What .22-250 load data tells you and where to find it

Load data is a table of tested powder charges, bullet weights, and primer types that produce safe, accurate rounds in a specific caliber. For .22-250, load data shows you the minimum and maximum powder charge for each combination of powder type, bullet weight, and primer — and the velocity you should expect. You need this data before you reload because the difference between a safe load and a dangerous one can be a few grains of powder.

Load data for .22-250 comes from powder manufacturers (Hodgdon, IMR, Alliant, Vihtavuori), bullet makers (Sierra, Hornady, Nosler), and reloading manual publishers (Lyman, Lee, RCBS). Each source tests their own combinations and publishes results. A single bullet weight — say, 55 grains — will have different load data depending on which powder you use, which primer you choose, and which source published the data. You cross-reference your specific setup against the table to find your safe range.

Key Takeaways

  • Load data tables show minimum and maximum powder charges for each powder type and bullet weight combination, and you must stay within the published range for that exact setup.
  • Powder manufacturers and reloading manual publishers test different combinations, so the same bullet weight will have different load data depending on your powder choice.
  • Starting loads are typically 10 percent below maximum; you work up in small increments and watch for pressure signs like flattened primers or hard extraction.
  • The .22-250 is a high-velocity cartridge that is sensitive to powder charge weight, so measuring by volume instead of weight can produce dangerous pressures.
  • Load data varies by rifle, barrel length, and primer type, so data from one source may not match another even for the same bullet and powder.

Why .22-250 load data is tighter than larger cartridges

The .22-250 is a small, high-velocity cartridge with a case capacity of roughly 26 to 27 grains of water. That small case means powder charges are measured in single-digit grain weights — typically 3 to 5 grains depending on the powder type. A one-grain error in a large magnum cartridge might raise pressure by 1,000 PSI; in the .22-250, the same error can raise pressure by 3,000 to 5,000 PSI because the powder is compressed into a much smaller space.

This sensitivity is why reloaders use a scale to measure powder by weight, not a powder measure set by volume. A volumetric measure works reasonably well for large cartridges because small variations in powder density average out over larger charges. In the .22-250, they do not. You also cannot safely use load data from one powder in place of another — Hodgdon H322 and IMR 4895 both work in the .22-250, but their burn rates are different enough that the safe charge for one is not safe for the other.

How to read a .22-250 load table

A typical load table lists the bullet weight, powder type, primer type, case brand, and then minimum charge, maximum charge, and velocity at maximum. Here is a simplified example of what you will see:

BulletPowderPrimerMin ChargeMax ChargeVelocity (Max)
55 grH322CCI 45024.0 gr26.0 gr3,680 fps
55 grIMR 4895CCI 45022.5 gr24.5 gr3,650 fps
60 grH322CCI 45023.5 gr25.5 gr3,520 fps

You start at the minimum charge listed for your exact combination of bullet weight, powder, and primer. You load five rounds at that charge, fire them, and inspect the brass and primers for pressure signs. If the primers are slightly flattened or the cases are hard to extract, you are at or near maximum pressure. If the brass looks normal, you increase the charge by 0.3 to 0.5 grains, load five more rounds, and repeat. You stop when you see pressure signs or when you reach the published maximum — whichever comes first.

Pressure signs and when to stop working up

Pressure signs in the .22-250 appear in this order: flattened or cratered primers (the primer cup dents inward), hard extraction (the bolt is difficult to open), and then case bulging or splits. You will not see a visible case bulge in the .22-250 until pressure is already dangerous, so you rely on primer and extraction feel as your warning signs.

If you see flattened primers, stop when ready and drop back 0.5 grains from that charge. That is your working maximum for that rifle, powder, bullet, and primer combination. Do not assume that because a reloading manual lists 26.0 grains as safe, you can load 26.0 grains in your rifle — your barrel, chamber, and firing pin may produce higher pressures than the test rifle used to develop the data. The published maximum is a ceiling, not a target.

Common .22-250 powders and their load data ranges

The most common powders for .22-250 are H322, IMR 4895, and Varget. H322 is a medium-burn-rate powder that produces velocities around 3,600 to 3,700 fps with 55-grain bullets and charges in the 24 to 26 grain range. IMR 4895 is slightly slower and typically runs 22.5 to 24.5 grains for the same bullet. Varget is faster-burning and works well with heavier bullets (60 to 70 grains) with charges around 23 to 25 grains.

Each powder has a different pressure curve, so load data for one is not interchangeable with another. If your manual lists H322 data and you want to use IMR 4895 instead, you must find load data specifically for IMR 4895 — either from a different manual, from the IMR website, or from Hodgdon's online database. Guessing or interpolating between powders is how dangerous pressures happen.

Where to find published .22-250 load data

Hodgdon publishes free load data on their website organized by caliber and bullet weight. IMR, Alliant, and Vihtavuori do the same. Reloading manuals from Lyman, Lee, and RCBS contain .22-250 data in print form, which is useful if you reload without internet access. Sierra and Hornady publish load data in their reloading manuals and on their websites.

If you are using a specific brand of bullet, start with that bullet maker's website — they often have load data for their own bullets. If you are using a specific powder, check the powder maker's site. Cross-referencing multiple sources is normal; you may find that Hodgdon lists 26.0 grains as maximum for a 55-grain bullet while Lyman lists 25.5 grains for the same bullet and powder. Both are correct for their test rifles. You use the more conservative (lower) number unless you have a specific reason to trust the higher one.

Why load data varies between sources and rifles

Load data is published from test rifles, and test rifles are not your rifle. Variations in chamber dimensions, barrel length, firing pin protrusion, and even primer seating depth can shift pressure by 1,000 to 3,000 PSI. A .22-250 with a 24-inch barrel will produce higher velocities than one with a 20-inch barrel using the same load. A rifle with a tight chamber will produce higher pressures than one with a loose chamber.

This is why you always start at the minimum charge and work up in your own rifle, even if you have loaded the same cartridge before. Your new barrel, new brass, or new primer lot may behave differently. The published data is a starting point, not a may provide.

Frequently Asked Questions

Can I use load data from one reloading manual in a different manual?

Yes, but only if both manuals list the same powder, bullet weight, and primer type. Do not assume that because Lyman lists a load that Hornady will agree with it — they test in different rifles. If the two sources disagree, use the lower charge and work up from there in your own rifle.

What if I cannot find load data for my exact bullet weight?

Interpolate conservatively downward. If you have data for 55-grain and 60-grain bullets but you are loading 58-grain bullets, start at the 60-grain minimum and work up. Never interpolate upward or assume a charge between two weights is safe without testing it.

Is it safe to use a powder measure instead of a scale for the .22-250?

No. Powder measures are volumetric and work by space, not weight. Powder density varies by lot and temperature, so a measure set for one lot of H322 may throw charges that are 0.5 grains off with a different lot. In the .22-250, that error matters. Use a scale.

What happens if I load above the maximum charge listed?

Pressure rises into the dangerous range, which can flatten primers, make extraction difficult, or cause case splits. In extreme cases, it can damage the rifle or cause injury. The maximum is not a suggestion — it is the limit of safe pressure for that test rifle.

Do I need different load data if I use a different primer?

Yes. Different primers have different hardness and cup thickness, which affects how the cartridge pressurizes. CCI 450 and Federal 205 primers will produce slightly different pressures with the same powder charge. Always use load data that matches your primer type.