RV awning replacement is a job you can do yourself if the frame is sound, but it requires specific tools, accurate measurements, and several hours of work

An RV awning that tears, won't retract, or shows permanent sun damage needs replacing. You have two paths: remove and reinstall the existing frame yourself with new fabric, or hire an RV service center to do both. The frame itself—the aluminum arms, roller tube, and mounting brackets—usually lasts 15 to 20 years. The fabric fails first, typically after 5 to 10 years of sun exposure. If your frame is straight and the motor or hand crank still works, you can buy replacement fabric and install it yourself for $200 to $600. If the frame is bent, the motor is dead, or you want the job done in a day, a shop will charge $800 to $2,500 depending on awning size and whether they're replacing the whole unit or just the fabric.

The choice between fabric-only and full replacement depends on the condition of your frame and your comfort level with tools. Most RV owners who attempt this work choose fabric-only replacement because it's cheaper and the frame is usually still sound. However, if you've never removed an awning before, hiring a shop saves time and eliminates the risk of damaging the frame or mounting brackets during removal.

Key Takeaways

  • Measure your awning width, projection (how far it extends), and the exact model number before ordering replacement fabric or a new awning.
  • Fabric-only replacement costs $200 to $600 and takes 4 to 6 hours if you have basic tools and the frame is undamaged.
  • Full awning replacement (frame and fabric) runs $800 to $2,500 at a shop and is the better choice if the frame is bent, the motor doesn't work, or you lack tools.
  • RV service centers, dealerships, and independent awning shops all perform replacements; get quotes from at least two before deciding.
  • You will need a ladder, socket set, screwdrivers, a drill, and a helper to safely remove or reinstall an awning.

Measure your awning before ordering anything

The most common mistake is ordering the wrong size. RV awnings are sold by width (the measurement across your RV side) and projection (how far the fabric extends when open). Write down both numbers before you contact a supplier or shop. The width is usually printed on a sticker on the awning roller tube itself, or on the mounting bracket. If you can't find it, measure the distance between the two mounting brackets on your RV wall. Projection is trickier—it's the distance from the RV wall to the outer edge of the fabric when fully extended, not the length of the arms. If you're unsure, take a photo of the awning fully open from the side and bring it to a shop or email it to the supplier.

Also locate your awning model number. It's usually on a label attached to the roller tube or the motor housing. Write it down exactly as printed. When you call a supplier or shop, give them the width, projection, and model number. They can then tell you whether replacement fabric exists for your frame, or whether you need a full new awning. Some older or less common models have fabric no longer made, which means you'll have to replace the whole unit. Having this information ready before you call saves time and prevents you from ordering parts that won't fit.

Decide between fabric-only replacement and full awning replacement

If the frame is straight, the arms move smoothly, and the motor or hand crank works, fabric-only replacement is the cheaper and faster option. You'll remove the old fabric from the roller tube, slide the new fabric on, and reinstall the awning. This takes 4 to 6 hours with a helper and basic tools. The fabric itself costs $200 to $600 depending on size and material (vinyl is cheaper and more common; acrylic is more durable and resists fading better). Fabric-only replacement makes sense if the awning is less than 10 years old and the only problem is sun damage or a tear.

If the frame is bent, the motor is broken, the arms stick or won't retract smoothly, or you don't have the tools or confidence to do the work, buy a full replacement awning. A new awning includes the roller tube, arms, brackets, motor or hand crank, and fabric all assembled. Prices range from $800 to $2,500 installed, depending on awning size and whether you choose a manual or motorized model. A shop will remove the old awning, install the new one, test it, and seal the mounting holes. This takes one day and requires no work from you. Full replacement is also the better choice if your awning is more than 15 years old, because the frame may fail soon even if it looks fine now.

Steps to replace awning fabric yourself

Start by retracting the awning fully and disconnecting power to the motor (flip the breaker or unplug the cord). You'll need a ladder, a socket set, screwdrivers, a drill, and a helper. Have the new fabric rolled and ready before you start. Clear a large flat work area—a driveway or parking lot works well—where you can lay the awning frame while you work on it.

First, remove the end caps (the plastic or metal covers on each end of the roller tube). They're usually held by one or two screws. Next, unbolt the awning from the RV wall. There are typically four bolts—two at the top and two at the bottom of each mounting bracket. Use a socket wrench to remove them. Have your helper support the awning frame as you unbolt it, because it's heavy and will fall if not held. Lower it carefully to the ground or a work table. Do not attempt this alone; a falling awning frame can cause serious injury.

