What a track loader is and what it does
A track loader is a heavy machine used to move earth, gravel, sand, and other loose materials on construction sites, farms, and landscaping jobs. Instead of wheels, it runs on two continuous metal tracks—like a tank—that spread its weight over a wider area. This design lets it work on soft ground, mud, and uneven terrain without sinking or getting stuck the way a wheeled loader would.
The machine has a bucket or scoop at the front that lifts and dumps material into trucks or piles. The operator sits in a cab and uses hydraulic controls to raise and lower the bucket, tilt it, and steer the tracks left or right. Because the tracks grip loose ground better than tires, track loaders can work in conditions where wheeled equipment would fail—which is why you see them on muddy job sites and in quarries.
Track loaders come in different sizes, from small machines that weigh a few tons to large ones that weigh 20 tons or more. Smaller models are sometimes called skid steers with tracks, while larger ones are called track loaders or compact track loaders. The size determines how much material it can move and how much ground pressure it puts on the soil.
Key Takeaways
- Track loaders use continuous metal tracks instead of wheels, which lets them work on soft, muddy, or uneven ground without sinking.
- The hydraulic system that powers the bucket and controls steering is the most complex part and needs regular fluid checks and filter changes to avoid costly damage.
- Track tension must be checked and adjusted regularly because loose tracks slip and wear fast, while over-tight tracks overheat and break.
- Undercarriage parts—the tracks, rollers, and sprockets—wear faster than engine parts because they take the direct impact of rough ground.
- Preventive maintenance on a track loader costs far less than replacing a track or repairing a hydraulic leak that has damaged other systems.
The hydraulic system: the heart of a track loader
Nearly everything a track loader does—lifting the bucket, tilting it, steering the tracks, and lowering the boom—runs on hydraulic fluid pushed through hoses and cylinders by a pump. This system is powerful and precise, but it is also the most expensive part to repair if something goes wrong. A single hydraulic hose rupture can spray fluid everywhere, damage the engine, and leave you unable to operate the machine.
The hydraulic fluid does three things: it transmits power, it cools the system, and it lubricates the pump and cylinders. Over time, the fluid breaks down from heat and contamination. Dirt, water, and metal particles get into the system through worn seals, damaged hoses, and the breather cap on the reservoir. Once contamination builds up, it clogs filters, scratches pump surfaces, and causes leaks that spread across the engine and undercarriage.
Checking the hydraulic fluid level and condition is one of the easiest preventive steps. Most track loaders have a sight glass on the side of the reservoir so you can see the level without opening it. The fluid should be clear or amber; if it looks dark, milky, or smells burnt, it needs to be changed. Hydraulic filters should be replaced according to the manufacturer's schedule—usually every 250 to 500 hours of operation—because a clogged filter forces the pump to work harder and can cause it to fail suddenly.
Track tension and undercarriage wear
The undercarriage is the assembly of tracks, rollers, sprockets, and idlers that lets the machine move. Unlike an engine that can run for thousands of hours, undercarriage parts wear out much faster because they are in direct contact with rough ground, rocks, and abrasive material. A track that is too loose will slip and wear unevenly; a track that is too tight will overheat, stretch, and break.
Track tension should be checked every 50 to 100 hours of operation, depending on how rough the terrain is. To check it, you lift the machine slightly off the ground and measure how much the track sags in the middle. Most manufacturers specify a sag of 1 to 2 inches; if it is more, the track is too loose and needs tightening. If it is less, the track may be over-tensioned and at risk of breaking. Adjusting tension involves loosening bolts on the idler wheel and moving it forward or backward—a job that takes an hour or two but saves you from a track failure that could cost thousands.
The tracks themselves are made of steel links held together by pins and bushings. These wear out as the machine moves, and eventually the track will need to be replaced. A new track can cost $2,000 to $5,000 depending on the machine size, so keeping tension correct and avoiding unnecessary spinning or skidding extends track life significantly. Rollers and sprockets also wear as the track moves over them; if a roller seizes or a sprocket tooth breaks, the track can derail or jam.
Engine and cooling system maintenance
Track loaders are usually powered by diesel engines that work hard in dusty, hot conditions. The engine breathes through an air filter that collects dust and debris; a clogged air filter makes the engine work harder, burns more fuel, and can damage the turbocharger. Air filters should be inspected every 50 hours and replaced when they look dark or clogged—not on a fixed schedule, because job site conditions vary.
