Connect the red cable to the positive terminal first, then the black cable to the negative terminal
The correct order matters because it reduces the risk of sparks near the battery. On the dead battery, attach the red clamp to the positive (+) terminal — it's usually larger and marked with a plus sign. Then attach the black clamp to the negative (−) terminal on the same dead battery. Next, connect the red clamp to the positive terminal on the working battery, and finally connect the black clamp to an unpainted metal surface on the engine block or frame of the dead car — not the negative terminal. This last step grounds the circuit and keeps sparks away from battery gases.
Reversing the order or connecting both clamps to the same battery first creates a short circuit and can damage both vehicles' electrical systems. The sequence protects your car's computer, alternator, and other electronics.
Key Takeaways
- Always connect red to positive (+) on the dead battery first, then black to negative (−) on the dead battery.
- The final connection is red to positive on the working battery, then black to a bare metal engine surface on the dead car — not to its negative terminal.
- Connecting in the wrong order can short-circuit both vehicles and damage their electrical systems.
- Make sure both batteries are the same voltage (usually 12 volts) before connecting.
- Remove the clamps in reverse order: black from the dead car, black from the working car, red from the working car, red from the dead car.
Why the positive terminal comes first
Starting with the positive terminal on the dead battery establishes the main power path before you complete the circuit. If you connected negative first, any accidental contact between the red clamp and metal on the dead car would create a spark at that point instead of at the battery terminals, where the risk is lower.
The positive terminal is almost always the larger of the two and has a plus sign (+) printed or embossed on the battery case or terminal cover. If the terminals are the same size, look for the red plastic cover or the wire leading to the starter — that's your positive side.
Why the final connection is to bare metal, not the negative terminal
Connecting the last black clamp directly to the negative terminal on the dead battery creates a complete circuit with both clamps at the battery. Any spark that occurs during this final connection happens right at the battery, where hydrogen gas can accumulate. Grounding to the engine block or frame instead moves the spark away from that gas.
Look for an unpainted bolt, bracket, or flat metal surface on the engine block itself — not plastic, not rubber, and not any component that looks like it might contain fluid. A bolt on the engine block, the alternator mounting bracket, or the battery hold-down bracket all work. Avoid battery terminals, the starter, or anything near the fuel system.
Checking battery voltage before you connect
Most vehicles use 12-volt batteries, but some older trucks and specialty vehicles use 6-volt or 24-volt systems. Connecting a 12-volt charger to a 6-volt battery can damage it permanently. Check your owner's manual or look at the battery itself — the voltage is printed on the case.
If you're jumping a vehicle you don't own or aren't familiar with, ask the owner or look under the hood before you touch anything. A quick question takes seconds and prevents expensive damage.
Removing the cables in the right order
Disconnection order is the reverse of connection. Remove the black clamp from the engine block or frame of the dead car first. Then remove the black clamp from the working car. Next, remove the red clamp from the working car. Finally, remove the red clamp from the dead car.
This reverse sequence prevents sparks and ensures the circuit closes safely. Wait at least a minute after the working car's engine starts before you remove any clamps — this gives the alternator time to stabilize the electrical system.
What to do if the terminals are corroded or covered
Battery terminals sometimes have plastic covers or are crusted with white, blue, or green corrosion. Lift or remove any plastic cover first — it's usually held by friction and pulls straight up. If corrosion is heavy, use a wire brush or an old toothbrush to scrub the terminal until bare metal shows through.
Corrosion doesn't prevent a jump start, but it reduces electrical contact. A quick scrub takes 30 seconds and makes the connection more reliable. If the terminal is so corroded that you can't see metal underneath after brushing, that battery may need replacement soon.
Safety steps before you connect anything
Turn off both vehicles completely before you attach any cables. Check that the working car's battery is in good condition — if it's cracked, leaking, or visibly damaged, do not use it to jump another car. Make sure both vehicles are parked on level ground and that no one is touching either car.
Wear eye protection if you have it. Battery acid can splash during a jump start, though it's rare. Keep the cables away from moving engine parts — belts and fans can catch them once the engine starts.
Frequently Asked Questions
Can I connect both red clamps to the positive terminals and skip the black clamp to metal?
No. Connecting both black clamps to the negative terminals creates a complete circuit at the battery, where hydrogen gas can collect. Grounding the final clamp to engine metal moves any spark away from that gas. This is a safety requirement, not a preference.
What if I connect the clamps in the wrong order?
If you connect black before red, or if you reverse the polarity (red to negative, black to positive), you risk sparks and electrical damage to both vehicles. Stop when ready, remove all clamps, and start over. Do not start either engine.
How long should I wait after connecting before I start the engine?
You can start the working car's engine right away. Let it run for 2 to 3 minutes before you try to start the dead car. This gives the working battery time to transfer charge and stabilize the voltage.
Do I need to remove the battery terminals before jumping?
No. You connect the clamps directly to the terminals while they're still on the battery. Removing terminals is unnecessary and creates extra work.
What if the battery is in a weird location and I can't reach the terminals?
Some vehicles have batteries under the rear seat or in the trunk. Your owner's manual shows the location and usually has a diagram of the terminals. If you still can't reach them, a professional jump service or tow truck can help.