What a rivnut install tool does and why it matters
A rivnut install tool is a handheld device that installs threaded metal inserts (called rivnuts or rivet nuts) into thin sheet metal or composite materials. The tool pulls a mandrel through the insert, which expands the rivnut against the back side of the material and locks it in place. Once installed, the rivnut gives you a permanent threaded hole you can bolt into repeatedly without the threads stripping out.
On a car, rivnuts show up most often in body panels, trim pieces, and aftermarket accessories where you need a bolt hole but the base material is too thin to tap threads directly. Without a rivnut, you'd either strip the hole after a few bolt cycles or have to use a nut and bolt through both sides—which doesn't work when you only have access to one side of the panel.
The tool itself is mechanical, not powered. You insert the rivnut into the tool's nose, position it over your pre-drilled hole, squeeze the handles together, and the tool does the work. Most automotive rivnut tools cost between $20 and $60 for a basic manual version, and they're reusable for hundreds of installations.
Key Takeaways
- A rivnut install tool creates a permanent threaded hole in thin metal by expanding a metal insert against the back of the material.
- You need a pre-drilled hole the exact size of the rivnut's shaft before you can install one, and that size varies by rivnut diameter.
- Manual squeeze tools work for most car repairs; pneumatic or electric versions exist but are overkill for occasional home work.
- The rivnut must be fully seated and the mandrel must break off cleanly, or the insert won't hold load properly.
- Common failures happen when the hole is drilled too large, the rivnut is installed backwards, or the tool is released before the mandrel snaps.
Choosing the right rivnut size and tool type
Rivnuts come in metric and imperial sizes, and the diameter of the threaded hole they create ranges from M3 (3 millimeters) to M10 (10 millimeters) and larger. The most common automotive sizes are M4, M5, M6, and M8. Before you buy a tool, you need to know what size hole you're installing into—not the bolt you plan to use, but the rivnut itself.
Most manual install tools are sold as kits that include multiple nose pieces (called mandrels or setting dies) to handle several rivnut sizes. A typical $30 to $50 kit will include mandrels for M3 through M8, which covers nearly every car repair situation. Specialty tools for larger sizes exist but are rarely needed for vehicle work.
Manual squeeze tools are the standard for home and shop use. You hold the tool in both hands, position the rivnut in the hole, and squeeze the handles together until they close completely and the mandrel breaks off inside the tool. Pneumatic (air-powered) and electric versions exist for high-volume production work, but they're expensive and unnecessary for occasional repairs.
How to drill the hole and prepare the material
The hole size must match the rivnut's shaft diameter exactly. If the hole is too large, the rivnut won't expand properly and will spin or pull through. If it's too small, you won't be able to insert the rivnut at all. Most rivnut packages include a drill size recommendation—for example, an M5 rivnut typically requires a 5.2 or 5.3 millimeter drill bit.
Mark your hole location with a center punch to keep the drill bit from wandering. Use a drill press or hand drill held as straight as possible—a hole drilled at an angle will cause the rivnut to sit crooked and may not seal or hold load properly. Drill completely through the material; the rivnut needs clearance on the back side to expand.
Clean away any burrs or debris around the hole with a file or deburring tool. Burrs can prevent the rivnut from sitting flush and can interfere with the expansion process. If you're working on painted or coated material, the rivnut will sit on top of the coating, which can prevent a tight fit. For critical sealing applications, you may need to remove the coating around the hole first.
Step-by-step installation process
Start by selecting the correct mandrel (nose piece) for your rivnut size. Insert the mandrel into the tool's nose if it's removable, or verify it's the right size if it's fixed. Insert the rivnut into the mandrel with the threaded end facing outward—this is the end that will stick out of the finished hole.
Position the tool over your drilled hole and push the rivnut into the hole. The rivnut should sit flush with the surface of the material. Squeeze the tool handles together smoothly and steadily. You'll feel resistance as the mandrel pulls the rivnut's internal mandrel (the part that expands it) through the insert. Keep squeezing until the handles close completely and you hear or feel a snap—that's the internal mandrel breaking off.
Release the handles and remove the tool. The rivnut should now be permanently seated in the hole. You can test it by trying to turn it with your fingers—it should not spin. If it does spin, the installation failed and you'll need to drill out the rivnut and start over with a new one.
