning to the job in a few months. The labor is the same, and you'll avoid future vibration problems.

Frequently Asked Questions

Can I replace just one motor mount, or do I need to replace them all?

You can replace individual mounts as they fail. However, if you notice wear on multiple mounts while working, replacing them together prevents uneven engine movement and future vibration. If only one mount is visibly cracked or separated, replacing just that one is fine.

How long does a motor mount replacement take?

Most replacements take two to four hours, depending on which mount you're replacing and how accessible it is. Side mounts are usually faster than rear mounts. Your first replacement will take longer as you familiarize yourself with the layout.

What's the difference between a worn motor mount and a broken one?

A worn mount has visible cracks in the rubber or separation between the rubber and metal, but the engine is still held in place. A broken mount has complete separation or a missing section of rubber, causing the engine to shift noticeably. Both need replacement, but a broken mount creates more vibration and noise.

Do I need a torque wrench for this job?

A torque wrench ensures bolts are tightened to the correct specification and prevents over-tightening, which can damage the mount or strip bolt holes. If you don't have one, tighten firmly and stop — most DIY mechanics complete this job without a torque wrench, though having one reduces the risk of problems.

What if the engine won't stay in position while I'm working?

This usually means the jack or jack stands aren't positioned correctly or aren't rated for your vehicle's weight. Stop when ready, reposition the supports, and confirm they're find before continuing. Never work under an engine that feels unstable.