RV doors wear out faster than house doors because they open and close constantly, seal against moving air and water, and carry their own weight on hinges that flex with the road. Replacement means choosing between a full door assembly (frame, hinges, latch, and all) or just the door panel itself, understanding what fits your RV model, and deciding whether to hire a technician or do the work yourself.

Key Takeaways

  • RV doors come as complete assemblies or panel-only replacements, and which one you need depends on whether the frame and hinges are damaged or just the door itself.
  • Your RV's make, model, and year determine what doors are available, so you will need that information before shopping or contacting a supplier.
  • Entry doors, bathroom doors, and bedroom doors have different frame sizes and latch mechanisms, so measure your opening and note the door type before ordering.
  • Installation can range from bolting on a new assembly (a few hours) to removing the old frame and sealing the new one (a full day or more), depending on damage and your skill level.
  • RV-specific suppliers and salvage yards often stock doors cheaper than dealerships, but shipping weight and lead times vary widely.

Full Assembly Versus Panel-Only Replacement

A full door assembly includes the frame, hinges, latch mechanism, weatherstripping, and the door panel itself. You order it as one unit and bolt it into the opening. This is the right choice if the frame is cracked, the hinges are bent or rusted, the latch no longer holds, or water has damaged the frame enough that it no longer seals. Full assemblies cost more but eliminate the guesswork of matching old hardware to new panels.

A panel-only replacement is just the door itself — the flat or curved piece that swings open and closed. You keep your existing frame, hinges, and latch and bolt the new panel onto the old hardware. This works when the frame and hinges are still sound but the panel is cracked, warped, or so weathered that it no longer seals. Panel-only doors cost less and install faster, but they require that your existing hardware is straight and functional.

Before you decide, inspect the frame and hinges. Push on the frame from inside and outside — it should not flex or creak. Look at the hinges for rust, bent metal, or gaps where they bolt to the frame. If the door closes and latches smoothly without binding, the hardware is likely fine and a panel replacement will work. If the door sticks, sags, or the frame shows cracks or soft spots from water damage, order a full assembly.

Identifying Your RV Door Type and Size

RV doors are not interchangeable across brands or even across different models from the same manufacturer. You need your RV's make (Winnebago, Fleetwood, Forest River, and so on), model name, and year before you contact a supplier. This information is usually on a placard inside the RV near the driver's seat or on the exterior near the hitch.

Next, identify which door you are replacing. Entry doors (the main door you walk through) are the most common replacement and come in standard widths, usually 24 to 32 inches. Bathroom doors are narrower, often 22 to 24 inches, and use a different latch. Bedroom or closet doors may slide rather than swing, or swing inward rather than outward. Measure the width and height of your door opening from the inside of the frame, and note whether the door swings in or out and which side the hinges are on.

Take a photo of the door from the outside and inside, showing the hinges, latch, and any visible damage. When you contact a supplier, they will ask for the RV year, make, and model, and they may ask you to describe the door location or send a photo to confirm you have the right part. Lead times vary — some doors ship within a week, others take four to eight weeks if they are made to order.

Where to Buy RV Doors

RV dealerships stock doors for their own brand and can order others, but prices are typically 30 to 50 percent higher than independent suppliers. They do offer the advantage of installation service on-site, which can save you time if you are not comfortable doing the work yourself.

RV-specific parts suppliers like Camping World, Lazydays, and online retailers specializing in RV components often have lower prices and faster shipping than dealerships. They maintain inventory of common doors and can usually tell you over the phone whether a door fits your model. Shipping costs are high because doors are large and heavy — expect $50 to $150 for ground shipping depending on distance.

RV salvage yards and used parts dealers are the cheapest option if you are willing to buy a used door. Quality varies widely, and you may need to inspect the door in person or rely on photos and the seller's description. Salvage doors work well if your RV is older and you are not concerned about an exact color match, or if you are replacing a door temporarily while you save for a new one.

Before ordering, confirm the return policy. Some suppliers allow returns within 30 days if the door does not fit, others do not. Ask whether the price includes weatherstripping and any hardware you will need for installation.

Tools and Materials You Will Need

If you are replacing just the panel, you need basic hand tools: a drill or screwdriver set, a wrench or socket set to fit your door's bolts, a level, and a rubber mallet. You may also need new weatherstripping if the old strips are compressed or cracked — measure the perimeter of your door opening and order weatherstripping designed for RVs, which is more flexible than house weatherstripping.

If you are replacing a full assembly, add a caulking gun and exterior RV sealant (usually silicone or polyurethane rated for RV use) to your list. You will also need a pry bar or flat screwdriver to remove the old frame without damaging the wall around it. Some installers use shims (thin wooden wedges) to level the new frame before bolting it down.

