Training wheels on a PW50 come off when your child can balance the bike through turns and hold a straight line without touching down
The Yamaha PW50 is a 50cc automatic mini bike designed for children aged 4 to 8, and it comes with training wheels as standard. Training wheels stay on until your child demonstrates consistent balance—not just the ability to pedal in a straight line, but the ability to lean into turns without the bike tipping or the training wheels catching the ground. Most children reach this point between 20 and 40 hours of riding time, though some take longer and some are ready sooner.
Removing training wheels too early creates a real safety problem: your child will panic when the bike leans, grab the brakes hard, and either lock the rear wheel or tip over sideways. Leaving them on too long teaches your child to rely on them for balance, which actually delays learning. The goal is to remove them when your child's body has learned to shift weight automatically—when they stop thinking about balance and just ride.
Key Takeaways
- Training wheels should come off when your child can navigate gentle turns without the wheels touching ground or the bike feeling unstable.
- The PW50 training wheel bolts are located on the rear axle and require a 10mm wrench or socket to remove; keep the bolts and brackets in case you need to reinstall them.
- Before removing training wheels, practice in an open, flat area with no obstacles, and have your child wear a helmet, wrist guards, and knee pads.
- After removal, expect several falls during the first few rides as your child's body learns to correct balance automatically rather than relying on the training wheels.
- If your child is not ready after 40 to 50 hours of riding, do not force removal; continuing to ride with training wheels is safer than removing them before balance develops.
How to tell if your child is ready
Watch for three specific signs during normal riding. First, your child should be able to steer through gentle S-curves without the training wheels touching the ground or the bike feeling wobbly. Second, they should be able to stop the bike without panicking or grabbing the brakes so hard the rear wheel locks. Third, they should be riding with their eyes up, looking ahead rather than down at the front wheel—this shows their brain has moved balance to automatic.
A common mistake is removing training wheels because your child can ride in a straight line. Straight-line riding does not require balance; it requires only steering and throttle control. Turns are where balance matters, because the bike leans and your child's weight has to shift to the inside of the turn. If your child is still using the training wheels to stay upright in turns, they are not ready.
If your child has been riding for 40 to 50 hours and still cannot navigate turns without the training wheels touching, do not remove them. Some children's bodies develop balance sense faster than others, and forcing the issue creates fear and risk. Continue riding with training wheels; readiness will come.
Removing the training wheels step by step
The PW50 training wheels bolt to the rear axle on both sides. You will need a 10mm wrench or socket, a socket wrench handle, and a second wrench to hold the axle nut on the opposite side so it does not spin while you loosen the bolts.
First, place the bike on a flat surface or use a bike stand to keep it upright. Locate the training wheel bracket on the left side of the rear axle. The bolt runs through the bracket and into the axle. Hold the axle nut on the opposite side with one wrench while you turn the bolt counterclockwise with the other wrench. Once the bolt is loose, remove it by hand and set it aside with the bracket. Repeat on the right side.
Keep both bolts and brackets in a labeled container. If your child needs training wheels again—or if you have another child who will ride the PW50—you can reinstall them using the same bolts. Do not discard them.
Setting up for the first rides without training wheels
Choose a location with flat, open ground: a parking lot, a wide grass field, or a paved area with no obstacles. Avoid slopes, gravel, or areas with trees or curbs nearby. Your child will fall, and you want the landing to be on flat, soft ground if possible.
Have your child wear a helmet, wrist guards, and knee pads before every ride. Many children instinctively put their hands down when they feel the bike tipping, and wrist guards prevent the scrapes and sprains that come from that reflex. Knee pads protect the same way.
Start by having your child ride slowly in a straight line to get used to the feel of the bike without training wheels. Then practice gentle turns at low speed. Do not rush into faster riding; the goal is for your child's body to learn the automatic weight shifts that keep the bike balanced. This usually takes three to five rides of 15 to 20 minutes each.
What to expect during the learning phase
Your child will fall. Most children fall two to five times during the first few rides without training wheels, and these falls are usually low-speed tips to one side rather than dramatic crashes. The falls happen because your child's brain is still learning to correct balance automatically; they overcorrect, the bike tips the other way, and they go down. This is normal and part of learning.
Do not catch the bike or try to prevent falls. If you hold the bike up, your child's body never learns to make the balance corrections on its own. Let small falls happen; they teach faster than any amount of instruction. Stay close enough to help if your child gets hurt, but do not interfere with the riding itself.
After the first few rides, most children stop falling and start riding with confidence. Some children take longer—a week or two of regular practice—before balance becomes automatic. This variation is normal and does not mean anything is wrong.
Reinstalling training wheels if needed
If your child is not ready to ride without training wheels, or if they are scared after a fall and want them back, reinstall them using the same bolts and brackets. There is no shame in this; it is safer than forcing your child to ride without them before they are ready.
To reinstall, place the training wheel bracket back on the rear axle on both sides. Insert the bolt through the bracket and into the axle hole. Hold the axle nut on the opposite side with one wrench while you tighten the bolt clockwise with the other wrench. Tighten firmly but do not overtighten; you should not need to strain to turn the wrench. Repeat on the other side.
Once reinstalled, check that both training wheels touch the ground evenly and that the bike sits level. If one wheel is higher than the other, loosen that side slightly and adjust until both wheels contact the ground at the same height.
Frequently Asked Questions
Can I adjust the training wheels so they are higher off the ground?
Yes. Some training wheel brackets have adjustment holes that let you raise or lower the wheels. Raising them gradually—so they barely touch the ground—can help your child learn balance while still having them as a safety net. Consult your PW50 owner's manual for the specific adjustment points on your model.
What if my child is afraid to ride without training wheels?
Fear is common and usually fades after the first successful ride. Start in a very open area with no obstacles, ride at very low speed, and let your child practice for short sessions—10 to 15 minutes—rather than long ones. If fear persists after several rides, reinstall the training wheels and try again in a few weeks.
Do I need to adjust anything else on the PW50 after removing training wheels?
No. The suspension, brakes, and throttle do not need adjustment. The only change is the removal of the training wheel brackets and bolts from the rear axle.
How tight should the training wheel bolts be when I reinstall them?
Tight enough that they do not move when you wiggle the training wheel by hand, but not so tight that you have to strain to turn the wrench. Over-tightening can strip the bolt threads or crack the bracket. Hand-tight plus a quarter turn is usually correct.
What if one training wheel is dragging on the ground during turns?
This usually means the training wheels are not adjusted to the same height. Loosen the bolt on the wheel that is dragging, raise it slightly, and retighten. Both wheels should touch the ground evenly when the bike is on flat ground and upright.