When and why your wiper motor fails

A windshield wiper motor burns out when the internal brushes wear down, the gearbox seizes, or the electrical connections corrode. You'll notice the wipers stop moving even though you hear the motor running, or they move very slowly, or they don't park at the bottom of the windshield when you turn them off. Sometimes the motor makes a grinding noise before it fails completely.

The motor typically lasts 3 to 5 years depending on how often you use the wipers and whether you live in a wet climate. Salt air and road spray accelerate corrosion. If your wipers worked fine yesterday and today they don't move at all, the problem is usually the motor itself, not the wiper blades or the switch.

Replacing the motor is a job most owners can do at home with basic tools. It takes 30 minutes to an hour. The motor sits under the hood near the base of the windshield and bolts to the firewall — the metal wall between the engine and the cabin.

Key Takeaways

  • A failed wiper motor makes noise but the wipers don't move, or moves them very slowly, and you can confirm this by turning the wipers on and listening under the hood.
  • You need the correct replacement motor for your vehicle year and model, which you can find by entering your vehicle information at an auto parts store or online.
  • The motor bolts to the firewall under the hood and connects to the wiper linkage with a single clip or bolt that you remove before pulling the motor out.
  • Disconnecting the battery before you start prevents accidental electrical shorts and is the safest first step.
  • The whole job requires only a socket wrench set, a screwdriver, and a clip removal tool or small pry bar — no special equipment.

Gather the right parts and tools

Before you start, you need the correct wiper motor for your vehicle. Go to an auto parts store with your vehicle's year, make, and model, or order online using that information. The motor is specific to your car — a motor for a 2015 Honda Civic will not fit a 2015 Toyota Corolla. The part number is usually printed on the old motor, so you can also photograph it and search online.

Tools you'll need: a socket wrench set (usually 8mm to 13mm sockets), a Phillips or flathead screwdriver depending on your vehicle, and a small pry bar or clip removal tool to disconnect the wiper linkage. Most people have these already. You do not need a power drill or impact wrench.

Gather a small container to hold the bolts and clips so you don't lose them. Have a clean rag nearby to wipe away any grease or debris from the motor housing.

Disconnect the battery and locate the motor

Open the hood and locate the negative terminal on your battery — it has a black cap and a minus sign. Loosen the nut on the negative cable with a wrench and slide the cable off the terminal. This prevents electrical shorts while you work. Leave the cable disconnected until you finish the job.

Look at the base of the windshield on the driver's side, just above the firewall. You'll see a black plastic or metal housing with two or three bolts holding it to the firewall. This is the wiper motor assembly. Trace the wiper linkage — the metal rod that connects the motor to both wiper arms — and locate the clip or bolt where it attaches to the motor shaft.

Some vehicles have the motor on the passenger side instead. Check your owner's manual or look at both sides of the windshield base if you're not sure which side yours is on.

Remove the wiper linkage connection

The wiper linkage connects to the motor shaft with either a clip or a single bolt. If it's a clip, use a small pry bar or clip removal tool to gently pry it upward and slide it off the shaft. If it's a bolt, use the appropriate socket wrench to remove it. Place the clip or bolt in your container.

Once the linkage is disconnected, gently move the linkage to the side so it doesn't get in your way. You may need to move it slightly to access the motor bolts. Do not force it — if it feels stuck, check that you've removed the clip or bolt completely.

Unbolt the motor from the firewall

The motor housing is held to the firewall with two or three bolts, usually 10mm or 11mm. Use the correct socket wrench to remove each bolt and place them in your container. Once all bolts are out, the motor will be loose but still connected electrically.

Gently pull the motor toward you to expose the electrical connector on the back. The connector is usually a plastic plug with two or three wires. Press the release tab on the connector — it's usually a small plastic lever or button — and slide the connector off the motor terminals. If there's no release tab, gently wiggle the connector side to side while pulling it straight out.

Now you can lift the motor completely out of the engine bay. Set it aside in a safe place where it won't roll or tip over.

Install the new motor and reconnect everything

Take the new motor and position it where the old one was, with the shaft pointing toward the wiper linkage. Slide the electrical connector onto the new motor terminals until it clicks or seats fully. Push firmly — a loose connection will cause the wipers to fail again.

Insert the bolts through the motor housing and into the firewall holes. Tighten each bolt with the socket wrench in a cross pattern — if there are three bolts, tighten top, then bottom-left, then bottom-right — to may support even pressure. Tighten firmly but do not over-tighten, which can crack the plastic housing.

Reconnect the wiper linkage by sliding the clip back onto the motor shaft and pressing it down until it seats, or by inserting the bolt and tightening it with the socket wrench. The linkage should move freely when you wiggle it by hand.

Test the new motor before closing the hood

Reconnect the negative battery cable by sliding it back onto the battery terminal and tightening the nut. Do not start the engine yet. Turn the ignition key to the "On" position without starting the engine, then turn on the windshield wipers. The wipers should move smoothly from bottom to top and back down, and they should park at the bottom when you turn them off.

If the wipers don't move, turn off the wipers and check that the electrical connector is fully seated on the motor. If they move but very slowly, the motor may be defective — contact the auto parts store where you bought it for a return or exchange.

If everything works correctly, close the hood and you're done. The job is complete.

Frequently Asked Questions

Can I replace the wiper motor without disconnecting the battery?

Technically yes, but disconnecting it is safer. If you accidentally touch a live wire or metal part to the motor housing, you could short the electrical system or damage the new motor. It takes 30 seconds to disconnect and reconnect the battery, so it's worth doing.

What if the wiper linkage won't come off the motor shaft?

The clip may be stuck from corrosion or dirt. Spray a small amount of penetrating oil like WD-40 around the base of the clip, wait five minutes, then try again with the pry bar. If it still won't budge, tap the pry bar gently with a hammer to work the clip loose. Do not hammer hard — you can bend the linkage.

Do I need to replace the wiper linkage at the same time?

No. The linkage is a separate part and usually lasts much longer than the motor. Replace it only if it's bent, cracked, or won't move smoothly after the new motor is installed.

How do I know if the problem is the motor and not something else?

Turn on the wipers and listen under the hood. If you hear the motor running but the wipers don't move, the motor is bad. If you hear nothing at all, the problem may be the wiper switch, a blown fuse, or a wiring issue — check the fuse box first before replacing the motor.

Can I drive the car with a broken wiper motor?

Yes, but you should not drive in rain or snow without working wipers. A broken motor is a safety issue. Most auto parts stores have the motor in stock, so you can usually replace it the same day you discover it's broken.