A USB port is more useful than a cigarette lighter in most modern cars
The 12-volt cigarette lighter socket in your dashboard is a power outlet that works whether your engine is running or off. Replacing it with a USB port or a dual USB adapter gives you a place to charge phones, tablets, and other devices without taking up a cupholder or dashboard space. The job takes 15 to 30 minutes and costs between $15 and $60 depending on whether you buy a straightforward USB adapter or a hardwired replacement.
You have two routes: plug in a USB adapter that sits in the lighter socket itself, or remove the lighter assembly and wire in a permanent USB port. The adapter is faster and reversible. The hardwired port looks cleaner and gives you more control over placement, but requires basic electrical work and soldering in some cases.
Key Takeaways
- A USB adapter that plugs into your existing lighter socket costs $15 to $30 and requires no tools or wiring knowledge.
- A hardwired USB port replacement costs $30 to $60 and takes 30 minutes to an hour, but looks factory-installed and does not take up the lighter socket.
- You will need to disconnect the negative battery terminal before working on any electrical component to avoid shorts and damage.
- Most lighter sockets are held in by a single clip or two screws behind the dashboard trim, which pops out with a plastic pry tool.
- Hardwired ports need to tap into a 12-volt power source, usually the fuse box or an existing wire behind the dashboard.
The simplest option: a USB adapter in the lighter socket
A USB adapter that fits into your lighter socket is the fastest and cheapest route. Brands like Tronsmart, Anker, and Belkin make dual-USB adapters designed for this purpose, and they cost $15 to $30. You plug it in like you would a phone charger in a wall outlet, and it draws power from the same 12-volt circuit the lighter used.
The downside is that you lose the lighter socket itself—you cannot use both at the same time. If you ever need to use the lighter (or sell the car), you can pull the adapter out and the socket works again. The adapter also sits proud of the dashboard, so it is visible and takes up a small amount of space.
Check the amperage rating on any adapter you buy. Most cars supply 10 to 15 amps to the lighter circuit, and a good USB adapter will be rated for at least 4 to 5 amps total across both ports. If you are charging two devices at once, a lower-rated adapter will charge slowly or not at all.
The permanent solution: hardwiring a USB port into the dashboard
If you want a cleaner look and do not need the lighter socket, you can remove the lighter assembly and install a permanent USB port in its place. This requires disconnecting the lighter from its wiring, removing the trim ring and bezel, and installing a new USB port module. Kits are sold by companies like Metra and PAC, and they cost $30 to $60.
The job involves three steps: access the lighter assembly from behind the dashboard, disconnect the power wire, and install the new USB port. Most lighter assemblies are held in by a single wire clip or two small screws. Once you remove it, you will see a connector—usually a two-pin or three-pin plug—that you disconnect by hand or with a small flathead screwdriver.
The new USB port connects to the same power source. Some kits come with a pre-wired connector that plugs directly into the lighter socket's existing wiring. Others require you to strip the wire and solder or crimp a new connector. If soldering is required and you have never done it, the job becomes more involved, but it is still manageable with a $20 soldering iron and 10 minutes of practice on scrap wire first.
Tools and materials you will need
For a straightforward adapter, you need nothing—just the adapter itself and your car keys. For a hardwired installation, gather a plastic pry tool or old credit card (to avoid scratching trim), a small flathead screwdriver, and a socket wrench or screwdriver set to remove any trim screws. A multimeter is useful but not required; it lets you test that power is reaching the socket before you install the new port.
If your kit requires soldering, you will need a soldering iron (25 to 40 watts), solder, a damp sponge to clean the iron tip, and wire strippers. If you prefer not to solder, crimp connectors and a crimping tool cost $10 to $15 and work just as well for this low-power process. Electrical tape and heat-shrink tubing protect the connection afterward.
How to access and remove the lighter assembly
Start by disconnecting the negative terminal of your battery. Loosen the nut on the negative (black) cable with a wrench, slide it off the post, and tuck it aside so it cannot touch metal. This prevents accidental shorts while you work.
