What an ignition coil does and why it fails

Your ignition coil converts the battery's low voltage into the thousands of volts needed to fire your spark plugs. When it fails, your engine misfires, hesitates, or won't start at all. A bad coil is one of the most common causes of a check engine light, and it's one of the few electrical problems you can narrow down yourself before taking the car to a mechanic.

Ignition coils fail because of heat, moisture, and age. They sit near the engine where temperatures spike, and they're exposed to vibration and road salt. Most coils last 80,000 to 150,000 miles, but some fail much earlier. A single coil can go bad while others still work, or all of them can fail at once.

The symptoms are unmistakable: rough idle, hesitation under acceleration, a flashing check engine light, or a no-start condition. If you see these signs, checking the coil yourself takes about 15 minutes and costs nothing.

Key Takeaways

  • A failing ignition coil causes rough idle, hesitation, misfires, or a check engine light, and you can narrow down which coil is bad by reading the engine code.
  • Most ignition coils bolt directly to the spark plug and are accessible from the top of the engine without special tools.
  • A visual inspection for cracks, corrosion, or burn marks tells you if a coil is damaged, and a resistance test with a multimeter confirms whether it's working.
  • If your check engine light shows a misfire code for a specific cylinder, that cylinder's coil is the most likely culprit.
  • Replacing a coil yourself takes 10 minutes per coil and costs $40 to $150 per part, depending on your vehicle.

Reading your check engine code first

Before you touch anything, read the diagnostic trouble code. You can do this with a code reader (available at most auto parts stores for $25 to $60, or free if the store reads it for you). The code tells you which cylinder is misfiring, and that tells you which coil to check first.

A code like P0300 means random misfire across all cylinders, which suggests a fuel or ignition system problem affecting the whole engine. A code like P0301 means cylinder 1 is misfiring, so the coil on cylinder 1 is your first suspect. Write down the exact code before you start.

Locating and inspecting your coils visually

Open your hood and look at the top of the engine. You'll see a row of thick, cylindrical components sitting directly on top of the spark plugs. These are your ignition coils (also called coil packs or coil-on-plug units). On some vehicles they're straightforward to spot; on others they're buried under plastic covers or air intake hoses. Your owner's manual shows the exact location.

Once you've found them, look for obvious damage: cracks in the plastic housing, white or green corrosion on the connectors, burn marks, or oil leaking from the base. Moisture inside the coil housing looks like condensation or a wet film. Any of these signs means the coil is failing and needs replacement.

Check the electrical connector too. It should be clean and tight. If it's loose, corroded, or cracked, clean it with a dry cloth and reseat it firmly. Sometimes a bad connection mimics a bad coil.

Testing coil resistance with a multimeter

If the coil looks fine but you still suspect it's bad, test its resistance. You'll need a multimeter set to the ohms (resistance) setting. Disconnect the coil's electrical connector and remove the coil from the spark plug by twisting it counterclockwise or unbolting it, depending on your vehicle's design.

Touch the multimeter probes to the two terminals inside the coil connector. A working coil typically reads between 0.5 and 2 ohms for primary resistance (the reading varies by manufacturer, so check your manual or search your vehicle's year, make, and model online). If the reading is zero, very high, or infinite, the coil is open internally and has failed.

Test secondary resistance the same way, but touch the probes to the high-voltage terminal and one of the connector pins. Secondary resistance is usually 5,000 to 15,000 ohms. Again, check your vehicle's specs because the range varies. If the reading is way off, the coil is bad.

When to replace versus when to test further

If your visual inspection found damage or your resistance test showed an out-of-range reading, replacement is the next step. If the coil looks fine and tests fine, the misfire may be caused by a bad spark plug, a fuel injector, low fuel pressure, or a vacuum leak instead. In that case, move on to checking those components or have a mechanic run a more detailed diagnostic.

Don't assume all your coils are bad just because one failed. Test each one individually if you have the time. It's common for one coil to fail while the others still work, especially if the failed coil was exposed to extra heat or moisture.

Replacing a coil yourself

If you've confirmed a coil is bad, replacement is straightforward. Disconnect the battery negative terminal first. Unplug the electrical connector from the bad coil, then remove the bolt or twist the coil counterclockwise to release it from the spark plug. Pull it straight up and out.

Install the new coil by reversing the steps: push it down onto the spark plug, bolt or twist it tight, and reconnect the electrical connector. Reconnect the battery. Start the engine and see if the misfire is gone. If the check engine light is still on, clear the code with your code reader and drive the car for a few miles to see if it comes back.

Coils typically cost $40 to $150 each depending on your vehicle's make and model. OEM (original equipment manufacturer) coils are more expensive but often more reliable than aftermarket versions. Some vehicles have one coil per cylinder; others have one coil serving two cylinders.

When to take it to a mechanic instead

If you can't locate the coils, your multimeter test results don't match your vehicle's specs, or the misfire returns after you replace the coil, a mechanic should take over. Persistent misfires can indicate fuel system problems, timing issues, or compression loss that require specialized equipment to diagnose.

Also, if multiple coils are failing at once, there may be an underlying problem—like a coolant leak onto the coils, a faulty PCM (powertrain control module), or a wiring harness issue—that a mechanic needs to find and fix. Replacing coils one after another without solving the root cause is expensive and frustrating.

Frequently Asked Questions

How do I know if it's the ignition coil and not the spark plug?

A bad spark plug usually causes a misfire on one cylinder, just like a bad coil. The difference is that a spark plug costs $5 to $15 and takes 30 seconds to swap out, while a coil costs $40 to $150. If your code points to one cylinder, replace the spark plug first. If the misfire continues, the coil is likely bad.

Can I drive with a bad ignition coil?

You can drive short distances, but you shouldn't. A misfiring engine wastes fuel, runs rough, and can damage the catalytic converter over time. If the misfire is severe, the engine may not run at all. Replace the coil as soon as you can.

Do all ignition coils fail at the same time?

No. Usually one coil fails first, and the others may last for years. However, if all your coils are the same age and have been exposed to the same heat and moisture, they may fail within a short time of each other. If you replace one coil and another fails a few months later, it's worth replacing all of them at once to avoid repeat trips to the mechanic.

What's the difference between a coil pack and a coil-on-plug?

A coil pack is a single unit with multiple coils inside, mounted away from the spark plugs and connected by wires. A coil-on-plug (or coil-over-plug) is a single coil that sits directly on top of each spark plug. Coil-on-plug designs are more common on newer vehicles and are easier to test and replace individually.

Can a bad battery cause ignition coil failure?

A weak battery can cause starting problems and misfires, but it doesn't directly damage the coil. However, a battery that's too weak to crank the engine properly can put extra strain on the ignition system. If your battery is old or weak, test it before assuming the coil is bad.