Lay the awning on a flat surface. The fabric is sewn or glued to the roller tube and held in place by a rubber or plastic strip that runs along the edge. You'll need to peel back this strip (called a rail or extrusion) to free the old fabric. Use a flathead screwdriver to gently pry it up, working slowly so you don't damage the tube. Once the rail is loose, pull the old fabric off the tube. Clean any glue or debris from the tube with a cloth and rubbing alcohol. This step is important because old glue or dirt will prevent the new fabric from sitting evenly.

Slide the new fabric onto the roller tube, aligning it so the edges are even on both sides. Press it down firmly. Then press the rail back into place over the fabric edge, working from one end to the other. If the rail is stubborn, tap it gently with a rubber mallet. Once the fabric is find, reinstall the end caps and bolt the awning back to the RV wall. Have your helper hold it level while you tighten the bolts. Test the awning by retracting and extending it a few times before you consider the job done. If it binds or doesn't move smoothly, stop and check that the fabric is seated evenly on the roller tube.

Hiring a shop to replace your awning

Call three to five shops in your area and ask for quotes. Tell them your RV model, awning width and projection, and whether you want fabric-only replacement or a full new awning. Ask whether they stock the part or need to order it, and how long installation takes. Most shops can install a full awning in one day; fabric-only replacement may take two to three days if they have to order the fabric. Getting multiple quotes helps you understand the market price and find a shop that fits your budget and timeline.

RV dealerships often handle awning work, but they may charge more than independent shops. Independent RV service centers and awning specialists are usually cheaper and may have faster turnaround. Ask each shop whether the price includes removal of the old awning, installation, testing, and sealing. Some shops charge extra for removal or for sealing the mounting holes after installation. Get the quote in writing before you leave the RV with them. A written quote protects you from surprise charges when you pick up the RV.

While the awning is being replaced, ask the shop to inspect the mounting brackets and the wall around them for water damage or rust. If water has been leaking around the old awning, the wall may need repair before the new awning is installed. This is an extra cost, but catching it now prevents bigger problems later. Water damage can weaken the RV wall and lead to structural issues if left untreated, so it's worth addressing while the awning is off.

Maintenance to extend your awning's life

Clean the fabric twice a year with mild soap and water to remove dirt and mildew. Rinse thoroughly and let it dry completely before retracting. Never use a pressure washer, which can tear the fabric or force water into the seams. Retract the awning during high winds or storms—fabric can tear and the frame can bend if the awning catches wind. If you live in a very sunny climate, consider a protective coating designed for RV awning fabric; these can slow fading and extend fabric life by a few years. Regular cleaning also helps you spot small tears early, before they become large enough to require replacement.

Check the mounting bolts twice a year and tighten any that have loosened. Vibration from driving can work bolts loose over time. If you notice the awning is harder to extend or retract, or if the fabric is sticking, the roller tube may need lubrication. Use a silicone-based lubricant (not WD-40, which attracts dirt) and explore it sparingly to the roller tube and the arm hinges. Proper maintenance can add two to three years to your awning's life and prevent costly repairs down the road.

Frequently Asked Questions

Can I patch a torn awning instead of replacing it?

Small tears (under 2 inches) can be patched with a vinyl repair kit from an RV or marine supplier, but patches are temporary and visible. Large tears, multiple tears, or tears along a seam usually mean the fabric is near the end of its life and replacement is the better choice. Patches also weaken the fabric around the repair, so another tear often follows nearby.

How long does a new awning last?

Fabric typically lasts 5 to 10 years depending on sun exposure, climate, and maintenance. Frames last 15 to 20 years if they're not bent or damaged. In very sunny climates (Arizona, Southern California), fabric may fade and crack in 4 to 6 years. In cooler or cloudier regions, it may last 10 to 12 years.

Do I need to seal the mounting holes after the old awning is removed?

Yes. The old mounting bolts leave holes in the RV wall, and water can leak through them if left open. A shop will seal them with caulk or new bolts as part of installation. If you remove an awning yourself, seal the holes with marine-grade silicone caulk before installing a new awning.

What's the difference between manual and motorized awnings?

Manual awnings have a hand crank you turn to extend and retract the fabric. Motorized awnings have an electric motor and a switch or remote. Motorized awnings cost $300 to $800 more but are easier to use, especially for larger awnings. If your old awning was motorized and the motor works, you can keep it and just replace the fabric.

Can I install a larger awning than the one I'm replacing?

Only if your RV's wall can support it and the new awning's mounting brackets fit your existing holes. Larger awnings are heavier and put more stress on the wall. Talk to a shop before ordering a larger awning—they can tell you whether it's safe for your RV model and what modifications, if any, are needed.