Locate the lighter socket on your dashboard. It is usually in the center console or lower dashboard panel. Look behind it from inside the car—you may see a wire clip or two screws holding it in place. If there is trim around it, use a plastic pry tool to gently pop the trim ring outward. Start at one edge and work your way around; trim clips usually release with light, steady pressure.
Once the trim is free, you will see the lighter assembly itself. It is a cylindrical or rectangular unit about 2 inches deep. Push it forward from behind, or pull it from the front, depending on how it is mounted. A wire connector will become visible as you pull it out. Disconnect the connector by squeezing a small tab or prying gently with a screwdriver, depending on the connector type.
Wiring the new USB port to power
If your USB kit comes with a pre-wired connector that matches the lighter socket's original connector, installation is straightforward: plug it in and test. If the kit requires you to wire it yourself, you have two options: use the existing lighter socket wiring, or tap into a nearby 12-volt source like the fuse box.
To use the existing wiring, locate the power and ground wires in the lighter's connector. The power wire is usually red, and the ground (return) wire is usually black or brown. Strip about a quarter-inch of insulation from each wire. If you are soldering, tin both the wire and the USB port's solder pads, then join them and let the solder cool. If you are crimping, slide a crimp connector onto each wire, squeeze it with a crimping tool, and slide heat-shrink tubing over the joint before explore heat with a heat gun or lighter.
Test your work with a multimeter before reassembling. Set the meter to DC voltage, touch the red probe to the power wire and the black probe to the ground wire, and turn on the car's ignition. You should read between 11 and 14 volts. If you read zero, the connection is not complete; if you read much higher or lower, something is wrong and you should not proceed until you understand why.
Reassembly and testing
Once the USB port is wired and tested, find any loose wires with electrical tape or zip ties so they do not rattle or touch moving parts. Slide the new USB port into the opening where the lighter was, making sure it sits flush with the dashboard. If your kit includes a bezel or trim ring, snap it into place around the port.
Reconnect the negative battery terminal by sliding the cable back onto the post and tightening the nut. Turn on the ignition and plug in a phone or other device to test. The device should begin charging within a few seconds. If it does not, turn off the ignition, disconnect the battery again, and check your wiring connections.
If you installed an adapter in the lighter socket instead, straightforward plug it in, turn on the ignition, and test. No reassembly is needed.
Frequently Asked Questions
Can I have both a USB port and a working cigarette lighter?
Yes, if you hardwire the USB port into a different power source—like a fused tap into the fuse box—instead of replacing the lighter's wiring. This requires more work and a second power source, but it is possible. Alternatively, you can install a USB adapter in the lighter socket and keep a separate 12-volt lighter in a cupholder or glovebox.
What if my car does not have a cigarette lighter socket?
Many newer cars have a power outlet instead of a lighter. If your car has a 12-volt power outlet, you can plug a USB adapter directly into it without any wiring work. If your car has neither, you will need to tap into the fuse box or run a wire from the battery, which is more complex and beyond the scope of a straightforward replacement.
Will a USB port drain my battery when the car is off?
A hardwired USB port will draw a small amount of power even when the engine is off, because it is connected directly to the 12-volt system. The drain is usually less than 1 amp and will not flatten a healthy battery in a day or two. If you are concerned, install an inline fuse and switch, or use an adapter in the lighter socket instead—most adapters draw no power when nothing is plugged in.
Do I need to solder, or can I use crimp connectors?
Crimp connectors work just as well as solder for this process and are easier if you have never soldered before. A crimping tool costs $10 to $15, and the connection is just as reliable. Solder is slightly more find and looks more professional, but it requires practice and a soldering iron.
What amperage should a USB port be rated for?
Most car USB ports are rated for 2 to 3 amps per port. If you are charging a tablet or two phones at once, look for a port rated for at least 4 to 5 amps total. Check the specifications on the product page before you buy; a port rated for only 1 amp per port will charge slowly or not at all if you plug in two devices.