A Kubota track skid steer is a compact loader with rubber or steel tracks instead of wheels, built for rough terrain and tight spaces where a wheeled machine would sink or slip.
Kubota manufactures these machines primarily for landscaping, construction, and property maintenance work. The track design spreads the machine's weight over a larger surface area, which means it can operate on soft ground, mud, or snow without leaving deep ruts. The compact size — typically 10 to 14 feet long — lets you work in confined areas like residential yards, between trees, or inside buildings under renovation.
If you own a Kubota track skid steer or are considering renting or buying one, understanding its maintenance needs and capabilities will help you keep it running and know what jobs it can actually handle. This guide covers the machine itself, what maintenance matters most, and how to decide if one is the right tool for your situation.
Key Takeaways
- Kubota track skid steers use rubber or steel tracks to distribute weight and operate on soft ground where wheeled loaders would sink.
- The compact size makes them useful for landscaping, site cleanup, and demolition work in tight spaces, but they have lower lift capacity than larger machines.
- Track machines require regular inspection of the tracks themselves, including tension adjustment and cleaning out debris that can cause premature wear.
- Hydraulic fluid, engine oil, and air filters need more frequent changes on track machines because they work harder in dusty or muddy conditions.
- Rental costs typically run $200 to $400 per day depending on your region and whether you need a machine with a bucket, grapple, or other attachment.
How Kubota track skid steers differ from wheeled loaders
The main difference is traction and ground pressure. A wheeled skid steer concentrates its weight on four small contact patches, which works fine on pavement or compacted soil but can sink into mud, sand, or snow. A track machine spreads that same weight across the entire length of each track, lowering ground pressure significantly. Kubota's track models can operate on surfaces that would bog down a wheeled machine.
Track machines also turn differently. A skid steer (wheeled or tracked) steers by running one side faster than the other, which causes it to pivot. On tracks, this pivot is smoother and causes less turf damage than on wheels, because the tracks are already in contact with the ground across their full length. On soft ground, a wheeled machine can tear up grass or leave visible ruts; a track machine distributes the turning force more evenly.
The trade-off is speed and fuel efficiency. Track machines are slower than wheeled ones and burn more fuel to move the same distance, because the tracks create more rolling resistance. They also cost more to buy and repair, and track replacement is a major expense — typically $2,000 to $4,000 per pair depending on the model and whether you choose rubber or steel.
Maintenance tasks specific to track machines
Track tension is the single most important maintenance item. Tracks that are too loose will slip off or wear unevenly; tracks that are too tight will overheat and fail prematurely. Kubota specifies the correct tension in your operator's manual, usually measured by how much the track deflects when you push on it with your hand. Check tension every 50 operating hours, and adjust it using the idler wheel bolts on the rear of each track. This is not a job for someone unfamiliar with the machine — if you are unsure, have a dealer do it.
Clean the tracks and undercarriage after every use, especially if you have been working in mud or clay. Dried mud hardens and can jam the track rollers, and it adds weight that strains the drive system. Use a pressure washer on low setting (below 2,000 PSI) to avoid forcing water into sealed bearings. Pay special attention to the spaces between the track and the frame, where debris collects.
Inspect the track for cracks, missing lugs, or bent sections every week if you use the machine regularly. Small cracks can be welded, but a severely damaged track must be replaced. Bent sections usually mean the track has hit a rock or root hard enough to damage the internal structure, and continuing to run on it will destroy the rollers and idler wheel.
Engine and hydraulic system care
Kubota track skid steers run either diesel or gasoline engines, depending on the model. Diesel engines are more common because they deliver better torque and fuel economy, but they require more careful maintenance. Change the engine oil and filter every 250 operating hours or every six months, whichever comes first. Track machines work in dusty conditions, so the air filter may need changing more often than the manual suggests — check it monthly and replace it if it looks clogged.
The hydraulic system powers the tracks, boom, and any attachments. Hydraulic fluid breaks down faster in track machines because they work harder and generate more heat. Check the hydraulic fluid level before each use, and change the hydraulic filter every 500 operating hours. If the machine starts moving slowly or the boom lifts sluggishly, the hydraulic filter is likely clogged. A clogged filter forces the pump to work harder, which shortens its life and can cost $1,500 to $3,000 to replace.
Keep the hydraulic fluid clean. Dirt in the system causes internal leaks and premature wear on cylinders and motors. If you need to top off the hydraulic fluid, use only the type specified in your manual — mixing hydraulic fluids can cause sludge buildup. Store hydraulic fluid in a sealed container away from moisture, and never leave the hydraulic reservoir cap off for more than a few minutes.