The cooling system keeps the engine and hydraulic fluid from overheating. On a track loader, the radiator and cooler are often mounted on the back or side where they collect dust and chaff from the material being moved. If the radiator fins get clogged, the engine temperature rises, the hydraulic fluid gets too hot, and both systems can fail. Cleaning the radiator with compressed air or a soft brush every week during heavy use prevents this. The coolant itself should be checked monthly and changed according to the manufacturer's schedule, usually every two years or 2,000 hours.
Fuel system and engine oil
Diesel fuel can absorb water from humid air, especially if the machine sits idle for weeks. Water in the fuel tank causes rust inside the tank, clogs the fuel filter, and can damage the fuel injectors. To prevent this, keep the fuel tank as full as possible when the machine is not in use—a full tank leaves less room for air and moisture. The fuel filter should be drained and replaced regularly; many operators drain the water trap at the bottom of the fuel filter weekly during the wet season.
Engine oil lubricates the engine and carries away dirt and heat. On a track loader, the engine works in dusty conditions and often at high throttle, so the oil gets dirty faster than it would in a car. Check the oil level every day before starting, and change the oil and filter according to the manufacturer's schedule—usually every 250 to 500 hours. Using the correct oil grade for the climate matters; thicker oil in cold weather and thinner oil in hot weather keeps the engine protected.
Electrical system and battery
Track loaders have electrical systems that start the engine, power lights and controls, and run the hydraulic pump motor on some models. The battery is exposed to vibration, heat, and dust, so it corrodes faster than a car battery. Check the battery terminals monthly and clean off any white or blue corrosion with a wire brush and baking soda solution. A corroded terminal can prevent the engine from starting even if the battery is charged.
The alternator charges the battery while the engine runs. If the alternator fails, the battery will drain and the machine will not start. Most alternators last several years, but if the machine sits idle for long periods, the battery can discharge and damage the alternator. Connecting a battery maintainer (a low-current charger) during storage prevents this. The starter motor also wears out over time; if the engine cranks slowly or does not start, the starter may be failing and should be tested before it leaves you stranded.
Seasonal storage and winterization
If a track loader sits unused for months, several things can go wrong. Fuel can separate and gum up the injectors. Hydraulic fluid can absorb moisture and corrode internal parts. The battery can discharge completely. Seals can dry out and crack. To prepare a machine for storage, run the engine at full throttle for 15 minutes to warm the hydraulic fluid, then shut it down and let it cool. Drain the fuel tank or add a fuel stabilizer to prevent gum formation. Top off the hydraulic reservoir so there is less air space for moisture to condense into. Disconnect the battery or connect a maintainer to keep it charged.
In cold climates, diesel fuel can gel and block fuel lines. Use winter-grade diesel or add a fuel additive that lowers the pour point. Check the coolant concentration to make sure it will not freeze. If the machine will sit outside, cover it to keep rain and snow off the engine and hydraulic lines. Before starting it again after storage, check all fluid levels, inspect hoses for cracks, and run it at low throttle for a few minutes before putting it to work.
Frequently Asked Questions
How often should I grease a track loader?
Most track loaders have grease fittings on the idler wheels, rollers, and pivot points. These should be greased every 50 to 100 hours of operation, or weekly during heavy use. Use the grade of grease specified in the manual—usually a lithium or calcium-based grease. Over-greasing can force grease into seals and damage them, so pump grease until it just starts to come out of the seal, then stop.
What does it mean if the hydraulic fluid is leaking?
A small drip under the machine is normal, but a steady leak means a seal or hose is failing. Hydraulic fluid is expensive and leaks can damage the engine, so find and fix the source quickly. Common leak points are hose connections, cylinder rod seals, and the pump shaft seal. A mechanic can pressure-test the system to locate the leak.
Can I use regular motor oil in a track loader engine?
No. Track loaders use diesel engines that require diesel-specific oil, usually 15W-40 or 10W-30 depending on climate. Diesel oil has different detergent packages and viscosity than gasoline engine oil. Using the wrong oil can damage the engine and void the warranty. Always check the manual for the correct grade.
How do I know if the track is about to break?
Listen for unusual noises—clanking, grinding, or a rhythmic clicking as the track moves. Look for bent or missing links, cracks in the track, or a track that sits lower on one side than the other. If a link breaks, the track will derail. If you see damage, stop using the machine and have the track inspected by a mechanic before it fails completely.
What is the best way to store a track loader long-term?
Park it on level ground, not on soft soil where it can sink. Drain the fuel or add stabilizer. Top off all fluids. Disconnect the battery or connect a maintainer. Cover the machine to keep rain and UV light off the paint and seals. Check it monthly to make sure nothing has leaked or corroded. Before using it again, check all fluid levels and run it at low throttle for several minutes.