What the Lippert Auto Level does and why you might need to reset it
The Lippert Auto Level is a hydraulic leveling system found on many RVs and motorhomes. It automatically extends and retracts jacks to keep your vehicle level when parked, which matters because an unlevel RV can damage appliances, cause water and propane to flow the wrong way, and make living inside uncomfortable or unsafe.
A reset becomes necessary when the system loses its memory of where the jacks should be—usually after a battery disconnect, a blown fuse, or a control panel malfunction. When this happens, the jacks may not extend or retract at all, or they may move erratically. A reset tells the system to relearn its starting position and calibrate itself again.
This is different from a repair. You are not fixing a broken component; you are restoring the system's ability to remember and respond to commands. Most owners can do this without a technician, though the exact steps depend on which Lippert control panel you have.
Key Takeaways
- A Lippert Auto Level reset clears the system's memory and forces it to recalibrate, which often fixes jacks that won't move or move unpredictably.
- The reset process varies by control panel model—check your RV manual or the panel itself to identify which version you own.
- Most resets involve holding a button for several seconds or cycling power to the system, and take less than five minutes to complete.
- If the jacks still do not respond after a reset, the problem is likely a blown fuse, dead battery, or hydraulic failure that requires professional diagnosis.
Identifying your Lippert control panel model
Lippert makes several versions of the Auto Level control panel, and the reset procedure is different for each one. The most common models in residential RVs are the Lippert Ground Control, the Lippert Solera, and the older Lippert Command Center. Some newer RVs use the Lippert iCommand app-based system.
Find your panel by looking inside your RV near the main electrical panel or in a cabinet near the driver's seat. The model name is usually printed on the face of the panel or on a label on the back. If you cannot locate it, check your RV's owner manual—it will list the leveling system by name and often include the reset steps specific to your model.
Once you know which panel you have, the reset process takes only a few minutes. Write down the model name before you start, because you will need it to find the correct procedure.
Reset steps for Lippert Ground Control and Solera panels
The Lippert Ground Control and Solera panels use a similar reset method. Locate the power switch on the panel—it is usually labeled "On/Off" or "Power." Turn the switch to the Off position and leave it off for at least 10 seconds. This clears the system's memory.
After 10 seconds, turn the power back on. The panel will go through a startup sequence, and you may hear the hydraulic pump set up briefly. This is normal. Once the startup is complete, the panel should display its normal operating screen. At this point, press and hold the "Level" or "Auto" button for 3 to 5 seconds. The system will begin a calibration cycle, during which the jacks may extend and retract slightly.
Do not interrupt this cycle. Let it run until the panel returns to its idle state, which usually takes 30 seconds to 2 minutes. Once calibration is complete, test the jacks by pressing the level button again. They should respond smoothly. If they do not, move to the troubleshooting section below.
Reset steps for Lippert Command Center and iCommand systems
Older Lippert Command Center panels have a slightly different reset. Locate the small reset button on the back or side of the panel—it is usually recessed and requires a pen or small tool to press. With the panel powered on, press and hold this reset button for 5 to 10 seconds until you see the display flash or hear a beep.
Release the button and allow the panel to restart. The system will run a brief calibration, and the jacks may move slightly. Once the panel returns to normal display, test the jacks as you would with the Ground Control system.
The Lippert iCommand app-based system works differently because it communicates wirelessly. If your RV uses iCommand, open the app on your phone and look for a "Reset" or "Recalibrate" option in the settings menu. Tap it and follow the on-screen prompts. The app will guide you through the process and confirm when calibration is complete.
What to check before you reset
Before you attempt a reset, verify that the system actually has power. Check the main RV battery—if it is dead or disconnected, the leveling system will not respond no matter what you do. Connect the battery or charge it fully, then try the reset.
Next, locate the fuse or breaker that protects the leveling system. This is usually labeled "Level," "Auto Level," or "Jacks" on your RV's electrical panel. If the fuse is blown, replacing it may be all you need—no reset required. A blown fuse usually means the system tried to draw too much power, often because a jack is stuck or the pump is failing. If you replace the fuse and it blows again when ready, stop and have the hydraulic system inspected by a technician.
Also check that the hydraulic fluid reservoir is full. On most RVs, this is a translucent tank mounted near the jacks or under the vehicle. If the fluid level is low, the pump cannot build pressure and the jacks will not move. Top it off with the correct Lippert hydraulic fluid before you reset.
When a reset does not work
If you have completed the reset and the jacks still will not move or move only partially, the problem is not a memory loss—it is a mechanical or electrical failure. The most common causes are a dead or low battery, a blown fuse that keeps blowing, a failed hydraulic pump, or a stuck jack.
Test the battery voltage with a multimeter if you have one. The RV battery should read at least 12 volts when the engine is off. If it reads below 11 volts, charge it fully and try the reset again. If the battery is good but the fuse blows again when you power on the system, the pump or a jack is drawing too much current and needs professional repair.
If the battery is good, the fuse stays intact, and the jacks still do not respond, the hydraulic system itself may have failed. This requires a technician to diagnose—they will check pump pressure, jack seals, and hose integrity. Do not force the jacks or try to operate them manually, as this can cause further damage.
Preventing future resets and system failures
Most Lippert Auto Level problems can be prevented with basic maintenance. Check the hydraulic fluid level every few months and top it off if needed. Dirty or low fluid causes the pump to work harder and fail sooner. Use only Lippert-approved hydraulic fluid—mixing brands or using the wrong type can damage seals and cause leaks.
Keep the battery charged, especially during the off-season. A battery that sits dead for months can lose its ability to hold a charge. If you store your RV for more than a few weeks, use a battery maintainer to keep it at full voltage.
Test the leveling system every few weeks by pressing the level button and listening for the pump to set up. If you hear nothing or the jacks move very slowly, the system is struggling and may need service soon. Catching problems early is much cheaper than waiting for a complete failure.
Frequently Asked Questions
Do I need to level my RV every time I park?
Yes. An unlevel RV can damage the refrigerator, cause propane to flow incorrectly, and make water drain the wrong way. Even a slight tilt matters. Always run the Auto Level before you set up camp, even if the ground looks flat.
Can I manually lower the jacks if the Auto Level fails?
Some Lippert systems have a manual override valve, usually located on the pump or near the jacks. Consult your manual to find it. Manual lowering is slow and requires physical effort, but it can get you mobile in an emergency. Do not use manual override as a regular solution—it means the automatic system needs repair.
How long does a Lippert Auto Level system usually last?
With proper maintenance, a Lippert system typically lasts 10 to 15 years. Hydraulic pumps and seals degrade over time, especially if the fluid is not changed or the system sits unused for long periods. Regular use and fluid checks extend the lifespan significantly.
Will resetting the system erase any stored settings or presets?
A reset clears the calibration memory but does not erase user settings like favorite level positions or app preferences on iCommand systems. After a reset, you may need to recalibrate the jacks, but your other settings remain intact.
What if the reset button is stuck or broken?
If the physical reset button will not press, try the power-cycle method instead: turn off the main power switch for 10 seconds, then turn it back on. This achieves the same result. If neither method works, the control panel itself may be failing and will need replacement by a technician.