RV awnings wear out from sun, wind, and weather — replacement usually means removing the old one, measuring the opening, ordering a new unit, and bolting it in place
An RV awning typically lasts 5 to 10 years depending on how often you use it and how much sun and rain it takes. When the fabric tears, the motor fails, or the frame bends, you have two paths: replace it yourself if you have basic tools and mechanical confidence, or hire a shop to do it. A full replacement (awning unit plus labor) costs between $1,500 and $4,000 at most RV service centers, though the awning alone runs $800 to $2,500 depending on size and type.
The job itself is not complicated — you unbolt the old awning, disconnect the power if it is motorized, measure the mounting rail, order a matching unit, and bolt the new one on. But the work is high and exposed, the awning is heavy, and mistakes in measurement or installation can leave gaps or leaks. Most owners either do it themselves over a weekend or take the RV to a shop and wait a few days.
Key Takeaways
- Manual awnings take 2 to 4 hours to replace; motorized ones take longer because you must disconnect and reconnect wiring.
- You need the exact width of your RV's mounting rail and the depth you want the awning to extend — measure twice before ordering.
- Replacement awnings come in manual crank, motorized, and semi-automatic styles, and prices vary widely by brand and fabric type.
- If you are uncomfortable working at height or do not have a helper, a professional installation is worth the cost to avoid injury or damage.
What you need to know before you start
Before you order anything, you need three measurements: the width of your RV's mounting rail (the aluminum channel that runs along the side where the awning bolts), the depth you want the awning to extend when open, and the height of your RV at the mounting point. Write these down and double-check them — ordering the wrong width is the most common mistake and means sending it back.
You also need to know whether your current awning is manual (you crank it open and closed by hand), motorized (a motor does the work), or semi-automatic (a button retracts it but you open it by hand). If you are replacing a motorized one, you will need to disconnect 12-volt wiring, which adds time and requires basic electrical knowledge. If you are not comfortable with that, a shop is the safer choice.
Check your RV's manual or contact the manufacturer to confirm the mounting rail type — different RVs use different rail systems, and the awning must match. Some use Carefree's standard rail, others use Dometic, and some older RVs use proprietary systems. Ordering the wrong type means it will not bolt on.
Removing the old awning
Start by fully retracting the awning and securing it so it cannot move. If it is motorized, disconnect the 12-volt power at the battery or the breaker panel — do not just unplug it. If it is manual, make sure the crank handle is stowed and the awning is locked in the closed position.
Unbolt the mounting brackets from the RV's rail using a socket wrench or adjustable wrench. There are usually four to six bolts, one at each end and one or two in the middle. Keep these bolts in a container so you do not lose them — you may reuse them on the new awning. Once the bolts are out, the awning is held only by its own weight, so have a helper steady it while you slide it out of the rail. Do not try to do this alone; the awning is awkward and heavy, and dropping it can injure you or damage the RV.
If the awning is motorized, you will also need to disconnect the wiring harness. Take a photo of the connector before you unplug it so you know how to reconnect the new one. Some motorized awnings have a separate control switch inside the RV that you may need to remove as well.
Ordering and preparing the replacement
Once you have your measurements, contact an RV parts supplier or awning manufacturer directly. Major brands include Carefree, Dometic, A&E, and Lippert. Prices vary significantly — a basic manual awning in a standard size might cost $800 to $1,200, while a motorized one with a premium fabric can run $2,500 or more. Ask about fabric options: vinyl is cheaper and easier to clean, while acrylic lasts longer and resists fading.
When the new awning arrives, inspect it for damage before you install it. Check that all bolts, brackets, and hardware are included. If it is motorized, test the motor by connecting it to a 12-volt battery or power supply before you mount it — it is much easier to return a defective motor now than after installation.
Lay out all the hardware and read through the manufacturer's installation instructions. Most awnings come with a diagram showing which bolts go where and in what order. Having everything organized before you climb up saves time and frustration.
Installing the new awning
Position the new awning at the mounting rail and align the bolt holes. Slide it into the rail carefully — it should move smoothly without binding. Once it is positioned, insert the bolts by hand first so you can align everything before tightening. Tighten the bolts in a cross pattern (one end, then the other, then the middle) so the awning sits evenly in the rail. Do not over-tighten; you want them snug but not so tight that you strip the threads.
If the awning is motorized, reconnect the wiring harness using the photo you took earlier. Run the wire along the RV's exterior, securing it with clips so it does not hang loose or get pinched. Connect the power at the battery or breaker panel and test the motor before you close up the RV. Open and close it a few times to make sure it moves smoothly and stops at the right points.
Once everything is find and working, test the awning in different weather. Open it on a calm day and make sure it extends evenly and locks in place. Close it and check that the fabric is not twisted or bunched. If you notice any gaps between the awning and the RV, or if it does not retract fully, stop and check your installation against the instructions.
When to hire a professional instead
If your RV is tall, you are uncomfortable working at height, or you do not have a helper, a professional installation is worth the money. RV service centers have lifts or scaffolding that make the job safer, and they can spot problems (like a bent rail or damaged mounting points) that you might miss. They also handle the wiring on motorized awnings, which reduces the risk of electrical problems later.
A shop installation typically takes one to two days depending on how busy they are. Call ahead to schedule and ask whether they stock the awning you want or if you need to order it and bring it in. Some shops will install an awning you buy elsewhere, while others require you to buy from them. Expect to pay $300 to $600 in labor on top of the awning cost.
Maintenance after replacement
A new awning will last longer if you care for it. Clean the fabric twice a year with mild soap and water, and let it dry completely before retracting it — moisture trapped in the folds can cause mildew. If you live in a very sunny climate, consider a protective cover or park in shade when the RV is not in use. Check the bolts every few months and tighten any that have loosened from vibration.
If your awning is motorized, lubricate the motor and gears once a year with a light machine oil. Do not use heavy grease, which attracts dirt. Test the motor regularly to catch problems early — if it sounds strained or moves slowly, have it serviced before it fails completely.
Frequently Asked Questions
How long does it take to replace an RV awning?
A manual awning takes 2 to 4 hours if you have a helper and the right tools. A motorized awning takes 4 to 6 hours because you must disconnect and reconnect the wiring. A professional shop usually completes the job in one to two days, depending on their schedule.
Can I replace just the fabric instead of the whole awning?
Some awning frames can be recovered with new fabric, which costs $400 to $800 and takes a few days at a shop. This works if the frame is straight and the motor (if motorized) still works. If the frame is bent or the motor is dead, replacing the entire unit is usually cheaper than recovering.
What is the difference between manual, motorized, and semi-automatic awnings?
Manual awnings use a hand crank to open and close. Motorized awnings have a 12-volt motor that does both. Semi-automatic awnings have a motor that retracts them but require a hand crank to open. Motorized is most convenient but costs more and has more parts that can fail.
Do I need to disconnect the battery before I work on a motorized awning?
Yes, disconnect the negative terminal at the battery or turn off the breaker that powers the awning circuit. This prevents accidental set up while you are working and reduces the risk of electrical shock or damage to the motor.
What should I do if the new awning does not fit the mounting rail?
Stop and contact the supplier when ready. Measure the rail width again and compare it to the awning specifications. If there is a mismatch, the awning may need to be returned and replaced with the correct size. Do not force it into the rail, as this can damage both the awning and the RV.