RV screen doors wear out faster than you'd expect
An RV screen door takes constant use — opening and closing multiple times a day, flexing in wind, and sitting exposed to sun and moisture. The mesh tears, the frame warps, or the hinges loosen until the door won't close properly or seal against bugs. Replacing it yourself costs between $150 and $400 in parts, depending on your RV model, and takes two to four hours. A shop replacement runs $400 to $800 including labor. Most owners can handle this job with basic tools and no special skills.
The first step is identifying what you actually need to replace. Some RVs have a full screen door assembly that comes out as one unit. Others have a screen insert that slides into an existing frame. A few have a retractable screen built into the awning. Knowing which type you have determines whether you're ordering a complete door or just the mesh and frame components.
Key Takeaways
- RV screen doors come in three main types — full assembly, frame-and-mesh insert, or retractable — and you need to know which yours is before ordering parts.
- Measure your door opening width, height, and depth, and note your RV make and model, because screen doors are not one-size-fits-all.
- Removing the old door usually means unscrewing hinges or sliding the frame out of tracks, a task that takes 15 to 30 minutes with a screwdriver or hex key.
- Installing the new door is the reverse process, but you'll need to check that it closes smoothly and seals against the frame before you're done.
Identify your screen door type and get the right measurements
Walk to your RV entry door and look at how the screen attaches. If the entire screen assembly — frame, hinges, and all — bolts to the main door frame, you need a full replacement door. If the screen mesh sits in a separate frame that slides into vertical tracks on either side of the doorway, you have an insert-style door. If your awning has a motorized or manual screen that rolls down, that's a retractable screen and requires different parts.
Once you know the type, measure the opening. For a full assembly door, measure the width of the doorway, the height from threshold to top, and the depth of the frame (how far it sticks out). For an insert-style door, measure the width and height of the track opening. Write down your RV's make, model, and year — screen doors are model-specific, and a door for a 2015 Jayco may not fit a 2018 Jayco of the same floor plan.
Take a photo of your current door from the outside and inside. When you contact a supplier, they can often tell you the exact part number just from the photo and your RV information. This saves you from ordering the wrong size.
Order the replacement door or frame-and-mesh kit
RV-specific screen doors come from a handful of manufacturers. The most common sources are RV parts suppliers like Camping World, Amazon (which stocks many RV doors), eBay, and the manufacturer's own website if your RV brand makes its own doors. Some local RV shops stock common sizes and can show you the door in person before you buy.
When you order, confirm that the door comes with all hardware — hinges, screws, weatherstripping, and any springs or closers. Some kits include only the frame and mesh, and you'll need to transfer hinges from your old door. Read the product description carefully to see what's included. If you're unsure, contact the seller and ask what tools and parts you'll need to complete the installation.
Delivery usually takes three to seven days for in-stock items. If you're in a campground and need the door quickly, check whether a local RV service center stocks replacements for your model — many do, and you can pick it up the same day.
Remove the old screen door
Close the main RV entry door so you have a clear view of the screen door frame. Look for the hinges — they're usually on the right side of the door, bolted to both the screen frame and the main door frame. You'll see either Phillips-head screws or hex bolts. Have a screwdriver or hex key ready.
If your door is held in by hinges, unscrew all bolts from the hinges. Start with the top hinge, then the middle (if there is one), then the bottom. Have someone hold the door steady as you remove the last bolts, because the door will be loose and could swing or fall. Lift the door straight out and set it aside.
If your door is an insert-style frame that slides in tracks, look for a release button or clip at the top of each track. Press or slide these to unlock the frame, then lift the frame straight up and out of the tracks. Some frames need to be tilted slightly at the top to clear the track opening.
Once the old door is out, inspect the hinges or tracks for damage. If the hinges are bent or the tracks are dented, you may need to straighten them or have them replaced before the new door will fit properly. Wipe down the area where the new door will sit to remove dust and debris.
