You can replace a RAM key fob battery yourself in about five minutes with a coin and a fresh battery
RAM key fobs use a standard coin-cell battery that you can buy at any drugstore or supermarket for $3 to $8. The fob itself doesn't need to be taken to a dealer — you open it with a coin, swap out the old battery, and close it back up. The whole job takes longer to find the right battery type than to do the replacement.
The battery type varies by model year and fob design. Most RAM trucks from 2009 onward use either a CR2032 or CR2025 battery. Your owner's manual lists the exact type, or you can check the battery compartment itself — the old battery will have the type printed on it.
Key Takeaways
- RAM key fob batteries are standard coin-cell types (usually CR2032 or CR2025) sold at any pharmacy or grocery store for a few dollars.
- Open the fob by inserting a coin into the slot on the edge and twisting gently until the two halves separate.
- Note which side of the battery faces up before you remove it, then insert the new battery the same way.
- Test the fob before you put it back together completely to confirm the new battery works.
- If the fob still doesn't work after a fresh battery, the problem is likely the circuit board or buttons, not the power source.
Finding the right battery type for your RAM fob
Check your owner's manual first — it will specify the battery model. If you don't have the manual, open the fob and look at the old battery. The type is stamped on the metal side: CR2032, CR2025, or occasionally CR2016. Write down the number before you go to the store.
If you can't open the fob to see the old battery, call a RAM dealer parts department with your truck's year and model. They can tell you the battery type in one call. You don't need to buy the battery from them — any pharmacy or grocery store carries these standard types.
CR2032 is the most common in RAM fobs. It's thicker than CR2025 but both are the same diameter. Using the wrong thickness can prevent the fob from closing properly or cause poor contact with the battery terminals.
How to open the fob without damaging it
Look at the edge of your fob for a small slot or seam. This is where the two plastic halves meet. Insert a coin — a dime or penny works — into the slot and twist gently. You're not trying to pry it open; you're using the coin as a lever to separate the halves.
Turn the coin slowly and steadily. The fob will crack open after a quarter-turn or so. If it doesn't budge after gentle pressure, try a different spot along the seam — some fobs have the slot on the side, others on the top edge.
Once the fob opens, you'll see the battery sitting in a small metal cradle. The battery is usually held in place by the spring tension of the cradle itself, not by any clip or screw. Gently lift one edge of the battery to pop it out.
Removing the old battery and installing the new one
Before you remove the old battery, note which side faces up. The positive side (marked with a + symbol) should face the same direction in the new battery. This matters — if you install it backward, the fob won't work.
Lift the battery out of the cradle and set it aside. Clean the metal contacts inside the cradle with a dry cloth or cotton swab if you see any corrosion or debris. Corrosion on the contacts is a common reason a fob stops working even with a fresh battery.
Insert the new battery with the positive side facing the same direction as the old one. Press down gently until it sits flat in the cradle. The battery should fit snugly without forcing it.
Testing the fob before closing it
Before you snap the fob back together, press each button — lock, unlock, panic, trunk, or whatever buttons your fob has. You should hear a click or feel a slight vibration from the truck, or see the lights flash. If nothing happens, the battery may be installed backward or the contacts may need cleaning.
If the buttons don't work, remove the battery, flip it around, and try again. If it still doesn't work after reversing the battery, remove it and inspect the metal contacts in the cradle. If they're corroded or damaged, the fob may need professional repair or replacement.
Closing the fob and confirming it works
Once the buttons respond, align the two halves of the fob and press them together. You should hear a click when they seat properly. The seam should be even all the way around — if one side is higher than the other, the halves aren't fully closed.
Test the fob one more time from a few feet away from your truck to confirm it still works after closing. Press each button and watch for the truck's lights to flash or hear the locks engage. If the fob worked with the halves open but stops working when closed, the battery may not be making good contact — open it again and reseat the battery.
What to do if a new battery doesn't fix the problem
A dead battery is the most common reason a RAM key fob stops responding, but it's not the only one. If a fresh battery doesn't restore the fob's function, the problem is likely inside the fob itself — a worn button contact, a cracked circuit board, or corrosion on the internal components.
You can try cleaning the battery contacts and the underside of the buttons with a cotton swab and rubbing alcohol, then letting everything dry completely before reassembling. This sometimes restores function if corrosion is the culprit.
If cleaning doesn't work, the fob will need to be replaced. RAM dealers sell replacement fobs, and you can also find aftermarket fobs online. A replacement fob typically costs $50 to $150 depending on the model year. Most fobs sold by dealers come pre-programmed, but some require programming at a dealership — ask before you buy.
Frequently Asked Questions
How often do RAM key fob batteries need to be replaced?
Most coin-cell batteries last two to four years in a key fob, depending on how often you use it. If you press the buttons dozens of times a day, the battery will drain faster than if you use the fob once or twice daily. When the fob starts responding slowly or requires multiple button presses, it's time for a new battery.
Can I use a rechargeable battery in my RAM fob?
No. Rechargeable coin-cell batteries have a different voltage than standard alkaline batteries and can damage the fob's circuit board or cause it to malfunction. Stick with the standard alkaline type listed in your manual.
What if I lost my owner's manual and can't find the battery type?
Call a RAM dealer parts department with your truck's year, make, and model. They can tell you the battery type without charging you. You can also try opening the fob gently with a coin and looking at the old battery — the type is printed on it.
Does the fob need to be reprogrammed after I change the battery?
No. Changing the battery does not erase the fob's programming. It will work when ready once you install the new battery and close the fob.
Why does my fob work sometimes but not other times after a battery change?
Intermittent function usually means the battery isn't making solid contact with the terminals. Open the fob, remove the battery, and clean both the battery and the metal cradle with a dry cloth. Reinstall the battery and press it down firmly to may support good contact.