What you need to know before starting
Replacing a passenger door window on a 2013 Audi Q5 requires removing the door panel, unbolting the window regulator assembly, and installing a new glass pane. The job takes two to four hours for someone with basic mechanical experience and a socket set. You can do this yourself if you're comfortable working inside a car door, or you can take it to a shop — a dealership typically charges $400 to $600 in labor alone, while an independent shop may charge $250 to $400.
The window itself (the glass pane) costs $150 to $300 depending on whether you buy OEM Audi glass or aftermarket. The regulator — the mechanical assembly that moves the window up and down — costs $200 to $400 if it also needs replacement. Most DIY jobs involve just the glass; the regulator usually lasts the life of the car unless the window has been stuck or forced.
Key Takeaways
- You will need a door panel removal tool, a socket set, a screwdriver set, and a new window pane; the regulator assembly may also need replacement if the window was stuck or damaged.
- The first step is always to remove the door panel by unclipping the trim pieces and unbolting the panel from inside the door frame.
- Once the panel is off, you can access the window regulator bolts and the rubber gasket holding the glass; unbolt the regulator and slide the glass out.
- A new window pane costs $150 to $300 and a regulator costs $200 to $400; labor at a shop runs $250 to $600 depending on whether the regulator also needs work.
- If the regulator is broken (window won't move or moves slowly), you must replace it along with the glass, which doubles the job time and parts cost.
Gather your tools and parts before you start
You will need a door panel removal tool (a plastic pry bar, about $8 to $15), a socket set with 10mm and 13mm sockets, a Phillips and flat-head screwdriver, and a pair of work gloves. Have a clean cloth or towel ready to catch any water or debris that falls out of the door cavity.
Order your replacement window pane before you begin. Call a Audi dealership parts department or an online auto glass supplier with your VIN and ask for the passenger front door window for a 2013 Q5. Confirm whether you need the regulator as well — if the window moves smoothly but the glass is cracked or shattered, you only need the pane. If the window is stuck, moves slowly, or makes grinding sounds, the regulator is likely damaged and must be replaced.
Some people use a windshield replacement shop instead of ordering parts separately. These shops can often come to your home or workplace and install a new window in place, which saves you the labor of removing the door panel. Call ahead to confirm they work on Audi Q5 door windows and ask for a quote.
Remove the door panel to access the window assembly
Park on a level surface and open the passenger door fully. Look along the inside edge of the door panel (the plastic trim facing the interior of the car) for clips and bolt holes. You will see two or three bolts along the bottom edge of the panel, usually covered by a rubber trim strip. Use your socket set to remove these bolts and set them aside in a small container so you don't lose them.
Next, locate the clips holding the panel to the door frame. These are plastic tabs along the top and sides of the panel. Use your door panel removal tool to gently pry the panel away from the frame, starting at a corner. Work slowly around the perimeter — the clips will pop free with a click. Once all clips are released, carefully pull the panel away from the door and set it aside on a clean surface. Be gentle; the panel has wiring for the window switch and door lock, which you may need to disconnect if you're removing it completely.
If the wiring is still connected and you only need to access the window area, you can leave the panel partially attached and just pull it back enough to see inside the door cavity. This saves time if you're only replacing the glass.
Unbolt the window regulator and remove the old glass
With the door panel removed or pulled back, you can now see the window regulator — a metal frame with bolts and a motor that moves the window up and down. Look for three or four bolts holding the regulator to the inside of the door frame. Use your socket set to remove these bolts. The regulator will come free, but the glass pane is still held in place by a rubber gasket around its edges.
Locate the rubber gasket (a black rubber channel) that runs around the perimeter of the window opening. This gasket holds the glass in place. You can either pry the gasket out carefully with a flat-head screwdriver and reuse it, or cut it away if you're installing a new one. If you're reusing it, work slowly to avoid tearing it. Once the gasket is loose, carefully slide the old glass pane out of the door opening. It will be heavy and may have sharp edges if it's broken, so wear gloves and be cautious.
If the regulator is also being replaced, this is the time to install the new one. Slide the new regulator into place, align the bolt holes, and tighten the bolts with your socket set. If you're only replacing the glass, you can leave the old regulator in place and proceed to the next step.
Install the new window pane and reassemble
Before installing the new glass, inspect the rubber gasket. If it's cracked, hardened, or torn, replace it with a new one (gaskets cost $20 to $40). If it's still pliable and intact, you can reuse it. Slide the new glass pane into the gasket channel, making sure it sits evenly in the opening. The glass should slide smoothly and sit flush with the door frame.
Once the glass is in place, reinstall the window regulator if you removed it. Align the bolts and tighten them firmly with your socket set. Test the window by turning on the car and using the switch to move the window up and down a few times. It should move smoothly without grinding or sticking. If it does, stop and check that the regulator bolts are tight and the glass is seated correctly in the gasket.
After testing, carefully reattach the door panel by aligning the clips and pushing the panel back into place until you hear the clips click. Reinstall the bolts along the bottom edge and tighten them with your socket set. Reconnect any wiring if you disconnected it. Test the door lock and window switch one more time to confirm everything works.
When to take it to a shop instead
If the window is broken and you're not comfortable working inside a car door, a glass shop or dealership can handle the entire job. Windshield replacement shops often do door windows and may charge less than a dealership. Call ahead with your VIN and ask whether they can do a passenger door window on a 2013 Q5 and what they charge.
You should also take it to a shop if the regulator is broken. While the regulator can be replaced at home, it requires more time and mechanical skill than just swapping the glass. A shop can diagnose whether the regulator is the problem and replace both the glass and regulator in one visit, which is often faster and less frustrating than doing it yourself if you're not experienced.
If you're unsure whether the regulator is damaged, describe the problem to the shop: Is the window stuck? Does it move slowly or make noise? Does it fall down on its own? These details help the shop know what to expect before they start work.
Frequently Asked Questions
Can I replace just the glass without removing the door panel?
No. The glass is held in place by a rubber gasket that runs along the inside of the door frame, and you must access this gasket from inside the door cavity. Removing the door panel is the only way to reach it. The job is not difficult, but it is necessary.
What if the window regulator is broken — can I just replace the glass?
If the regulator is broken, replacing only the glass will not fix the problem. The window will still not move, or it will move slowly or unevenly. You must replace the regulator as well. A shop can diagnose this by testing the window before you pay for parts.
How long does this job take if I do it myself?
Plan on two to four hours if you're doing it for the first time and have basic mechanical experience. The door panel removal usually takes 30 to 45 minutes. Unbolting the regulator and removing the old glass takes another 30 minutes. Installing the new glass and reassembling takes one to two hours. If you've done this before, you can finish in under two hours.
Is OEM Audi glass better than aftermarket glass?
OEM Audi glass is made to Audi's specifications and fits perfectly. Aftermarket glass is usually made by a third-party supplier and costs less, but quality varies. Both should work fine. Ask the parts supplier whether the glass is tinted to match your car and whether it includes the gasket.
What if I crack the new glass while installing it?
Handle the glass carefully and wear gloves to avoid dropping it. If you do crack it, most suppliers will exchange it if you return it within a few days. Keep your receipt and ask about their return policy before you buy.