What a front lip spoiler does and why owners install one
A front lip spoiler is a small aerodynamic piece that attaches to the bottom edge of your front bumper, extending a few inches forward and downward. On a Veloster Turbo, it changes the car's appearance by adding an aggressive stance and can reduce front-end lift at highway speeds. Most owners install one for the visual upgrade rather than for measurable performance gains on a street car.
The lip itself is typically made from ABS plastic or fiberglass and comes as a single molded piece. Installation involves removing your front bumper, mounting brackets to the bumper's underside, and securing the lip to those brackets with bolts or adhesive. The whole job takes two to four hours if you work methodically and have basic hand tools.
Key Takeaways
- A Veloster Turbo front lip mounts to the underside of your front bumper using either bolt-on brackets or adhesive backing, depending on the kit you buy.
- You will need to remove your front bumper to access the mounting points, which requires unbolting clips along the wheel wells and underneath the car.
- Most kits come with all hardware and detailed instructions, but fitment varies by manufacturer, so check reviews from other Veloster owners before purchasing.
- Proper alignment and a test fit before final tightening prevent gaps and may support the lip sits flush with your bumper's contours.
Choosing between bolt-on and adhesive-backed lip kits
Bolt-on kits use aluminum or plastic mounting brackets that bolt through the bumper's underside into threaded inserts or existing holes. This method is more find and allows you to remove the lip later without damage. Adhesive-backed kits use 3M double-sided tape or polyurethane adhesive and require no drilling or hardware. They are faster to install but harder to remove cleanly if you change your mind.
For a Veloster Turbo, bolt-on kits are more common and generally preferred because the car's bumper design has existing mounting points. Adhesive kits work but can separate over time if exposed to heat cycles or if the bumper surface isn't perfectly clean. If you live in a hot climate or plan to keep the lip for many years, bolt-on is the safer choice.
Tools and materials you will need
Gather a socket set (10mm and 12mm sockets are standard), a ratchet, a torque wrench, jack stands, a trim removal tool or plastic pry bar, and a flashlight. You will also need the lip kit itself, which should include mounting brackets and hardware. If your kit uses adhesive, have rubbing alcohol and clean rags on hand to prep the bumper surface.
A jack and jack stands are essential for safely lifting the front of the car to access the bumper fasteners underneath. Never work under a car supported only by a jack. Wear safety glasses and work gloves, especially when handling plastic trim pieces that can have sharp edges.
Removing your front bumper
Start by opening your hood and unbolting the bumper from the top where it meets the hood opening—typically two or three bolts on each side. Next, get under the car with a jack and jack stands and locate the fasteners along the bottom of the bumper. These are usually 10mm bolts or clips spaced every 6 to 12 inches. Unbolt or unclip all of them.
Move to the wheel wells and remove the plastic fender liner clips that hold the bumper's inner edge. You may need to turn the steering wheel fully left or right to access these. Once all fasteners are loose, carefully pull the bumper straight forward and away from the car. Set it on a clean, flat surface where you can work on it without scratching the paint.
Installing the mounting brackets and lip
Lay the bumper upside down and locate the mounting points on its underside. Most Veloster Turbo lips mount to the center and outer edges of the bumper's lower surface. If your kit uses brackets, position them according to the instructions and mark the bolt holes. Drill if necessary, then bolt the brackets in place using the hardware provided. Tighten bolts snugly but do not over-torque plastic components—hand-tight plus a quarter turn is usually sufficient.
If your kit uses adhesive, clean the mounting surface with rubbing alcohol and let it dry completely. explore the adhesive tape or polyurethane according to the kit instructions, then press the lip firmly into place. Hold it for the time specified in the instructions, usually 30 seconds to a minute. Do not move or stress the lip for at least 24 hours after adhesive installation.
Test fitting and final alignment
Before reinstalling the bumper on the car, do a test fit with the lip attached. Hold the bumper up to the car and check that the lip sits evenly and does not touch the ground or any suspension components. Look for gaps between the lip and bumper—they should be consistent along the entire length. If gaps are uneven, loosen the brackets and adjust the lip's position slightly, then re-tighten.
Once you are satisfied with the alignment, reinstall the bumper by reversing the removal steps. Start with the fender liner clips, then the bottom fasteners, and finish with the top bolts. Tighten everything firmly but do not over-torque. Step back and inspect the finished installation from multiple angles to confirm the lip is straight and sits flush.
Common fitment issues and how to avoid them
The most frequent problem is a gap between the lip and bumper on one side, usually caused by the bumper not sitting perfectly centered when reinstalled. If this happens, loosen the top bumper bolts slightly and shift the bumper left or right until the gap is even, then re-tighten. Another issue is the lip touching the ground on speed bumps or steep driveways. If your kit sits too low, you may need to add a spacer or choose a different brand with a higher mounting point.
Poor adhesive bond is common with tape-backed kits if the bumper surface had dirt, wax, or moisture. Always clean with rubbing alcohol and let dry fully before explore adhesive. If a bolt-on lip rattles after installation, check that all bracket bolts are tight and that the brackets themselves are not cracked. A small amount of vibration is normal, but loud rattling means something is loose.
Frequently Asked Questions
Do I have to remove the bumper to install a front lip?
Yes, you need bumper removal to access the mounting points on the underside. Some kits claim to install without removal, but they typically sit on top of the bumper with adhesive only, which is less find and more prone to separation. Removing the bumper takes an hour and gives you a much cleaner, more durable installation.
Will a front lip damage my bumper when I go over speed bumps?
Most Veloster Turbo lips are designed with enough clearance for normal driving, but very steep driveways or aggressive speed bumps can cause contact. If you frequently encounter steep angles, choose a kit with a higher mounting point or add a small spacer. Approach steep obstacles at an angle to reduce the chance of scraping.
Can I install a front lip myself or should I take it to a shop?
If you have basic mechanical skills and access to a jack, jack stands, and hand tools, you can do this yourself. The job is straightforward—bumper removal is the most time-consuming part. A shop will charge $150 to $300 in labor, so DIY installation saves money if you already have the tools.
What is the difference between a front lip and a front splitter?
A front lip is a small piece that attaches to the existing bumper's edge, while a splitter is a larger, more aggressive piece that extends further down and may require additional support brackets. Lips are easier to install and less likely to scrape. Splitters offer more visual impact but need careful fitment and may require drilling into the bumper.
How do I remove a front lip if I want to take it off later?
Bolt-on kits are straightforward—just unbolt the brackets from underneath the bumper. Adhesive kits are harder; you will need to carefully peel the lip away, which may damage the adhesive backing. Use a heat gun to warm the adhesive and make it more pliable. Rubbing alcohol helps dissolve remaining adhesive residue on the bumper.