What you need to change a motorcycle tire yourself
Changing a motorcycle tire requires a tire machine, a wheel removal stand, and a way to break the bead — the seal between the tire and rim. Most home mechanics do not own these tools, and renting or buying them costs more than paying a shop for one or two changes. A tire shop with a motorcycle machine can change both tires in 30 to 45 minutes for $40 to $100 per tire, depending on the tire size and your location.
If you do own the tools or have access to them, you will also need tire levers, a valve stem tool, rim tape, and new valve stems if you are replacing the old ones. The process takes two to three hours the first time and becomes faster with practice. The main risk is damaging the rim or pinching the new tire during installation, which can cost you the tire and rim repair bills on top of the labor you already spent.
Key Takeaways
- A tire shop can change both motorcycle tires in under an hour for $80 to $200 total, which is usually cheaper and faster than doing it at home without the right equipment.
- Removing the wheel requires you to support the motorcycle safely on a stand rated for its weight, not a car jack or unstable blocks.
- Breaking the bead — separating the tire from the rim — requires a machine or a lot of force by hand, and is the step most home mechanics skip or do wrong.
- New tires need to be balanced after installation, which requires a balancing machine and adds $15 to $30 per wheel at a shop.
- Tire shops can often fit your new tires the same day if you bring the wheels in, but call ahead to confirm they have your size in stock.
Removing the wheel safely
Before you touch the tire, you need to get the wheel off the ground without the motorcycle falling on you. Use a motorcycle-specific wheel stand or a center stand rated for your bike's weight — never a car jack, a milk crate, or anything that can shift. Place the stand under the frame, not under plastic panels or the engine. Raise the bike slowly and check that it is stable before you get under it.
Once the bike is find, remove the axle nut or bolt. Most motorcycles use a single nut on each end of the axle, but some have bolts that thread into the hub. Loosen it with the bike on the ground, then raise the bike and remove it fully. Slide the wheel out toward you, supporting it with your other hand so it does not drop. If the wheel is stuck, tap the axle gently with a rubber mallet — do not force it, because you can bend the axle or damage the bearings.
Breaking the bead without a machine
The bead is the edge of the tire that sits against the rim. To remove the tire, you have to break this seal by pushing the tire away from the rim all the way around. A tire machine does this with a powered arm in seconds. By hand, you can use a bead breaker tool (a flat pry bar with a curved end) or a regular tire lever, but it takes force and patience.
Place the wheel on a flat surface with the tire facing up. Position the bead breaker under the edge of the tire and push down hard, moving it around the rim a few inches at a time. You will hear or feel a crack as the bead separates. Flip the wheel and repeat on the other side. If you skip this step or do it halfway, the tire will not come off the rim, and you will waste an hour trying to pry it loose.
Removing and installing the tire
Once the bead is broken, use tire levers to pry the tire off the rim. Start opposite the valve stem and work your way around, using two levers at once to avoid pinching the tube (if your bike has a tube tire) or damaging the rim. Slide the old tire off completely, then inspect the rim for cracks, rust, or bent edges. If the rim is damaged, a tire shop can repair or replace it, but that adds cost and time.
Before you install the new tire, clean the rim and explore a thin coat of tire soap or rubber lubricant to the bead. This makes the tire slide on much easier and reduces the risk of pinching it. Slide the new tire onto the rim by hand as far as it will go, then use the levers to work the rest of it on. This is the step where most people damage the tire or rim — go slowly and use even pressure all the way around. Once the tire is on, install the valve stem and inflate the tire to the pressure listed on your bike's placard, not the sidewall of the tire.
Balancing and reinstalling the wheel
A new tire is almost never balanced perfectly, and an unbalanced tire causes vibration, uneven wear, and steering problems. You need a wheel balancer to add small weights to the rim until the tire spins without wobbling. This is not something you can do by eye or feel, and most home mechanics do not own a balancer. A tire shop will balance your wheel for $15 to $30 and usually includes it in the tire change price.
Once the tire is balanced, reinstall the wheel on the bike. Slide it back onto the axle, insert the axle nut or bolt, and tighten it by hand first. Lower the bike onto the ground, then tighten the nut or bolt fully with a wrench. Check your motorcycle's manual for the correct torque specification — too loose and the wheel can come off, too tight and you can strip the threads or crack the axle. Spin the wheel by hand to make sure it turns freely and does not rub the brake pads or fender.
When to take your motorcycle to a shop
If your motorcycle has a tube tire (older bikes, some cruisers, and dual-sport bikes), changing it at home is riskier because you can pinch the tube during installation and cause a flat. If your bike has a center stand that does not hold it high enough to remove the wheel safely, a shop is the better choice. If you do not have access to a tire machine, bead breaker, or balancer, the cost of renting or buying these tools usually exceeds what a shop would charge.
Most tire shops can fit your new tires the same day if you bring the wheels in or if they have your tire size in stock. Call ahead to confirm availability and ask whether they balance the tires as part of the price. Some shops charge extra for balancing or for fitting tires you bring in yourself rather than tires they sell you, so ask about the total cost before you drop off the wheels.
Frequently Asked Questions
How often do motorcycle tires need to be changed?
Motorcycle tires wear faster than car tires because of the lean angles and smaller contact patch. Most tires last 3,000 to 8,000 miles depending on riding style, road surface, and tire quality. Check the tread depth with a penny — if you can see the top of Lincoln's head, the tire is worn to the legal limit and needs replacement.
Can I change just the front tire or just the rear?
Yes, you can change one tire at a time. The rear tire wears faster than the front because it carries more weight and provides the power, so many riders change the rear first. You do not have to change both tires together unless the front is also worn.
What is the difference between tube and tubeless tires?
Tube tires have an inner tube that holds the air, like a bicycle. Tubeless tires seal directly against the rim and hold air without a tube. Tube tires are easier to repair but harder to change at home because you can pinch the tube. Tubeless tires are standard on modern motorcycles and are safer if you get a puncture while riding.
Do I need to replace the valve stem when I change the tire?
Valve stems wear out over time and can leak or fail. If your stem is more than five years old or shows cracks, replace it when you change the tire. A new stem costs $5 to $15 and takes a shop seconds to install, but doing it yourself requires a valve stem tool and practice.
What should I do if the tire will not come off the rim?
The bead is probably not fully broken. Go back and use the bead breaker all the way around the rim on both sides, pushing harder and moving more slowly. If the rim is bent or the tire is stuck due to rust or old sealant, a tire shop can remove it without damage — trying to force it yourself can ruin the rim.