You can replace most brake lights yourself in under 15 minutes with basic tools

A brake light replacement is one of the simplest car maintenance tasks you can do yourself. The process takes about 10 to 15 minutes, costs between $5 and $20 per bulb depending on your vehicle, and requires only a screwdriver or socket wrench — tools most people already have. You do not need to visit a mechanic or dealership unless your car has a sealed light assembly that cannot be opened without special equipment.

The steps are nearly identical across all vehicles: locate the burnt-out light from inside your trunk, remove the lens assembly or bulb holder, swap out the old bulb, and test it before closing everything back up. The main variables are where your brake lights sit, whether you access them from inside or outside the car, and what type of bulb your specific model uses.

Key Takeaways

  • Most brake light bulbs cost $5 to $20 and can be replaced in under 15 minutes without special tools.
  • You will need to know your vehicle's year, make, and model to buy the correct bulb type — check your owner's manual or a parts store.
  • Access the light from inside your trunk by removing the lens assembly or bulb holder, which usually twists or unscrews.
  • Test your brake lights before closing the trunk by having someone press the brake pedal while you watch the lights.

Locate the burnt-out brake light and gather your tools

Start by identifying which brake light is out. Have someone sit in the driver's seat and press the brake pedal while you stand behind the car and watch both lights. The brake lights are the two red lights at the rear corners of your vehicle — they sit above or near the taillights and glow when the brakes are applied.

Once you know which side is burnt out, open your trunk and look at the inside of the rear panel where the light assembly sits. You will see either a plastic lens that covers the bulb or a bulb holder that sticks out from the panel. Gather a screwdriver (usually Phillips head) or a socket wrench — check your owner's manual to see which tool fits your specific model. You will also need the correct replacement bulb, which you can find by looking up your vehicle's year, make, and model at any auto parts store or by checking your owner's manual.

Remove the lens assembly or bulb holder

The method depends on your car's design. Most vehicles have one of two setups: a lens assembly held on by bolts or screws from the outside, or a bulb holder that twists out from inside the trunk.

If you see screws or bolts around the edge of the red lens from outside the car, use your screwdriver or wrench to remove them — usually three to four fasteners per light. Once the screws are out, gently pull the lens assembly away from the car body. If you see a bulb holder protruding from the inside of the trunk panel, grip it firmly and twist it counterclockwise until it comes free. The bulb will either be attached to the holder or sitting loose inside a socket.

Remove the old bulb and install the new one

Once the lens or holder is out, locate the bulb. If it is attached to the holder, push it in slightly and twist it counterclockwise — it will pop out. If it is sitting loose in a socket, straightforward pull it straight out. Do not touch the glass part of the new bulb with your bare fingers, as oils from your skin can shorten its lifespan. Hold it by the metal base or use a clean cloth.

Insert the new bulb by pushing it straight into the socket or holder, then twist it clockwise until it stops. Do not force it — it should turn smoothly and seat firmly without excessive pressure. If you removed a lens assembly, reattach it by aligning the bolt holes and tightening the screws in a crisscross pattern (like tightening a wheel) to may support even pressure. If you removed a bulb holder, twist it clockwise back into the trunk panel until it is snug.

Test the brake light before finishing

Before you close the trunk, test the light to make sure it works. Have someone sit in the driver's seat and press the brake pedal while you watch the light you just replaced. It should glow red when ready and stay on as long as the pedal is held down. If it does not light up, the bulb may not be seated correctly — remove it and reinstall it, making sure it clicks or twists fully into place.

If the light still does not work after reinstalling the bulb, the socket itself may be damaged or corroded. Look inside the socket for discoloration, corrosion, or loose wires. If you see corrosion, you can try cleaning the socket contacts with a pencil eraser or fine-grit sandpaper, then reinstalling the bulb. If the socket is damaged or the wiring is loose, you will need to have a mechanic inspect it.

What to do if you cannot access the light assembly

Some vehicles, particularly newer models, have sealed light assemblies that cannot be opened without removing the entire assembly from the car body. If you remove the lens or bulb holder and find no access to the bulb, or if the assembly is glued shut, stop and take your car to a mechanic or dealership. Forcing a sealed assembly can crack the lens or damage the wiring, which will cost far more to repair than a professional replacement.

You can also check your owner's manual before you start — it will tell you whether your specific model has user-replaceable bulbs and show you the exact steps for your vehicle. If the manual says the light assembly is not user-serviceable, that is a reliable indicator that you should not attempt it yourself.

Frequently Asked Questions

How do I know what type of bulb to buy?

Check your owner's manual for the bulb type — it will list a code like 1157 or 7443. You can also take a photo of your current bulb and show it to an auto parts store employee, or look up your vehicle's year, make, and model on the store's website. The parts store will show you the correct bulb and often have it in stock.

Can I replace a brake light while the engine is running?

Yes, but turn off the engine first. The brake light assembly may be warm if the lights were recently on, so waiting a few minutes before touching it prevents burns. The engine does not need to run for this task.

What if the bulb keeps burning out after I replace it?

Repeated bulb failure usually means the socket is corroded or the wiring has a short circuit. Clean the socket contacts with an eraser or fine sandpaper and try a new bulb. If it burns out again within a few weeks, have a mechanic check the wiring and socket — a short can damage multiple bulbs and may indicate a larger electrical problem.

Do I need to remove the entire light assembly to replace the bulb?

Not usually. Most cars let you access the bulb from inside the trunk without removing the entire assembly. If you can twist out a bulb holder or unscrew a lens, you do not need to remove anything else. Only remove the full assembly if the manual says the bulb is not user-replaceable or if you cannot find any other way to reach it.