Common installation mistakes and how to avoid them
The most frequent error is drilling the hole too large. Even 0.5 millimeters oversized can cause the rivnut to slip through without expanding. Always use the exact drill size recommended by the rivnut manufacturer, and if you're unsure, drill a test hole in scrap material first. A slightly undersized hole is better than an oversized one—you can usually force the rivnut in with the tool.
Installing the rivnut backwards (threaded end facing inward) is the second most common mistake. The threaded end must face outward so you can bolt into it. Some rivnuts look similar from both ends, so double-check before you insert it into the tool.
Releasing the tool handles before the mandrel snaps off will leave the rivnut partially expanded and weak. The mandrel must break cleanly inside the tool for the rivnut to lock properly. If you're not sure whether it snapped, squeeze a little harder—the handles should close completely without resistance once the mandrel breaks.
Working on material that's too thick or too hard can also cause failure. Rivnuts are designed for sheet metal, plastic, and composite materials typically 1 to 3 millimeters thick. If your material is thicker than the rivnut's grip range, the tool won't expand it fully and it will pull through under load.
When to use a rivnut versus other fastening methods
Use a rivnut when you need a reusable threaded hole in thin material that you'll bolt into multiple times. Trim clips, badge holders, aftermarket spoilers, and interior panel fasteners are all good candidates. If you only need to fasten something once, a rivet or a bolt-through with a nut on the back side may be simpler.
If the material is thick enough to tap threads directly (usually 3 millimeters or more of solid material), you don't need a rivnut—just drill and tap the hole. If you need a permanent non-threaded fastener, a solid rivet is cheaper and faster. If you need to remove and reinstall the fastener frequently, a rivnut is better than a rivet but a bolt-through with a nut is more reliable if space allows.
Rivnuts are also useful for repairing stripped holes. If a bolt hole in a panel has been stripped by repeated tightening and loosening, you can drill it out slightly larger, install a larger rivnut, and have a fresh threaded hole that will hold for years.
Tool maintenance and storage
Manual rivnut tools require almost no maintenance. After each use, wipe away any metal debris or dust with a dry cloth. If the handles become stiff or squeaky, a light spray of general-purpose lubricant on the pivot point will restore smooth operation. Do not soak the tool in water or leave it exposed to rain—rust on the internal mandrel will cause it to stick or break prematurely.
Store the tool in a dry place, ideally with the mandrels in a small pouch or box so they don't get lost. If you have a kit with multiple mandrels, label them or keep them organized by size so you grab the right one quickly. A tool that sits unused for months will work fine when you need it again, as long as it's been kept dry.
Frequently Asked Questions
Can I install a rivnut if I only have access to one side of the material?
Yes—that's the whole point of a rivnut. The tool expands the insert against the back side of the material from the front, so you only need access to one side. This is why rivnuts are common in car body panels and trim where you can't reach behind the material with a wrench.
What happens if the rivnut spins after I install it?
The installation failed. The rivnut did not expand properly, usually because the hole was drilled too large or the mandrel did not break off cleanly. You'll need to drill out the failed rivnut and install a new one. Use a drill bit slightly larger than the rivnut shaft and carefully drill straight through the center to avoid damaging the surrounding material.
Can I reuse a rivnut if I remove it?
No. Once a rivnut is installed and the mandrel breaks off, the insert is permanently expanded and locked in place. If you remove the bolt and want to reinstall it, you can use the same hole and rivnut. But if you drill out the rivnut to remove it, you cannot reinstall that same rivnut—you'll need a new one in a larger size.
Do I need a power tool version for car work?
No. A manual squeeze tool is sufficient for all typical automotive repairs. Pneumatic and electric tools are faster for high-volume work but cost significantly more and are overkill for occasional home maintenance or small shop jobs.
What size rivnut do I need if I don't know the original size?
Look at the bolt you plan to use. If it's an M5 bolt, you need an M5 rivnut. The rivnut's threaded hole must match the bolt diameter. If you're replacing a stripped hole and don't know the original size, measure the bolt hole with calipers or compare it to a known bolt size before you drill.