Find the bonnet release lever inside your car
The bonnet release lever is almost always located on the left side of the driver's seat, either on the floor panel or mounted on the dashboard below the steering wheel. Look for a handle with a picture of an open bonnet on it — the symbol is standardized across manufacturers. Pull this lever toward you with moderate force; you should hear a click or feel resistance give way.
If you cannot find the lever in the expected locations, check your owner's manual for the exact position. Some older vehicles or specialty cars place it elsewhere, and the manual will show you a diagram specific to your model.
Key Takeaways
- The bonnet release lever is inside the car, usually on the left side of the driver's seat, and has a bonnet symbol on the handle.
- After pulling the interior lever, you must go to the front of the car and push up on the secondary release catch under the bonnet edge.
- The bonnet will not open fully on its own — you need to locate and lift the support rod or prop to hold it open safely.
- Never work under an open bonnet without the support rod locked in place, as the bonnet can fall and cause injury.
- If the lever does not click or the bonnet does not budge, the release cable may be broken and will need professional repair.
Walk to the front of the car and locate the secondary catch
After pulling the interior lever, walk to the front of your vehicle. The bonnet will be slightly ajar — it will not swing open on its own. Look along the center of the bonnet's underside, just below the front edge where the bonnet meets the grille. You will see a small metal catch or latch.
Place your fingers under the bonnet edge and feel for this catch. It is usually a straightforward lever or hook that you push or lift to release the bonnet fully. Push or lift it gently — you do not need force. The bonnet should now be free to open.
Lift the bonnet and locate the support rod
Grip the bonnet on both sides and lift it slowly and steadily. As you raise it, look for a metal rod or prop attached to the underside of the bonnet or the engine bay frame. This rod prevents the bonnet from slamming shut and keeps it safely open while you work.
Most support rods are hinged at one end and have a hook or notch at the other. The hook end fits into a bracket on the bonnet's underside or the engine bay wall. Do not attempt to hold the bonnet open by hand — always use the support rod.
Insert the support rod into its bracket
Once the bonnet is raised to a comfortable working height, locate the bracket or slot where the support rod's hook end belongs. This is usually on the underside of the bonnet itself, toward the center, or on the engine bay frame. Lift the rod and guide its hooked end into the bracket with a gentle upward motion.
You should feel the rod settle into place with a slight click or resistance. The bonnet should now be held open firmly. If the rod does not stay in place, it may not be fully seated — lift it slightly and try again. Never proceed with work if the rod feels loose or unstable.
Close the bonnet when you are finished
To close the bonnet, lift it slightly to relieve pressure on the support rod, then unhook the rod from its bracket and lower it back to its resting position. Gently lower the bonnet by hand until it is about six inches from the frame, then release it to drop the final distance. It should latch automatically.
If the bonnet does not latch, push down firmly on the center of the bonnet until you hear a click. Do not slam it — a controlled closing prevents damage to the hinges and latch mechanism. Check that it is fully closed by trying to lift the bonnet slightly from the outside; it should not budge.
Troubleshooting common problems
If the interior lever pulls but nothing happens, the release cable may be broken or disconnected. This requires professional repair — do not force the lever or attempt to pry the bonnet open. If the secondary catch is stuck or corroded, spray it lightly with penetrating oil and wait a few minutes before trying again.
If the support rod is missing or damaged, do not open the bonnet. A falling bonnet can cause serious injury. Have the rod replaced before you attempt any engine bay work. If you are unsure whether the rod is find, close the bonnet and have a mechanic inspect it.
Frequently Asked Questions
What if the bonnet release lever is stuck and will not pull?
Spray the lever hinge and cable connection with penetrating oil and wait 10 to 15 minutes. Try pulling again with steady, moderate pressure — do not jerk or force it. If it remains stuck, the cable is likely broken and needs professional repair.
Can I hold the bonnet open without the support rod?
No. The bonnet is heavy and can fall suddenly, causing serious head or hand injury. Always use the support rod. If the rod is missing or broken, close the bonnet and have it repaired before working on the engine.
The secondary catch will not release — what do I do?
The catch may be corroded or stuck. Spray it with penetrating oil, wait a few minutes, and try again with gentle upward pressure. If it still will not budge, do not force it — have a mechanic release it to avoid damaging the mechanism.
Is there a different process for different car brands?
The basic steps are the same across most vehicles: interior lever, secondary catch, support rod. However, the exact location of the lever and catch varies by manufacturer. Your owner's manual shows the specific layout for your car.