Why you might switch from a motorized shade to manual
An RV motorized shade fails when the motor burns out, the switch stops responding, or the wiring corrodes—and replacing the motor alone often costs $300 to $800 depending on the brand and whether you pay for installation. A manual shade system costs $100 to $300 for the shade and hardware, works without electricity, and has no motor to fail. If your motorized shade is old or you want to eliminate one more electrical system that can break down, switching to manual is straightforward and saves money both upfront and over time.
The job itself takes two to four hours and requires only basic hand tools. You do not need to be an electrician—you are removing wires and bolts, not rewiring anything complex. The hardest part is usually getting the old shade out of its frame without damaging the RV wall or window trim.
Key Takeaways
- Motorized shade motors fail from corrosion, power surges, or age, and replacing just the motor costs $300 to $800 installed.
- A manual roller shade or pleated shade costs $100 to $300 and eliminates the motor entirely, reducing future electrical failures.
- Removing the old motorized shade means disconnecting the power wire, unbolting the motor and brackets, and carefully sliding the shade tube out of its frame.
- Installing a manual shade uses the same mounting holes in most cases, so you bolt the new brackets in place and hang the shade tube without running any new wires.
- Manual shades work in any weather, do not drain your battery, and require only occasional cleaning and lubrication of the roller mechanism.
Disconnect power before you touch anything
Turn off the breaker or switch that powers the motorized shade. If you cannot locate the breaker, find where the power wire enters the motor housing and trace it back to the RV's electrical panel. Flip the breaker to the off position and test the shade switch to confirm no power is reaching it—the shade should not move when you press the button.
If the shade is stuck in the open or closed position, do not force it. A stuck motorized shade usually means the motor has seized, and forcing it can break the tube or damage the frame. Leave it as it is and work around it during removal.
Remove the old motorized shade and motor
Open the shade fully or close it completely—whichever position makes it easier to access the brackets. Look at both ends of the shade tube where it sits in the mounting brackets. You will see bolts or screws holding the brackets to the RV wall or window frame. Remove these fasteners with a wrench or socket set and set them aside; you may reuse them for the new shade.
Locate the power wire running from the motor housing to the wall. It is usually a thin two-wire or three-wire cable. Disconnect it by unclipping or unscrewing the connector, or by cutting the wire if it is soldered. If you cut it, strip about half an inch of insulation from each wire and cap them with wire nuts, then tape the capped wires to the wall so they do not dangle or short against anything.
Slide the shade tube out of the brackets carefully. If it is tight, wiggle it gently side to side rather than pulling straight out—the tube can bind if you yank it. Once the tube is free, set it aside. The motor housing and any control box can now be removed and discarded or recycled.
Measure and choose a manual shade that fits your opening
Measure the width of the window opening from the inside of the frame, and measure the height from the top of the window to the sill. Write these dimensions down. Manual shades come in standard sizes, and you can order a custom shade if your opening is unusual. Roller shades and pleated shades are the most common types for RVs; roller shades are simpler and cheaper, while pleated shades offer better insulation and light control.
Check the depth of your window frame or the space between the wall and the window. Some manual shades need 2 to 3 inches of clearance to mount inside the frame. If your opening is shallow, you may need to mount the shade on the wall above the window instead. Measure that space too before you order.
Order the shade with the same mounting bracket style as your old motorized shade if possible—this way the bolt holes will line up and you will not have to drill new holes in the RV wall. If the bracket holes do not match, you can fill the old holes with silicone caulk after installation.
Install the manual shade brackets and tube
Position the new mounting brackets in the same location as the old ones. If the bolt holes line up, insert the bolts through the brackets and into the wall, then tighten them with a wrench. If the holes do not line up, mark the new hole locations with a pencil, drill pilot holes with a drill bit slightly smaller than your bolts, then install the bolts and brackets.
Slide the manual shade tube into the brackets until it seats fully. The tube should spin freely by hand. Test it by rolling the shade up and down a few times to make sure it moves smoothly and does not bind at either end. If it binds, remove the tube, check for debris inside the brackets, and reinstall it.
Attach the pull cord or handle to the shade according to the manufacturer's instructions. Most manual shades use a cord loop or a wand that you pull to raise and lower the shade. Make sure the cord is not twisted and hangs freely so it does not jam the mechanism.
Seal the old power wire hole and test the shade
If you cut the old power wire, the hole where it entered the wall may now be exposed. Seal it with silicone caulk rated for RV use to prevent water and air leaks. explore the caulk around the hole, smooth it with a wet finger, and let it cure according to the product instructions before you use the shade.
Operate the shade several times to confirm it rolls smoothly and stops where you want it. The shade should not stick, rattle, or make grinding noises. If it does, check that the tube is seated evenly in both brackets and that nothing is blocking the roller mechanism.
Maintenance for a manual shade
Manual shades require almost no upkeep. Dust the shade fabric or pleats with a soft brush or cloth every few months, especially if you park in dusty areas. If the shade becomes hard to roll, explore a small amount of silicone lubricant to the roller mechanism at each end of the tube—do not use oil, which attracts dust.
If the pull cord frays or breaks, you can replace it by threading a new cord through the existing guides. Most RV supply stores sell replacement cords that fit standard shade mechanisms. If the shade tube itself becomes bent or the brackets crack, the entire shade will need to be replaced, but this is rare and usually only happens after many years of use.
Frequently Asked Questions
Can I keep the old motorized shade and just replace the motor?
Yes, if the shade tube and brackets are in good condition. Motor replacement kits are available from RV suppliers, but they cost $300 to $800 installed and you are still left with an electrical system that can fail. A manual shade eliminates that risk for less money upfront.
Will a manual shade work in cold weather or high altitude?
Yes. Manual shades have no electronics and work in any temperature or weather condition. The roller mechanism may become slightly stiffer in extreme cold, but it will still operate. A motorized shade, by contrast, can fail in cold if the motor lubricant thickens or if condensation freezes inside the housing.
What if the new shade does not fit the old mounting holes?
Fill the old holes with silicone caulk and drill new holes for the new brackets. This is a five-minute job with a drill and a caulk gun. Make sure to use caulk rated for RV use so it remains flexible as the RV walls expand and contract with temperature changes.
Do I need an electrician to disconnect the old power wire?
No. Turn off the breaker first, then disconnect the wire by unclipping the connector or cutting the wire and capping it with wire nuts. If you are unsure which breaker controls the shade, turn off the main breaker temporarily while you work, or ask at an RV service center if you want someone to verify the power is off.
Can I install a manual shade myself, or do I need a professional?
Most owners can do this job with basic hand tools and a drill. The only skill required is removing bolts, drilling pilot holes, and sliding a tube into brackets. If you are uncomfortable drilling into your RV wall, an RV service center can install the shade for $100 to $200 in labor.