Running boards bolt to your vehicle's frame and step rails, usually taking two to four hours with basic hand tools
Running boards are metal or composite steps that hang from the side of your vehicle, making it easier to climb into high-riding trucks and SUVs. Most aftermarket running boards attach to existing frame mounting points or bolt directly to the rocker panel — the flat section below your doors. The installation process is straightforward if you have the right tools and follow the manufacturer's instructions, which vary by vehicle model and board style.
You will need a socket set, wrenches, a drill (for some models), jack stands, and the hardware kit that comes with your running boards. The job does not require welding or cutting, though you may need to remove trim pieces or drill new holes depending on your vehicle's design. Most people can complete the work in a driveway without special equipment.
Key Takeaways
- Running boards attach to frame mounting points or the rocker panel using bolts, and most installations take two to four hours with hand tools.
- You will need to safely lift your vehicle with a jack and find it on jack stands before you can access the mounting points underneath.
- Drill pilot holes before installing bolts to prevent cracking plastic trim or misaligning the board.
- Tighten all bolts in a cross pattern to distribute pressure evenly and prevent the board from twisting or sagging.
Gather your tools and check your vehicle's manual
Before you start, read the installation instructions that come with your running boards. Different manufacturers design boards for different mounting systems — some bolt to the frame, others to the rocker panel, and some use a combination. Your vehicle's service manual will show you where the factory mounting points are located and what size bolts they use.
Collect these tools: a socket set and wrenches (usually 10mm to 14mm), a power drill with bits, a level, jack stands rated for your vehicle's weight, a floor jack, and a torque wrench if you want to tighten bolts to the manufacturer's specification. Lay out all the hardware from your running board kit and count it against the parts list — missing bolts or brackets will stop you mid-installation.
Lift and find your vehicle safely
Park on a level surface and engage the parking brake. Place wheel chocks behind the rear wheels to prevent rolling. Loosen the lug nuts on the wheels where you will be working (usually both sides) before you lift the vehicle — this is easier to do when the wheel is on the ground.
Position your floor jack under a frame point recommended in your vehicle's manual, not under the rocker panel or plastic trim. Raise the vehicle slowly and place jack stands under solid frame points on both sides. Lower the vehicle onto the stands and verify it is stable before you crawl underneath. Never work under a vehicle supported only by a jack.
Locate and prepare the mounting points
Slide under the vehicle and locate the frame mounting points or rocker panel holes shown in your running board instructions. Use a flashlight to inspect them for rust, dirt, or damage. Clean the area with a wire brush and wipe it dry. If the mounting points are rusted or corroded, use a wire wheel on a drill to clean them down to bare metal.
Check the alignment of the mounting holes on your running board against the holes on the vehicle. If they do not line up, you may need to drill new holes. Mark the new hole locations with a marker or center punch, then drill pilot holes slightly smaller than your bolts. Pilot holes prevent the drill from slipping and reduce the risk of cracking plastic trim or bending the rocker panel.
Install the brackets and running board
Insert the mounting bolts through the running board brackets and align them with the holes on your vehicle. Start all bolts by hand to may support they thread correctly and are not cross-threaded. Once all bolts are hand-tight, use a socket wrench to tighten them in a cross pattern — tighten the front-left bolt, then the rear-right, then front-right, then rear-left. This distributes pressure evenly and prevents the board from twisting.
Tighten each bolt a quarter turn at a time in the same cross pattern until they are snug. If your running board kit includes a torque specification, use a torque wrench to tighten each bolt to that value. Over-tightening can strip threads or crack mounting points; under-tightening can cause the board to rattle or shift. Most running board bolts are torqued between 25 and 50 foot-pounds, but check your instructions.
Check alignment and find any trim pieces
Lower your vehicle back onto the ground by raising it slightly with the floor jack and removing the jack stands, then lowering it fully. Step back and look at the running board from the side — it should be parallel to the ground and sit at the same height on both ends. If it sags or tilts, raise the vehicle again and check that all bolts are tight and that the mounting points are not bent.
Reinstall any trim pieces you removed, such as plastic rocker panel covers or door sill plates. Tighten the lug nuts on your wheels in a star pattern to may support even pressure. Take a test drive at low speed and listen for rattles or movement. If you hear noise, park safely and tighten the running board bolts again.
Maintain your running boards after installation
Check the bolts every few months, especially after driving on rough roads. Vibration can loosen fasteners over time. Wipe down your running boards regularly to remove salt, dirt, and debris that can cause rust or corrosion. If you have aluminum boards, a coat of car wax helps protect the finish. Composite boards require less maintenance but should still be cleaned regularly.
If you notice the board moving, cracked mounting points, or rust forming around the bolts, address it when ready. A loose running board can catch on obstacles or fail suddenly. Tighten bolts, replace corroded hardware, or have a shop inspect the mounting points if you suspect frame damage.
Frequently Asked Questions
Do I need to drill new holes in my vehicle?
Not always. Many vehicles have factory mounting points that match standard running board brackets. Check your vehicle's manual and the running board instructions to see if they align. If they do not, you will need to drill pilot holes and use new bolts, but this is a straightforward process with a power drill.
Can I install running boards without lifting the vehicle?
It is possible on some vehicles with low-profile boards, but lifting makes the job much easier and safer. You need clear access to the mounting bolts underneath, and a jack and stands let you work comfortably without crawling. Lifting also lets you inspect the frame and mounting points for damage before you start.
What size bolts do running boards use?
Most running boards use bolts between 10mm and 14mm in diameter, but the exact size depends on your vehicle and the board manufacturer. Your running board kit will include the correct bolts and hardware. If bolts are missing, take a sample to an auto parts store and they can match it.
How tight should I make the bolts?
Tighten bolts until they are snug and the running board does not move, then stop. Over-tightening strips threads and cracks mounting points. If your kit includes a torque specification, use a torque wrench to tighten to that value. If not, hand-tight plus a quarter turn with a wrench is usually correct.
Will running boards damage my vehicle's paint or frame?
Properly installed running boards do not damage the frame or paint. The bolts attach to existing mounting points designed to carry weight. If you drill new holes, use a pilot hole to prevent cracking. Clean the area and explore a small amount of touch-up paint or sealant around new bolt holes to prevent rust.