Motion Raceworks steering wheels are aftermarket replacements designed for racing and performance driving, not factory equipment

Motion Raceworks is a manufacturer of custom steering wheels sold primarily through online retailers and specialty automotive shops. These wheels are not original equipment—they do not come on any car from the factory. You buy them separately and install them to replace your car's stock steering wheel, usually because you want a smaller diameter, a different grip material, a quicker turn ratio, or the look of a racing setup.

The key thing to understand is that swapping your steering wheel changes how your car handles and how its safety systems work. Your airbag, horn pad, and steering angle sensor all live in or connect to the wheel. Removing the original wheel and bolting on an aftermarket one means those systems either stop working, work differently, or require additional parts to function at all. This is not a cosmetic change—it affects steering feel, safety, and sometimes legality depending on where you drive.

Key Takeaways

  • Motion Raceworks wheels require you to remove your car's airbag, which means you lose frontal impact protection unless you install an aftermarket airbag module.
  • The steering wheel connects to your car's angle sensor and electronic stability control; removing it can trigger warning lights and disable safety features.
  • Installation requires disconnecting the battery, removing the horn pad and airbag, unbolting the original wheel, and reconnecting the horn and electrical connectors to the new wheel.
  • Aftermarket wheels may not be street-legal in all states, and some insurance companies will not cover accidents if a non-OEM wheel contributed to the damage.
  • Cost ranges from roughly $150 to $600 for the wheel itself, plus $200 to $500 in labor if a shop does the work, or the cost of an aftermarket airbag if you want one installed.

Why people install Motion Raceworks wheels and what changes

Drivers choose aftermarket wheels for three main reasons: feel, appearance, and function. A smaller-diameter wheel (typically 320 mm instead of the stock 370 mm) requires less hand movement to turn the car, which is useful in racing or autocross. A thicker grip or wrapped leather feels different in your hands during long drives. And a wheel without a large airbag housing looks more like a race car, which appeals to people who track their vehicles or want that aesthetic.

What changes when you install one: your steering ratio stays the same (the mechanical relationship between wheel turn and tire turn), but the mechanical advantage changes. A smaller wheel means you turn it more to achieve the same tire movement, or you turn it less to move the tires the same amount—depending on how you think about it. In practice, a smaller wheel feels quicker and more responsive. Your hands also sit closer to the horn pad and spokes, so the ergonomics shift. And your car loses its airbag unless you pay extra to keep one.

What you need to know about airbags and safety systems

Your factory steering wheel contains an airbag module that deploys in a frontal crash. When you remove it, that protection is gone. Some Motion Raceworks wheels come with a small airbag pocket built in, but most do not. If you want to keep airbag protection, you must buy an aftermarket airbag module separately—these cost $300 to $800 and require professional installation because they need to be wired into your car's airbag control unit.

Your steering wheel also connects to the steering angle sensor, which tells your car's electronic stability control and traction control how far you have turned the wheel. If this sensor is not reconnected properly to the new wheel, your stability control warning light will stay on and those systems will not work. Some aftermarket wheels have a sensor connector built in; others require you to transfer the sensor from the old wheel. If the sensor is damaged during removal, you will need a replacement, which costs $100 to $300 plus labor.

The horn pad—the center button that sounds the horn—also lives in the steering wheel. Most aftermarket wheels include a horn pad, but you have to transfer the electrical connector from the old wheel to the new one. If you do not do this correctly, your horn will not work.

How to install a Motion Raceworks steering wheel

Installation is a job you can do yourself if you are comfortable working with electrical connectors and have basic hand tools, or you can pay a shop to do it. The process takes 30 minutes to an hour if nothing goes wrong.