Attachment maintenance and compatibility
Kubota track skid steers accept a wide range of attachments: buckets, grapples, forks, augers, and brooms. Each attachment has its own weight and load rating. Exceeding the machine's lift capacity will strain the hydraulic system and boom cylinders. Check the attachment's weight and the machine's rated capacity before using it — the capacity is listed on a plate on the frame and in your operator's manual.
Hydraulic hoses on attachments can leak or rupture, especially if they are old or have been kinked. Inspect all hoses before each use, looking for cracks, bulges, or wet spots. A leaking hose will lose hydraulic pressure, causing the attachment to move slowly or fail entirely. Hose replacement is inexpensive (usually $50 to $200 per hose), but a ruptured hose spraying hot hydraulic fluid can cause serious injury.
Clean attachment connection points after each use. Hydraulic quick-couplers can jam if dirt gets into them, and a stuck coupler can be difficult and expensive to repair. Wipe the male and female ends with a clean cloth before connecting or disconnecting an attachment.
When to rent versus buy a Kubota track skid steer
Rental makes sense if you need the machine for a specific project lasting a few days or weeks. Daily rental rates vary by region and machine size, but expect to pay $200 to $400 per day for a standard Kubota track skid steer. Weekly rates are usually 2.5 to 3 times the daily rate, and monthly rates are 8 to 10 times the daily rate. If you need the machine for more than three or four months per year, buying may be cheaper than renting.
Buying a new Kubota track skid steer costs $35,000 to $60,000 depending on the model and attachments. Used machines range from $15,000 to $40,000 depending on age, hours, and condition. Ownership costs include fuel, maintenance, storage, and insurance. If you buy, budget for a major repair (engine overhaul, hydraulic pump replacement, or track replacement) every 2,000 to 3,000 operating hours, which could cost $3,000 to $8,000.
Rental companies handle maintenance and repairs, so renting shifts that burden to them. However, rental machines are often used hard and may not be as well-maintained as a machine you own. If you rent, inspect the machine before you take it and report any damage or mechanical issues in writing before you leave the lot.
Common problems and how to prevent them
Track slippage is the most common complaint. If the tracks slip when you try to move forward or turn, the tracks are either too loose or the ground is too slippery. Tighten the tracks first. If slippage continues on normal ground, the track drive motor may be failing, which requires dealer service. On ice or very slippery surfaces, slippage is normal and you straightforward cannot work safely — stop and wait for conditions to improve.
Hydraulic leaks often start small and go unnoticed until the system loses pressure. Check underneath the machine weekly for wet spots or drips. A small leak at a hose connection can usually be fixed by tightening the fitting; a leak at a cylinder rod seal requires the cylinder to be rebuilt or replaced. Catching leaks early saves money and prevents breakdowns in the middle of a job.
Engine overheating happens when the radiator is clogged with dust or mud. Clean the radiator fins with compressed air or a soft brush every week, especially if you work in dusty conditions. Never use a pressure washer on the radiator itself, because high pressure can bend the fins and reduce cooling efficiency. If the engine temperature gauge climbs into the red zone, stop when ready and let the engine cool before investigating.
Frequently Asked Questions
Can a Kubota track skid steer work on pavement?
Yes, but rubber tracks will wear faster on hard surfaces. Steel tracks can damage pavement and should be avoided on asphalt or concrete. If you need to work on pavement regularly, rent or buy a wheeled skid steer instead, which is designed for that use and will cost less to operate.
How deep can a track skid steer dig?
Kubota track skid steers are not designed for digging. They are loaders, not excavators. A standard bucket can scrape and move material, but the boom cannot reach deep into the ground the way an excavator's arm can. For digging trenches or holes, you need an excavator.
What is the difference between rubber and steel tracks?
Rubber tracks are quieter, cause less ground damage, and are better for finished surfaces or landscaping work. Steel tracks grip better in mud and snow, last longer, and cost less to replace, but they are loud, damage pavement, and are heavier. Choose rubber for residential or landscaping jobs; choose steel for demolition or heavy construction work.
Do I need a special license to operate a Kubota track skid steer?
No federal license is required, but some states and municipalities have their own rules. Check with your local building department or equipment rental company before you operate one on a job site. Many construction sites require OSHA training or a certificate of competency, even though it is not legally mandated everywhere.
How often should I grease the track components?
Kubota track machines have sealed bearings that do not require regular greasing. However, the idler wheel bolts, boom pivot points, and attachment connection points should be greased every 250 operating hours. Use a grease gun with the type of grease specified in your manual — using the wrong grease can cause seals to swell or shrink and fail.