What happens when a bolt breaks and why you need to remove it

A broken bolt leaves part of the fastener stuck inside the hole it was supposed to hold. The broken piece won't come out by turning a wrench—it's already snapped. You need to remove it because the hole is now unusable: you can't thread a new bolt into a hole that's already half-full of metal, and leaving it there means that part stays loose or unfastened. A broken bolt in a critical location—engine block, suspension, brake components—creates a safety problem and a reliability problem. The part it was holding can shift, rattle, or fail.

Broken bolts happen most often when you overtighten, when rust has seized the bolt to the hole, or when metal fatigue has weakened the bolt over time. The bolt snaps at the weakest point, usually just below the head or at the threaded section. Once it breaks, the remaining stub is often below the surface of the surrounding metal, making it hard to grab with pliers or a wrench.

Key Takeaways

  • A broken bolt must be removed because the remaining piece blocks the hole and prevents a new bolt from being installed.
  • The safest first step is to try backing out the stub with locking pliers or a screw extractor, which grips the remaining metal and turns it counterclockwise.
  • If the stub won't turn, drilling it out is the next option—use a drill bit slightly smaller than the bolt diameter and drill straight into the center of the stub.
  • Seized or rusted bolts may need penetrating oil applied several hours or overnight before you attempt removal.
  • If the bolt is in a critical location or you strip the hole during removal, a machine shop can often repair the hole by re-threading it to a larger size or installing a threaded insert.

Try backing out the stub with locking pliers or a screw extractor

The easiest removal method works only if enough of the bolt is sticking out to grip. Locking pliers (Vise-Grips) clamp down hard on the remaining stub and can sometimes turn it counterclockwise enough to unscrew it. Clamp as close to the hole as you can, then turn slowly and steadily. If the stub turns even a little, keep going—it may come free.

A screw extractor is a tapered tool designed for this job. You drill a small pilot hole into the center of the bolt stub, then insert the extractor into that hole. As you turn the extractor counterclockwise, its tapered shape bites into the bolt and pulls it out. Extractors come in sets sized for different bolt diameters. This method works well when the stub is too small or too flush to grip with pliers.

If the bolt is rusted or seized, spray penetrating oil (such as PB Blaster or Liquid Wrench) around the base of the stub and let it soak for at least two hours, or overnight if possible. The oil seeps into the threads and reduces friction. Then try the pliers or extractor again.

Drill out the stub if it won't turn

When the stub is too corroded or too short to grip, drilling is the standard approach. Use a drill bit that is slightly smaller than the bolt diameter—for example, if the bolt is 8 millimeters, use a 6 or 6.5 millimeter bit. Mark the center of the bolt with a center punch (a small pointed tool you tap with a hammer) so the drill bit doesn't wander. Clamp or hold the part steady so it doesn't spin.

Drill slowly and straight into the center of the stub. The bit will cut through the bolt material and push the broken piece out the back of the hole. Use cutting fluid or light machine oil to cool the bit and reduce friction—this keeps the bit sharp and helps it cut faster. Stop occasionally to clear chips and reapply oil.

Once the stub is drilled out, the hole is now larger and the threads are damaged. You will need to re-thread the hole or use a threaded insert (a small metal sleeve that creates new threads inside the enlarged hole). A machine shop can do this, or you can buy a threaded insert kit and install it yourself if the bolt is not in a critical structural location.

When to use a threaded insert or re-thread the hole

After drilling out a broken bolt, the hole is oversized and the original threads are gone. A threaded insert (also called a helicoil) is a coiled metal sleeve that screws into the enlarged hole and creates new threads for your bolt. Inserts are sold in kits that include the insert, an installation tool, and a drill bit sized for that insert. They are inexpensive and work well for non-critical fasteners.

To install an insert, you drill the hole to the size specified in the kit, tap new threads into that hole, then screw the insert into those threads. The insert sits flush with the surface, and you then install your bolt into the insert's threads. This restores the hole to working condition.

For critical locations—engine block, suspension mounts, brake components—a machine shop can re-thread the hole to the next larger bolt size. For example, if the original bolt was 8 millimeters, they can re-thread it for a 10 millimeter bolt. This is more expensive than an insert but is the standard repair for safety-critical fasteners. Ask your shop whether the larger bolt will fit the process and whether it will carry the same load.

Avoid common mistakes that make removal harder

Do not use a drill bit that is too large. If you drill too big, you remove too much material and the hole becomes impossible to re-thread or insert. Start with a bit that is noticeably smaller than the bolt diameter and drill carefully down the center. If you wander off-center, you risk enlarging the hole unevenly and damaging the surrounding threads.

Do not force a stuck bolt. If locking pliers or an extractor won't budge it, stop and explore penetrating oil instead. Forcing it risks breaking the tool, stripping the bolt further, or cracking the surrounding part. Patience with penetrating oil is faster in the end.

Do not assume you can install a larger bolt without checking. Some parts have limited space, and a bolt that is one size larger may not fit or may interfere with other components. Confirm with your vehicle's service manual or a shop before drilling.

When to take the part to a machine shop

If the broken bolt is in a critical location—such as an engine block, cylinder head, suspension arm, or brake component—or if you have already stripped the hole during removal, a machine shop is the right choice. Shops have precision tools, experience with damaged holes, and the ability to re-thread or install inserts correctly. They can also assess whether the damage is repairable or whether the part itself needs replacement.

Bring the part and the bolt (if you have it) so the shop can measure and match the size. Tell them where the bolt came from and what it holds, so they understand the load and criticality. A straightforward re-threading or insert installation usually costs between $20 and $50 per hole, depending on location and difficulty. This is far cheaper than replacing a part or dealing with a failure later.

Frequently Asked Questions

Can I just leave the broken bolt in there?

No. The hole is now blocked, so you cannot install a new bolt to hold that part. The part will remain loose or unfastened, which can cause rattling, misalignment, or failure depending on what the bolt was holding. In safety-critical locations like suspension or brakes, a loose part is a serious hazard.

What size drill bit should I use?

Use a bit that is 1 to 2 millimeters smaller than the bolt diameter. For an 8 mm bolt, use a 6 or 6.5 mm bit. This removes the bolt without removing so much material that the hole cannot be re-threaded or repaired. Drill slowly and use cutting fluid to keep the bit cool.

How long does penetrating oil take to work?

Most penetrating oils need at least two to four hours to seep into the threads and reduce corrosion. Overnight soaking (8 to 12 hours) is more effective for heavily rusted bolts. Reapply the oil if it dries out, and let it soak again before attempting removal.

Is a threaded insert as strong as the original bolt?

A properly installed insert is as strong as the original hole for most applications. Inserts are rated for the same load as the bolt size they accommodate. However, for critical structural fasteners, a machine shop re-threading to a larger bolt size is the preferred repair because it uses the full material of the part rather than a sleeve.

What if I drill through the back of the part?

If the part is thin or you drill too deep, you may break through to the other side. This ruins the part if it is a sealed component like an oil pan or transmission case. Always know the thickness of the part and the depth of the hole before you drill. If you are unsure, ask a shop or consult the service manual.