The 2013 Cruze uses a cartridge-style oil filter mounted on top of the engine
The 2013 Chevrolet Cruze does not have a spin-on oil filter like many other vehicles. Instead, it uses a cartridge-style filter that sits in a plastic housing on top of the engine, near the front passenger side. The filter element itself is a cylindrical cartridge that you remove and replace from above — you do not need to get under the car to access it, which makes the job simpler than on many other models.
The filter housing is a white or translucent plastic cap with a large center bolt. When you unscrew that bolt, the entire housing comes off and the filter cartridge slides out. This design means you will need a filter wrench sized for the housing cap, not a traditional spin-on filter wrench.
Key Takeaways
- The 2013 Cruze filter is a cartridge type in a plastic housing on top of the engine, accessed from above without lifting the car.
- You will need a cartridge filter wrench (typically 74 mm or 86 mm, depending on engine size) to remove the housing cap.
- Replacement cartridges cost between $8 and $15, and the housing cap gasket should be replaced each time you change the filter.
- The job takes 10 to 15 minutes and requires no special tools beyond the filter wrench and a drain pan for old oil.
- Always check your owner's manual or the filter box to confirm the correct part number, as the 1.6L and 1.8L engines use different filter sizes.
Filter size and part numbers for each engine option
The 2013 Cruze came with two engine choices: a 1.6L turbo diesel and a 1.8L gasoline engine. Each uses a different filter cartridge size, so you must know which engine your car has before ordering a replacement.
The 1.8L gasoline engine uses a smaller cartridge filter, while the 1.6L diesel uses a larger one. Chevrolet part numbers are specific to each, and cross-brand equivalents from Mobil 1, Fram, and Bosch also differ by engine. The easiest way to confirm which you need is to look at your current filter housing or check your owner's manual. When you buy a replacement cartridge, the box will specify which engine it fits.
Tools and materials you will need
You will need a cartridge filter wrench to unscrew the housing cap. These are available at any auto parts store for $10 to $20 and fit over the cap like a socket. The wrench size depends on your engine — measure the diameter of your housing cap or call the parts store with your VIN and they will tell you which size to buy.
You will also need a drain pan (any shallow container works), a new filter cartridge, and a new rubber gasket for the housing cap. Most replacement filter kits include the gasket, but if you buy the cartridge alone, purchase the gasket separately — it costs $2 to $4 and prevents oil leaks. Have a rag or paper towels on hand because some oil will drip when you remove the housing.
Step-by-step replacement process
Start with the engine cold and the car parked on level ground. Open the hood and locate the white plastic filter housing on top of the engine. Place your drain pan underneath it to catch any spilled oil.
Use your cartridge filter wrench to turn the housing cap counterclockwise. It will loosen like a large bolt. Once hand-tight, unscrew it the rest of the way by hand and set it aside. The old filter cartridge will come out with the cap or remain in the housing — either way, lift it out and dispose of it. Wipe the inside of the housing clean with a rag to remove any debris or old gasket material.
Slide the new filter cartridge into the housing, making sure it sits flat on the bottom. Place the new rubber gasket on the housing cap, then screw the cap back in by hand first to avoid cross-threading. Once hand-tight, use your filter wrench to tighten it snugly — do not over-tighten, as the plastic housing can crack. A firm hand-tight turn with the wrench is enough.
Start the engine and let it idle for 30 seconds, then turn it off and wait two minutes. Check the housing cap and the area around it for leaks. If you see oil seeping, the gasket may not be seated correctly — remove the cap, reseat the gasket, and try again.
Common mistakes to avoid
The most frequent error is over-tightening the housing cap. The plastic threads can strip or crack if you use too much force. Tighten until snug, then stop — you should not need a wrench to loosen it next time. If you do, you tightened it too much.
Another mistake is forgetting to replace the rubber gasket. Reusing the old gasket often leads to slow leaks that show up a few days after the oil change. The gasket is inexpensive and should always be new. Finally, some owners forget to check that the new cartridge is seated all the way at the bottom of the housing before screwing the cap back on. If the cartridge is not fully seated, the cap will not close properly and oil will leak.
When to change your oil filter
Chevrolet recommends changing the oil filter every time you change the engine oil. For the 2013 Cruze, that interval is typically 3,000 to 7,500 miles depending on driving conditions and whether you use synthetic oil — check your owner's manual for the exact interval for your car. If you drive mostly in stop-and-go city traffic, short trips, or towing, use the shorter interval. If you drive mostly highway miles at steady speeds, you can go longer between changes.
Some owners change the filter more often than the oil as a precaution, but that is unnecessary and wasteful. The filter and oil should be changed together.
Where to buy replacement filters
Replacement cartridge filters for the 2013 Cruze are stocked at any major auto parts chain — AutoZone, O'Reilly, NAPA, and Advance Auto Parts all carry them. Prices typically range from $8 to $15 for the cartridge alone, or $12 to $20 for a kit that includes the gasket. You can also order online from Amazon or the manufacturer's website, though you will need to wait for shipping.
If you want an OEM Chevrolet filter, those are available through a Chevy dealer or online retailers that stock GM parts. OEM filters cost slightly more but are may provide to fit. Aftermarket brands like Mobil 1, Fram, and Bosch are equally reliable and usually cheaper.
Frequently Asked Questions
Can I change the filter without changing the oil?
Technically yes, but it is not recommended. The filter and oil work together — old oil contaminates a new filter, and a new filter in old oil does not clean as effectively. Change them together on the schedule in your owner's manual.
What should I do with the old filter?
Take it to an auto parts store or recycling center. Many stores that sell filters will take old ones for free. Do not throw it in the trash — the oil inside is hazardous waste in most places.
How tight should the housing cap be?
Snug is enough — tighten it until you feel resistance, then give it one more firm turn with the wrench. If you have to use all your strength, it is too tight. You should be able to loosen it by hand next time.
Is the cartridge filter more expensive than a spin-on filter?
No, cartridge filters for the Cruze cost about the same as spin-on filters for other cars — usually $8 to $15. The main difference is the tool you need to remove it, not the price of the filter itself.
What if oil leaks after I install the new filter?
Stop driving and check the housing cap when ready. The gasket is likely not seated correctly or the cap is not tight enough. Remove the cap, inspect the gasket for damage, replace it if needed, and reinstall the cap. If leaking continues, the housing itself may be cracked and need replacement.