The Lisle 28100 is a manual tool that disconnects ball joints without damaging the surrounding suspension parts
The Lisle 28100 ball joint separator is a hand-operated tool designed to press a ball joint stud out of its socket in the steering knuckle or control arm. Unlike a pickle fork (which hammers the joint apart and often damages the rubber boot), the Lisle 28100 uses steady mechanical pressure to separate the joint cleanly. It costs between $40 and $80 new, depending on the retailer, and works on most domestic and import vehicles with standard ball joint sizes.
You need this tool when you're replacing a worn ball joint, tie rod end, or sway bar link, or when you're removing a control arm for other suspension work. The tool saves you money by letting you do the separation yourself instead of paying a shop labor rate, and it reduces the risk of damaging the rubber dust boot that keeps dirt out of the joint. If you're doing suspension work at home and don't already own a ball joint separator, the Lisle 28100 is the most common choice among DIY mechanics.
Key Takeaways
- The Lisle 28100 uses a screw mechanism to press a ball joint stud out of its socket without hammering, which protects the rubber boot from damage.
- You need this tool when replacing ball joints, tie rod ends, sway bar links, or control arms that are bolted to the steering knuckle.
- The tool works on most vehicles with standard ball joint sizes, but you should check your vehicle's service manual or a parts diagram to confirm the joint size before buying.
- A pickle fork is cheaper but hammers the joint apart and often tears the rubber boot, making it a false economy if you're keeping the vehicle long-term.
- The Lisle 28100 is a one-time purchase that will last for years if stored dry, so the cost spreads across multiple repairs.
How the Lisle 28100 works compared to other separation methods
The Lisle 28100 has two main parts: a C-shaped frame that straddles the ball joint, and a threaded screw with a small cone-shaped tip. You position the frame so the cone tip contacts the ball joint stud (the shaft that goes into the socket), then turn the screw handle. As you turn, the screw pushes the stud out of the socket with steady, controlled pressure. The process takes a minute or two per joint and requires no hammering.
A pickle fork, by contrast, is a wedge-shaped tool that you position under the ball joint and then strike with a hammer. The impact forces the stud out of the socket, but the shock often tears the rubber dust boot and can damage the socket itself. Pickle forks cost $10 to $20, which is why some shops still use them on vehicles they don't expect to see again. If you're keeping your vehicle, the Lisle 28100's gentler approach is worth the extra cost.
A ball joint press (a large shop tool that costs $200 to $500) does the same job as the Lisle 28100 but with more force and precision. Most home mechanics don't own one because the Lisle 28100 handles the vast majority of separations without needing extra power.
What size ball joint your vehicle has and how to check before buying
Ball joint studs come in different diameters. The most common sizes are 9/16 inch, 5/8 inch, and 3/4 inch. The Lisle 28100 is designed for studs in the 9/16-inch to 3/4-inch range, which covers most passenger cars, light trucks, and SUVs built in the last 30 years. However, some older vehicles, some heavy trucks, and some European cars use different sizes.
To find your vehicle's ball joint size, check your owner's manual or service manual (often available free online through manufacturer websites or repair databases). You can also look at a parts diagram on a retailer's website — enter your vehicle's year, make, and model, and the diagram will show the ball joint assembly. If you're unsure, call a local parts store with your vehicle information and ask them to confirm the size. Buying the wrong size tool means a wasted trip and a return.
When to use the Lisle 28100 versus when to take it to a shop
Use the Lisle 28100 if you're already doing suspension work yourself, have a basic set of hand tools, and have a safe place to work (a level surface, jack stands, and good lighting). The tool itself is straightforward — there's no learning curve beyond positioning it correctly and turning the screw steadily. If you've replaced brake pads or changed oil before, you have the skill level to use this tool.
Take the work to a shop if you don't have a safe way to lift the vehicle, if you're not comfortable working under a car on jack stands, or if the ball joint is seized so badly that the Lisle 28100 won't budge it (this is rare, but it happens on very old vehicles or ones exposed to salt). A shop will charge $100 to $300 per ball joint for labor, depending on location and the vehicle. If you're only replacing one joint, that might be worth it. If you're replacing multiple joints or doing other suspension work, the Lisle 28100 pays for itself on the first job.
How to use the Lisle 28100 step by step
First, remove the wheel and tire, then unbolt the ball joint from the control arm or steering knuckle (consult your service manual for the exact bolt locations and torque specs). You don't need to remove the entire control arm — just disconnect the ball joint stud from the socket. Position the Lisle 28100 so the C-frame straddles the joint and the cone tip of the screw contacts the center of the ball joint stud. The frame should rest against the steering knuckle or control arm on either side of the joint.
Turn the screw handle clockwise slowly and steadily. You'll feel resistance as the screw pushes the stud. Keep turning — don't jerk or hammer. After 30 seconds to two minutes, the stud will pop out of the socket with a sudden release of pressure. Stop turning when ready. Remove the tool, and the joint is separated. The rubber boot should still be intact.
If the stud won't budge after a full minute of steady turning, stop and check your setup: make sure the cone tip is centered on the stud, the frame is seated firmly against the knuckle or arm, and you're turning the screw (not trying to pull or pry). If everything looks right and it still won't move, the joint may be seized. At that point, a shop with a hydraulic press is your better option.
Storage and maintenance of the Lisle 28100
The Lisle 28100 requires almost no maintenance. After each use, wipe off any dirt or grease with a dry cloth. Store it in a dry place — a toolbox, garage shelf, or pegboard. The screw mechanism will last for years if you don't expose it to moisture or drop it repeatedly. If the screw becomes stiff or hard to turn, a light spray of penetrating oil (like WD-40) on the threads will restore smooth operation.
Because the tool is durable and you'll use it only when you need it, the cost per use drops significantly over time. A mechanic who does suspension work regularly will use the same Lisle 28100 for 10 or 15 years.
Frequently Asked Questions
Will the Lisle 28100 work on my truck or SUV?
It will work on most trucks and SUVs with standard ball joint sizes (9/16 inch to 3/4 inch). Heavy-duty trucks and some older models may use larger studs. Check your service manual or call a parts store with your vehicle's year, make, and model to confirm the size before buying.
Can I use the Lisle 28100 on tie rod ends and sway bar links?
Yes. Tie rod ends and sway bar links use the same ball-and-socket design as ball joints, and the Lisle 28100 separates them the same way. Make sure the stud size matches — most tie rod ends are 9/16 inch or 5/8 inch, which the tool handles.
What if I damage the rubber boot while separating the joint?
If the boot tears, the joint will collect dirt and moisture and fail faster. If you're replacing the ball joint anyway, a torn boot doesn't matter — you're throwing the old joint away. If you're separating the joint to remove a control arm or other part and keeping the joint, a torn boot means you should plan to replace the joint soon or rebuild it with a new boot kit.
Is the Lisle 28100 better than a pickle fork?
Yes, if you're keeping the vehicle. The Lisle 28100 protects the rubber boot and is gentler on the socket. A pickle fork is cheaper and faster if you don't care about damage, but the Lisle 28100's extra cost is worth it for long-term ownership.
Do I need any special safety equipment to use this tool?
You need the same safety setup as any suspension work: the vehicle on jack stands (not just a jack), wheel chocks to prevent rolling, and good lighting. Wear safety glasses in case debris flies, and keep your hands clear of the screw mechanism while turning it. Never work under a vehicle supported only by a jack.