What a mechanical pump does in Create Mod

A mechanical pump in Create Mod is a block that moves fluids from one tank or pipe network to another using rotational power. Unlike passive fluid transfer, the pump requires energy — typically from a water wheel, windmill, or other rotating component — to push liquid uphill, across distance, or against pressure. Without a pump, fluids in Create Mod flow only downward by gravity.

The pump is one of the core tools for building automated factories and farms in Create Mod because most production chains need water, lava, or other liquids moved to specific locations. A pump lets you centralize your fluid sources and distribute them where they're needed, rather than building separate tanks at each workstation.

Key Takeaways

  • A mechanical pump converts rotational power into fluid movement and can push liquids uphill or across horizontal distances that gravity alone cannot handle.
  • The pump must be connected to a rotating shaft or gear system to function; without rotational input, it will not move fluid.
  • Fluid pipes connect to the pump's input and output sides, and the direction of rotation determines which side acts as inlet and which as outlet.
  • Pump speed affects flow rate — faster rotation moves more fluid per second, but excessive speed can cause backup or overflow in small pipe networks.

How to connect a pump to a power source

A mechanical pump needs rotational power to operate. You can connect it to any spinning shaft in your Create Mod setup — a water wheel, windmill, hand crank, motor, or even a gear train powered by another source. The pump attaches to the side of the shaft, and the direction of rotation determines which pipe connection acts as the inlet (where fluid enters) and which acts as the outlet (where fluid exits).

The simplest setup for beginners is a water wheel powering a pump. Place the water wheel next to a flowing water source, attach the pump to the shaft extending from the water wheel, then connect fluid pipes to the pump's inlet and outlet. The water wheel's rotation will when ready begin pushing fluid through the outlet pipe. If you need the pump to push fluid in the opposite direction, rotate the pump 180 degrees or reverse the direction of the shaft powering it.

Inlet and outlet sides of the pump

The mechanical pump has two fluid connection points: one side receives fluid (inlet) and the opposite side pushes it out (outlet). The direction of the shaft's rotation determines which is which. If you connect a pipe to the wrong side, the pump will not move fluid in the direction you want, and you may see fluid back up in your pipes.

To identify which side is which, watch the pump's animation when it is spinning. The pump has a visible piston or rotor that moves in the direction of flow. The side where the piston moves inward is the inlet; the side where it moves outward is the outlet. If your setup is not working, try rotating the pump 180 degrees or reversing the shaft rotation to swap inlet and outlet.

Pump speed and flow rate

The speed at which the pump's shaft rotates directly affects how much fluid it moves per second. A faster-spinning pump moves more fluid, while a slower pump moves less. In Create Mod, rotational speed is measured in revolutions per minute (RPM). A pump running at 16 RPM will move fluid more slowly than one running at 256 RPM.

However, faster is not always better. If your pump is moving fluid faster than your pipes or destination tanks can handle, fluid will back up and may overflow or cause pressure issues. For most small-scale setups, a pump running at 16 to 64 RPM is sufficient. You can control pump speed by using gearboxes or gear ratios to step down the rotation from your power source before it reaches the pump.

Common pump setups for different tasks

A straightforward lift pump is the most basic use: place a pump at the bottom of a vertical pipe run with a tank above it. The pump pushes water upward against gravity, filling the tank. This is essential for any setup where you need fluid at a height, such as filling a cauldron for a water wheel or supplying a second-floor production line.

A distribution pump sits at a central tank and pushes fluid through multiple branch pipes to different machines or tanks. This lets you supply water, lava, or other fluids to several workstations from a single source. Use pipe junctions and valves to control which branches receive fluid and at what rate.

A circulation pump moves fluid in a loop through a system — for example, pumping water through a cooling system or recycling fluid back to a central tank after it has been used. This is common in large factories where you want to reuse water or lava rather than letting it drain away.

Troubleshooting a pump that is not moving fluid

If your pump is spinning but no fluid is moving, check these points in order. First, confirm the pump is actually receiving rotational power — look for the spinning animation on the shaft. If the shaft is not moving, your power source is not connected or is not generating enough torque. Second, verify that fluid is actually present on the inlet side. A pump cannot move fluid that is not there; if your inlet pipe is empty, fill the source tank first.

Third, check that your outlet pipe is not blocked or overfilled. If the destination tank is completely full or the outlet pipe is clogged, the pump may not be able to push fluid through. Open a valve or drain some fluid to relieve pressure. Fourth, confirm that the inlet and outlet are connected to the correct sides of the pump. If you connected both pipes to the same side, or if the inlet and outlet are reversed, the pump will not function as expected. Rotate the pump or reverse the shaft direction to fix this.

Frequently Asked Questions

Can I use a mechanical pump to move lava?

Yes. A mechanical pump moves any fluid in Create Mod, including lava, honey, and custom modded fluids. Lava requires the same rotational power as water, so your power source does not need to be stronger. Use fluid pipes rated for hot fluids if you want to avoid visual glitches, though mechanically any pipe works.

What happens if I connect the pump backwards?

If you connect the inlet and outlet pipes to the wrong sides of the pump, fluid will not move in the direction you want. The pump will either push fluid back toward the source or not move it at all. Rotate the pump 180 degrees or reverse the direction of the shaft to swap the inlet and outlet sides.

How much rotational power does a pump need?

A mechanical pump requires only 1 RPM of rotational input to function. However, at 1 RPM it moves fluid very slowly. Most practical setups use 16 to 256 RPM depending on how quickly you need fluid moved. A water wheel or windmill provides enough power for a pump without additional boosters.

Can I pump fluid upward indefinitely?

Yes, a pump can push fluid to any height as long as it has rotational power. There is no height limit in Create Mod. However, the higher you pump fluid, the longer it takes to fill the destination tank. For very tall builds, use multiple pumps in series or increase the pump speed to move fluid faster.

Do I need a valve between the pump and the pipe?

No, a valve is not required. However, adding a valve on the outlet side lets you control or stop fluid flow without shutting down the pump. This is useful if you want to pause production or redirect fluid to a different tank without stopping your entire power system.