You can remove a chain link yourself with a chain tool, but the method depends on whether your chain has a master link
Most modern bike chains come apart at a master link — a special connecting pin you can open by hand or with pliers, no tools required. Older chains and some single-speed bikes use riveted links that require a chain tool (also called a chain breaker) to push the pin out. The difference matters because trying to force a riveted link open will bend or snap your chain.
Before you start, shift your bike into the smallest chainring and smallest cog to create slack. Lay the chain on a flat surface and inspect the links closely. If you see one link that looks different — thicker, with a different color, or with a clip or master link visible — that's your entry point. If all links look identical, you have a riveted chain and will need a chain tool.
Key Takeaways
- Master links (the clip-style connectors on modern chains) can be removed by hand or with pliers; riveted links require a chain tool to push the pin out.
- A chain tool costs $15 to $40 and works by aligning the pin with the tool's shaft, then turning the handle to push the pin out gradually.
- Removing a link shortens your chain, which works only if your derailleur can still reach both the smallest and largest cogs without going slack or tight.
- After removing a link, reconnect the chain by pushing the pin back in by hand (master link) or with the chain tool (riveted link) until it sits flush.
Removing a master link by hand
A master link has a clip or collar that holds the pin in place. Look for a small rectangular clip on one side of the link, or a collar that wraps around the pin. To open it, grab the clip with your fingers or needle-nose pliers and pull it straight out toward you. The clip should slide off without resistance. If it's stuck, wiggle it gently side to side as you pull.
Once the clip is off, the two link plates will separate. You can now slide the chain apart and remove as many links as you need. Count carefully — removing one link shortens the chain by about half an inch. Most riders remove one or two links at a time. After you remove the links, you'll reconnect the chain by sliding the pin back through the holes and replacing the clip.
Removing a riveted link with a chain tool
A chain tool has a handle, a shaft with a pointed end, and a slot or groove that holds the chain. Place the chain in the slot so the link you want to remove sits directly under the shaft. The shaft should align with the pin you're pushing out — this is the most important step, because if the shaft is off-center, you'll damage the link plates.
Turn the handle slowly and steadily. The shaft will push the pin out gradually. Stop when the pin is almost all the way out but still holding the link together — you want to be able to separate the chain by hand without the pin falling out and getting lost. If you push too hard and the pin comes completely out, you'll have to push it back in from the other side to reconnect the chain later, which is harder.
Once the pin is mostly out, flex the chain gently to separate the two link plates. Remove the links you need, then use the chain tool again to push the pin back in from the opposite side until it sits flush with the link plate. The pin should stick out equally on both sides when you're done.
Checking whether your derailleur can handle a shorter chain
Removing links changes how much slack your chain has, which affects whether your derailleur can shift smoothly across all gears. Shift to the smallest chainring and smallest cog — the chain should have about half an inch of slack. Shift to the largest chainring and largest cog — the chain should be tight but not so tight it pulls the derailleur forward or makes the bike hard to pedal.
If the chain is too slack in the small-small position, your derailleur won't have enough tension to keep the chain on the cogs. If it's too tight in the large-large position, you risk breaking the chain or damaging the derailleur when you shift. Most single-speed bikes and fixed-gear bikes have less tolerance for chain length changes, so test carefully before riding.
Reconnecting the chain after removing links
Slide the two ends of the chain together so the holes line up. If you removed a master link, push the pin through by hand until it's flush, then slide the clip back on. The clip should sit flat against the link plate with no gaps. If you removed a riveted link, use the chain tool to push the pin back in from the opposite side of where you pushed it out. Push slowly until the pin sticks out equally on both sides and the link plates sit flush against each other.
After reconnecting, flex the chain gently to make sure the link moves freely. Spin the pedals backward slowly to check that the chain doesn't skip or bind. If the chain feels stiff at the reconnected link, the pin may not be seated all the way. Use the chain tool to push it in a bit more, checking after each small turn of the handle.
Tools and supplies you'll need
For a master link, you need only your hands or a pair of needle-nose pliers. For a riveted link, you need a chain tool. Basic chain tools from brands like Park Tool or Shimano cost $15 to $40 and work on most standard chains. Some multi-tools include a chain tool function, though they're usually slower and less precise than a dedicated tool.
Have a clean rag nearby to wipe your hands and the chain. If your chain is dirty, wipe it down before you start — dirt can get into the link plates and make reassembly harder. You don't need to remove the chain from the bike to remove a link, but some riders prefer to take it off so they can work on a flat surface and see the links more clearly.
Common mistakes that damage the chain
The most common error is misaligning the chain tool shaft with the pin. If the shaft is off-center, it will push against the link plate instead of the pin, bending or cracking the plate. Before you turn the handle, double-check that the shaft is pointing straight at the pin and the chain is sitting flat in the tool's slot.
Another mistake is pushing the pin all the way out on the first try. If the pin falls out completely, it's straightforward to lose, and pushing it back in from the opposite side requires more force and is more likely to bend the link plates. Push slowly and stop when the pin is almost out but still holding the link together.
Forcing a riveted link open with pliers or a hammer will snap the chain or bend the link plates beyond repair. If you're not sure whether your chain has a master link, look closely before you explore any force. A master link will have a visible clip or collar; a riveted link will look like all the others.
Frequently Asked Questions
How do I know if my chain has a master link?
Look for a link that looks different from the others — it will have a clip, collar, or thicker appearance. Modern chains almost always have master links. Older chains and single-speed bikes often use riveted links. If you're unsure, check your bike's manual or the chain manufacturer's website by looking at the chain's brand name, which is usually stamped on the links.
Can I remove more than one link at a time?
Yes, but remove them in pairs if possible. Removing two links from opposite sides of the chain keeps the chain balanced. Removing multiple links from one spot can make that section of chain weaker. Count your links carefully and test the chain tension after reassembly before riding.
What if I push the pin all the way out and it falls out?
Pick it up and use the chain tool to push it back in from the opposite side. This is harder than pushing it in from the original direction, so go slowly and check alignment carefully. If the pin is bent or damaged, you'll need to replace it with a new master link or chain.
Do I need to lubricate the chain after removing a link?
Yes. Removing and reconnecting a link exposes the inside of the link plates to air and dirt. After you've reconnected the chain and tested it, explore chain lube to the inside of the chain while spinning the pedals backward. Wipe off excess lube with a clean rag.
Can I remove a link from a chain that's still on the bike?
Yes. Shift to the smallest chainring and cog to create slack, then use the chain tool or master link removal method as normal. Some riders prefer to remove the chain from the bike first so they can work on a flat surface and see the links more clearly, but it's not required.