Install the new screen door
If you're installing a full assembly door with hinges, position it in the doorway and align the hinge holes with the bolt holes on the main frame. Start the top hinge bolts by hand first — don't tighten them fully yet. This lets you adjust the door's position slightly if it's not perfectly aligned. Once the top hinge is hand-tight, install the middle and bottom hinges the same way.
Now step back and look at the door. It should sit evenly in the frame with equal gaps on all sides. If one side is wider than the other, loosen the hinges slightly and shift the door until the gaps are even. Then tighten all bolts firmly with your screwdriver or hex key. Don't overtighten — you want the door snug but not so tight that the frame bends.
If you're installing an insert-style door, slide the frame into the tracks from the top, making sure both sides go in evenly. Lower the frame until it sits fully in the tracks, then engage any release buttons or clips to lock it in place. The frame should slide smoothly and not bind or stick.
Test the door and seal any gaps
Open and close the door several times. It should swing smoothly without sticking, and it should close with a gentle push — not so loose that it swings open on its own, and not so tight that you have to force it. If it binds or sticks, the hinges may not be aligned. Loosen them slightly, adjust the door position, and retighten.
Check the weatherstripping around the frame. This is the foam or rubber seal that keeps bugs and drafts out. If it's compressed, torn, or missing, the door won't seal properly. Most replacement doors come with new weatherstripping already installed, but if yours didn't, you can buy adhesive-backed weatherstripping tape at any hardware store and explore it to the frame edges.
Close the door and look for light coming through the edges. If you see gaps, the door may not be closing all the way. Check that nothing is blocking the frame, and make sure the hinges are tight. If the door still won't close fully, the frame may be warped — contact the supplier to see if they can send a replacement or if you need to adjust the hinges further.
Common problems and how to fix them
If the door won't close all the way, the hinges are usually the culprit. Loosen them, close the door gently, and retighten. This lets the door settle into its natural position. If it still won't close, check whether the threshold (the bottom edge of the doorway) is level. An unlevel threshold can prevent the door from closing. You may need to shim the hinges with thin metal or plastic shims to compensate.
If the door swings open on its own, the hinges are too loose or the door is hanging unevenly. Tighten the hinges and check that the gaps are even on all sides. Some RV doors come with a spring closer that holds them shut — if yours is missing or broken, you can buy a replacement closer at a hardware store and install it between the frame and the door.
If bugs are still getting in, the weatherstripping is the issue. Replace it with new adhesive-backed foam tape, pressing it firmly into place. Make sure there are no gaps where the frame meets the main door — if there are, seal them with caulk or additional weatherstripping.
Frequently Asked Questions
Can I just replace the mesh without replacing the whole frame?
Yes, if the frame is still straight and the hinges work. You can buy mesh-only kits that include new mesh and spline (the cord that holds the mesh in). You'll need a spline roller tool to press the new mesh into the frame, which costs about $10. This works well if the frame is solid but the mesh is torn.
What if my RV model is discontinued and I can't find a matching door?
Contact RV parts suppliers and ask if they have a universal or adjustable screen door that fits your opening size. Some manufacturers make doors with adjustable frames that can fit a range of widths and heights. You may also find used doors from salvage yards or online RV forums where owners sell parts.
Do I need to remove the main entry door to install a screen door?
No. The screen door bolts to the outside of the main door frame, so you only need to open the main door to access the hinges. You don't need to remove it unless the hinges are damaged and need replacement.
How long does a replacement screen door usually last?
Most RV screen doors last five to ten years depending on how much you use them and how much sun and weather exposure they get. Mesh typically tears or degrades first, followed by frame warping or hinge wear. Regular cleaning and keeping the door out of direct sun when parked can extend its life.
Is it cheaper to replace just the mesh or the whole door?
Mesh-only replacement costs $30 to $80 plus your labor. A full door replacement costs $150 to $400. If the frame is straight and hinges work, mesh replacement is cheaper. If the frame is bent, warped, or the hinges are loose, a full replacement is usually the better choice because a damaged frame won't seal properly even with new mesh.