Wear safety glasses when removing the old door, especially if it is cracked or if you are prying out a frame. Have a helper on hand — RV doors are awkward to handle alone, and a full assembly with frame can weigh 50 to 80 pounds.

Steps for Replacing a Panel-Only Door

Start by opening the door fully and supporting it with a jack or block of wood under the outer edge so it does not sag while you work. Locate the bolts that attach the door panel to the hinges — usually four to six bolts, two or three per hinge. Remove these bolts with a wrench or socket, keeping them in a safe place. Carefully lift the old panel away from the frame.

Inspect the hinges and frame for rust, bent metal, or damage. If you see rust, wire-brush it away. If a hinge is bent, the door will not hang straight on the new panel — you may need to replace the hinge or order a full assembly instead. Check that the frame is level using a level tool; if it is not, you may need to shim it before hanging the new panel.

Position the new panel on the hinges, aligning the bolt holes. Insert the bolts by hand first to make sure they line up, then tighten them with a wrench. Do not over-tighten — you want the bolts snug enough that the door does not rattle, but not so tight that you crack the panel or strip the threads. Test the door by opening and closing it several times. It should swing smoothly and close without binding.

If the door does not seal tightly, check the weatherstripping. If the old strips are compressed, peel them away and install new ones, pressing them firmly into the groove around the frame. Close the door and look for light leaks around the edges — if you see gaps, adjust the strike plate (the metal piece the latch catches on) by loosening its bolts and moving it slightly until the door closes flush.

Steps for Replacing a Full Door Assembly

Remove the old door by unbolting the hinges from the frame, just as you would for a panel replacement. Then locate the bolts that attach the frame itself to the RV wall — usually six to ten bolts around the perimeter. Remove these bolts and carefully pry the old frame away from the wall. You may need to cut away old caulk or sealant with a utility knife to free the frame.

Inspect the wall opening for rot, water damage, or bent metal. If the wall is soft or discolored, you have a moisture problem that needs to be addressed before you install the new frame — water will find its way in again if the underlying damage is not fixed. If the opening is sound, clean away old caulk and debris with a scraper or wire brush.

Position the new frame in the opening and use shims to level it front-to-back and side-to-side. Check with a level on multiple sides. Once the frame is level and square, drill pilot holes through the frame bolt holes into the RV wall, then bolt the frame down. Do not fully tighten the bolts yet — leave them snug but loose enough to adjust if needed.

Hang the door on the hinges and test it for smooth operation and proper closure. Once you are satisfied, fully tighten all the frame bolts. Run a bead of exterior RV sealant around the outside perimeter where the frame meets the wall, smoothing it with a wet finger or caulk tool. Allow the sealant to cure for 24 hours before exposing the door to rain or heavy moisture.

When to Hire a Professional

If the RV wall around the door opening shows signs of water damage, rot, or soft spots, have a technician inspect it before you order a new door. Replacing the door without fixing the underlying damage will not solve the leak, and moisture will continue to damage the wall and interior.

If you are uncomfortable working at heights (for doors on the upper part of a motorhome or fifth wheel), or if you do not have a helper to support the door while you work, hiring an RV technician is worth the cost. A technician can also help you match the door color and finish to your RV if you are concerned about appearance.

Most RV service centers charge $100 to $300 per hour for labor, plus the cost of the door itself. A panel replacement typically takes two to four hours; a full assembly replacement takes four to eight hours depending on the condition of the wall and frame. Get a quote before you commit, and ask whether the price includes sealant and weatherstripping.

Frequently Asked Questions

Can I replace an RV door with a standard house door?

No. House doors are heavier, wider, and designed for stationary walls. RV doors are lighter and built to flex slightly with the RV frame as it moves. A house door will not fit the frame, and even if you forced it to fit, it would be too heavy for RV hinges and would crack the wall around the opening.

How long does a new RV door last?

A well-maintained RV door typically lasts 10 to 15 years. Lifespan depends on how often you open and close it, how well you seal it against moisture, and whether you store the RV in direct sun. Doors in hot, dry climates tend to last longer than doors in humid or rainy regions.

What if my RV model is discontinued and I cannot find a matching door?

Contact RV salvage yards that specialize in your brand, or search online forums for your RV model — other owners may know of compatible doors from similar models or years. Some aftermarket manufacturers make universal RV doors that can be adapted to fit non-standard openings, though this usually requires custom framing.

Do I need to remove the door to replace just the weatherstripping?

No. You can peel away old weatherstripping without removing the door. Clean the groove with a scraper, dry it thoroughly, and press new weatherstripping into place. This is a quick fix if your door is leaking but the panel and frame are still sound.

What is the most common reason RV doors fail?

Water damage and weatherstripping failure are the top causes. Moisture enters through gaps in the seal, soaks into the frame and wall, and causes rot and mold. Regular inspection of the weatherstripping and prompt resealing when you see gaps will extend the life of your door significantly.