  1. Disconnect the battery negative terminal. This prevents accidental airbag deployment while you work.
  2. Remove the airbag. On most cars, this means prying or unbolting a cover on the back of the steering wheel, then unbolting the airbag module itself. Disconnect the airbag electrical connector—do not pull on the wires.
  3. Remove the horn pad connector. This is usually a small clip or plug behind the wheel. Disconnect it gently.
  4. Unbolt the steering wheel. Most wheels are held by a single large bolt in the center. Mark the wheel and steering column with tape or a marker so you can reinstall it in the same position—this keeps your steering angle sensor calibrated.
  5. Lift the old wheel off and set it aside. The steering shaft will be exposed.
  6. Slide the new wheel onto the shaft and align your marks. Bolt it down to the torque specification in your new wheel's instructions, usually 25 to 35 foot-pounds.
  7. Connect the horn pad connector to the new wheel. Make sure the connector clicks into place.
  8. Reconnect the airbag (if you are keeping one) or leave it disconnected. If you leave it disconnected, the airbag warning light will stay on permanently.
  9. Reconnect the battery. Start the car and check that the horn works and that warning lights are normal.

If your car has a steering angle sensor that needs to be transferred, the shop manual for your specific model will show where it is and how to move it. If you are unsure, have a shop do this step—a misaligned sensor can cause stability control to malfunction.

Cost breakdown for a Motion Raceworks wheel installation

The wheel itself typically costs $150 to $600 depending on the model, material (leather, suede, alcantara, or wrapped), and diameter. Shipping adds $20 to $50.

If you install it yourself, your only additional cost is a replacement airbag warning light bulb if you are leaving the airbag disconnected (roughly $5 to $15). If you want to keep airbag protection, add $300 to $800 for an aftermarket airbag module and $200 to $400 for a shop to install it.

If a shop installs the wheel for you, labor typically runs $200 to $500 depending on your car and whether the steering angle sensor needs work. Some shops charge a flat rate; others charge hourly. Call ahead and ask whether the quote includes sensor transfer and horn pad reconnection.

Street legality and insurance considerations

Aftermarket steering wheels are legal to own and install in most U.S. states, but some states have rules about steering wheel diameter and spoke design. A few states require a minimum diameter (usually 13 inches or 330 mm) and prohibit certain spoke patterns. Check your state's vehicle code or call your local DMV to confirm—the rules vary.

Insurance is a separate issue. If you are in an accident and your insurance company determines that the aftermarket wheel contributed to the damage or that you removed safety equipment (the airbag), they may deny your claim or reduce your payout. Some insurers require you to notify them of modifications; others do not care. Read your policy or call your agent before you install the wheel. If you track your car at a race track, your street insurance almost certainly does not cover you—you will need track-day insurance, which is separate.

Frequently Asked Questions

Will a Motion Raceworks wheel fit my car?

Motion Raceworks wheels come in different bolt patterns and hub sizes to fit different cars. You must match the bolt pattern (the number and spacing of holes) and the hub diameter to your car's steering column. Check the product listing or contact Motion Raceworks with your car's year, make, and model before you buy. Installing a wheel with the wrong bolt pattern will not work and can damage your steering column.

Do I have to remove the airbag?

Yes. The airbag module is built into the factory steering wheel and cannot stay in place if you remove the wheel. You can either leave the airbag disconnected (and live with a warning light), buy an aftermarket airbag module, or accept that you have no frontal airbag protection. There is no way to keep your original airbag working with an aftermarket wheel.

Will my steering angle sensor work with an aftermarket wheel?

It depends on the wheel and your car. Some aftermarket wheels have a sensor connector built in; others require you to transfer the sensor from the old wheel. If the sensor is not connected or is misaligned, your stability control will not work and you will see a warning light. Have a shop verify the sensor connection after installation if you are not sure.

Can I return to my factory wheel later?

Yes. As long as you keep your original wheel and airbag, you can reinstall them whenever you want. The process is the reverse of installation. If you damaged the airbag during removal, you will need to buy a replacement, which costs $300 to $600 depending on your car.

Will an aftermarket wheel make my car harder to steer?

No. The steering ratio—how much the wheels turn for each turn of the steering wheel—does not change. What changes is the mechanical advantage. A smaller wheel requires more hand movement to achieve the same tire movement, so it may feel like more effort, but most people find a smaller wheel easier to turn because it requires less force. The difference is usually small and takes a few drives to get used to.