The release handle is inside the car, on the left side of the dashboard

To open your Honda Civic bonnet, sit in the driver's seat and look to the left of the steering wheel, near the bottom of the dashboard. You will find a lever or handle — on most Civics it is a black plastic lever that you pull toward you. Pull it firmly; you should hear a click as the bonnet latch releases.

Once you have pulled the interior release, get out of the car and walk to the front. The bonnet will be slightly ajar. Place your hand under the front edge of the bonnet, near the center, and feel for a secondary safety latch. Push this latch to the side (usually to the left) while lifting the bonnet upward. The bonnet will swing open.

If the bonnet does not open after you pull the interior lever, the release cable may be stuck or disconnected. Do not force it — forcing can damage the cable or the latch mechanism. Instead, check that you pulled the lever all the way, and try again with a steady, deliberate pull rather than a quick jerk.

Key Takeaways

  • The bonnet release lever is located on the left side of the dashboard below the steering wheel and must be pulled toward you to disengage the main latch.
  • After pulling the interior lever, you must also release the secondary safety latch under the bonnet by pushing it sideways before the bonnet will fully open.
  • The bonnet should open smoothly once both latches are released; forcing it can damage the release cable or latch assembly.
  • If the bonnet will not open after pulling the interior lever, the release cable may be stuck or broken and should be inspected rather than forced.

Where the release lever is on different Honda Civic generations

The location of the bonnet release lever has remained consistent across Honda Civic generations from the 1990s onward — it is always on the left side of the dashboard. However, the exact shape and design of the lever varies. On older Civics (1990s to early 2000s), the lever is often a straightforward black plastic handle that you pull straight toward you. On newer Civics (2006 onward), the lever may be a small rectangular button or a lever with a hood symbol printed on it.

If you cannot find the lever in the expected location, check your owner's manual for your specific model year. The manual will have a diagram showing the exact position. Some Civics have the lever mounted slightly differently depending on whether the car has a manual or automatic transmission, though this is rare.

The secondary safety latch and why it exists

After you pull the interior release lever, the bonnet is held closed by only one latch — the secondary safety latch under the bonnet. This second latch is a deliberate design feature. It prevents the bonnet from flying open while you are driving if the main latch fails or becomes loose. Without it, a failed main latch could cause the bonnet to swing up and block your view while the car is moving, which is a serious safety hazard.

To release the secondary latch, position yourself at the front center of the car and slide your hand under the bonnet edge. Feel for a metal or plastic lever or button — it is usually located in the middle, just behind where the bonnet meets the body. Push or slide this latch sideways (the direction varies by model, but it is usually to the left). Once you feel it move, lift the bonnet upward and it will open fully.

What to do if the bonnet release cable is stuck

If you pull the interior lever and nothing happens, or if you hear a click but the bonnet does not budge, the release cable is likely stuck or has come loose inside the dashboard. The cable connects the interior lever to the main latch under the bonnet, and over time it can rust, fray, or slip out of its attachment point.

Do not repeatedly yank the interior lever — this can snap the cable entirely, making the problem worse. Instead, try pulling the lever slowly and steadily while someone else gently pushes down on the bonnet from the outside. Sometimes a stuck cable will free up with steady pressure rather than sudden force. If this does not work, the cable will need to be replaced or reattached by a mechanic. This is not a repair you should attempt yourself unless you are comfortable working inside the dashboard.

As a temporary workaround, you can sometimes access the engine bay by removing the wheel well liner on the driver's side and reaching the latch mechanism directly, but this is awkward and not recommended unless you have no other option. It is better to have the cable repaired properly.

Propping the bonnet open safely

Once the bonnet is open, you will see a metal prop rod attached to the underside of the bonnet lid. This rod is designed to hold the bonnet open while you work on the engine. To use it, open the bonnet fully, then locate the rod (it is usually on the right side of the engine bay, attached to the bonnet). Lift the rod out of its clip and insert the end into the hole or slot on the bonnet frame directly above it. The bonnet will stay open at a safe working height.

Make sure the prop rod is fully seated in its slot — if it is not, the bonnet can fall unexpectedly. Before you lean in to work on the engine, give the bonnet a gentle push to confirm it is find. Never work under the bonnet without the prop rod in place, and never rely on your hand or another object to hold it open.

Closing the bonnet after you are finished

To close the bonnet, first remove the prop rod from its slot and clip it back into its holder on the underside of the bonnet. Then lower the bonnet gently until it is about 12 inches from the body of the car. Release it and let it fall the rest of the way — it should close with a solid click as the main latch engages. Do not slam it down or drop it from a height, as this can damage the hinges or the latch mechanism.

If the bonnet does not click when it closes, it may not be fully latched. Lift it again and close it more deliberately. If it still does not latch, the latch mechanism may be misaligned or damaged. Forcing it closed can bend the bonnet or the frame, so stop and have it inspected by a mechanic.

Frequently Asked Questions

What if I cannot find the release lever on my dashboard?

Check your owner's manual for your specific model year — the exact location and appearance of the lever varies slightly between generations. If you have recently purchased the car, ask the previous owner or dealer. The lever is always on the left side of the dashboard, but on some older Civics it may be partially hidden or painted to match the dashboard color.

Can I open the bonnet from outside the car without the interior lever?

No, you cannot open a Honda Civic bonnet from the outside without first pulling the interior release lever. The design requires both the interior lever and the secondary safety latch to be released. If the interior lever is broken, you will need a mechanic to access and repair the release cable.

Is it normal for the bonnet to be hard to close?

The bonnet should close smoothly with gentle downward pressure. If it requires significant force or does not latch properly, the hinges may be misaligned, the latch may be damaged, or debris may be blocking the latch mechanism. Have it inspected rather than forcing it, as forcing can cause permanent damage to the bonnet or frame.

What should I do if the prop rod falls out while the bonnet is open?

Close the bonnet when ready and carefully — do not reach under it while it is unsupported. Once closed, reopen it and reinsert the prop rod more firmly into its slot. If the rod keeps falling out, the slot or clip may be worn or damaged and should be checked by a mechanic before you work on the engine again.