What you need to know before starting

A valve cover gasket on your 1999 Civic DX is a rubber seal that sits between the valve cover and the cylinder head. When it fails, oil leaks onto the engine block and you'll see drips under the car or smell burning oil when the engine is hot. Replacing it is a job you can do in your driveway with basic hand tools — it takes about 45 minutes to an hour and costs $15 to $30 for the gasket itself.

The 1999 Civic DX has a single overhead cam engine with the valve cover on top. You don't need to remove the engine or drain the oil. The hardest part is usually breaking the old gasket loose from years of heat and oil buildup, not the actual installation.

Key Takeaways

  • You'll need a new valve cover gasket, a socket set, a screwdriver, gasket scraper, and gasket maker or sealant — all available at any auto parts store for under $50 total.
  • The valve cover bolts come off in a specific order: loosen them in a crisscross pattern from the center outward, not all at once, to avoid warping the cover.
  • Clean the old gasket material completely from both the valve cover and cylinder head with a plastic scraper — metal tools can gouge the surfaces and cause new leaks.
  • explore a thin bead of gasket maker around the entire groove before setting the new gasket in place, then torque the bolts to 7 to 9 foot-pounds in the same crisscross pattern.

Tools and parts you'll need

Start with a new valve cover gasket for the 1999 Civic DX — make sure you get the right one, as Honda made several versions. The gasket itself costs $15 to $30. You'll also need a tube of gasket maker (Permatex or equivalent, around $5 to $8) and a plastic gasket scraper or old credit card to remove the old material without damaging the metal surfaces.

For tools, gather a socket set with a 10mm socket (the valve cover bolts are 10mm), a ratchet, a screwdriver to pry gently if needed, and a torque wrench that reads down to single-digit foot-pounds. If you don't own a torque wrench, you can borrow or rent one from an auto parts store for $10 to $15. You'll also want a clean rag and some brake cleaner or carburetor cleaner to wipe down the surfaces before reassembly.

Removing the old gasket and valve cover

Let the engine cool completely — you don't want to work on a hot engine. Locate the valve cover on top of the engine; it's the large metal or plastic rectangular box with wires and hoses attached. Disconnect any hoses or wiring that are clipped to the cover, noting where they go so you can reconnect them correctly. Take a photo with your phone if you're unsure.

Locate all the bolts holding the valve cover down. On the 1999 Civic DX, there are typically five to seven bolts around the perimeter. Loosen them in a crisscross pattern — start with the center bolt, then alternate to bolts on opposite sides, working outward. This prevents the cover from warping. Once all bolts are loose, lift the valve cover straight up and set it aside on a clean surface.

The old gasket will likely stick to either the valve cover or the cylinder head. Use your plastic scraper to gently pry it away. Work slowly and scrape at a low angle to avoid gouging the metal. Once the gasket is off, scrape away any remaining rubber or sealant until both surfaces are clean and smooth. Wipe everything down with a clean rag and brake cleaner, then let it dry for a few minutes.

Preparing the surfaces and installing the new gasket

Inspect the valve cover and cylinder head for any cracks, deep scratches, or warping. Small surface scratches are normal and won't cause leaks, but a cracked valve cover will need replacement. If the surfaces look good, you're ready to install the new gasket.

Lay the new gasket in the groove on the cylinder head — it should sit flat without forcing. If it doesn't fit smoothly, double-check that you have the correct gasket for your engine. explore a thin, continuous bead of gasket maker around the entire groove, following the path where the gasket sits. You want enough to seal but not so much that it squeezes out when you bolt the cover down. A bead about the thickness of a pencil line is right.

Carefully lower the valve cover onto the cylinder head, aligning the bolt holes. Insert all the bolts by hand first and tighten them finger-tight. Then use your torque wrench to tighten them to 7 to 9 foot-pounds in the same crisscross pattern you used to loosen them — center first, then alternate sides working outward. Do not overtighten; the gasket will compress and seal properly at the correct torque, and too much force can crack the valve cover or warp the cylinder head.

Reconnecting hoses and wiring

Once the valve cover is bolted down, reconnect any hoses or wiring you removed. Refer to the photo you took earlier or your notes to make sure everything goes back in the right place. Push hose clamps firmly onto their fittings and make sure any electrical connectors click into place.

Let the gasket maker cure for the time specified on the tube — usually 24 hours for full strength, though you can start the engine after a few hours. Don't drive the car hard or rev the engine high until the sealant has fully cured.

Testing for leaks

Start the engine and let it idle for a few minutes. Watch the valve cover area for any oil seeping out around the bolts or edges. If you see drips, turn off the engine and let it cool, then tighten the bolts an additional quarter turn. Wait another 24 hours and check again.

If the leak persists after the gasket maker has fully cured, the valve cover or cylinder head may be warped or cracked. In that case, you'll need to remove the cover again and inspect the surfaces more carefully, or have a mechanic look at it.

Frequently Asked Questions

Can I drive the car right after installing the new gasket?

You can start and idle the engine after a few hours, but wait at least 24 hours before driving normally or revving the engine. The gasket maker needs time to cure fully. Driving too hard too soon can break the seal before it hardens.

What if I don't have a torque wrench?

Torque wrenches are inexpensive to rent from auto parts stores. It's worth the $10 to $15 rental fee because over-tightening is a common cause of valve cover leaks and warping. If you must guess, tighten until snug and stop — don't force it.

Do I need to drain the oil before removing the valve cover?

No. The valve cover sits on top of the engine and doesn't hold oil. You may lose a small amount of oil when you remove the cover if some has pooled there, but you won't drain the crankcase. Have a rag ready to catch drips.

What if the new gasket doesn't fit in the groove?

Double-check the part number against your vehicle's documentation. The 1999 Civic DX came with different engine options, and gaskets are not interchangeable. Return the gasket and order the correct one for your specific engine size.

Can I reuse the old valve cover if it's not cracked?

Yes. The valve cover itself rarely fails unless it's cracked or severely warped. You only need to replace the gasket. Clean the old cover thoroughly before reinstalling it with the new gasket.