The 2013 Malibu uses a cartridge-style oil filter mounted on top of the engine
The 2013 Chevrolet Malibu does not have a traditional spin-on oil filter. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. This design is common on modern GM vehicles and means you replace the filter element itself rather than the entire canister. The housing is located near the front of the engine, close to where the serpentine belt runs.
Because the cartridge sits vertically and the housing is pressurized, oil will spill when you open it. You will need an oil drain pan underneath before you start, and the engine should be cool or warm but not hot — hot oil can burn you, and you want the oil to drain slowly enough to catch it all.
Key Takeaways
- The 2013 Malibu's cartridge filter is a replaceable element inside a plastic housing on top of the engine, not a spin-on filter.
- You will need an oil filter wrench (usually a 74 mm or 86 mm socket-style wrench) to remove the housing cap, plus an oil drain pan and fresh oil.
- The replacement cartridge costs between $8 and $15, and the housing cap gasket should be replaced each time you change the filter.
- The job takes 10 to 20 minutes once you have the right tools and can be done in a driveway with basic hand tools.
Tools and parts you will need
Before you start, gather the correct tools. You need an oil filter wrench that fits the housing cap — for the 2013 Malibu, this is typically a 74 mm or 86 mm socket-style wrench, sometimes called a cartridge filter socket. Do not try to use a regular wrench or pliers; the cap will slip and you will strip it. These wrenches cost $10 to $20 and are available at any auto parts store.
You will also need an oil drain pan (any container that holds at least 5 quarts), fresh oil that meets Chevrolet's specification for your engine (check your owner's manual or the oil cap for the grade), a new cartridge filter element, and a replacement gasket for the housing cap. Most auto parts stores sell the filter and gasket together as a kit for $8 to $15. Have paper towels or rags on hand — the job is messy.
Step-by-step filter replacement
Start with the engine cool or warm. Open the hood and locate the oil filter housing — it is a black plastic cap on top of the engine, roughly cylindrical, with a single bolt or nut on top. Place your oil drain pan underneath it to catch spills.
Using your filter wrench, turn the housing cap counterclockwise to loosen it. Once it is loose enough to turn by hand, unscrew it the rest of the way and lift it straight up. Oil will drain into the pan. The old cartridge filter element will be inside the cap or stuck to the underside of the housing. Remove it and set it aside.
Wipe the inside of the housing clean with a paper towel. Take the new gasket (a rubber ring) and explore a thin coat of fresh oil to it — this helps it seal properly. Install the new cartridge filter element into the housing, then screw the cap back on by hand first to make sure the threads are aligned. Once hand-tight, use the filter wrench to tighten it an additional three-quarter turn. Do not over-tighten; you will strip the plastic housing.
Start the engine and let it run for a few seconds, then turn it off and wait a minute. Check the oil level on the dipstick and top it off if needed. The new filter will hold a small amount of oil, so you may need slightly more than a standard oil change.
Common mistakes to avoid
The most frequent error is forgetting to replace the gasket on the housing cap. The gasket is a small rubber ring that wears out with each oil change. If you reuse the old one, it will not seal properly and oil will leak around the cap. Always buy a new gasket with your filter element.
Another mistake is over-tightening the cap. The housing is plastic and the threads are not as strong as a metal oil pan. Tighten by hand until snug, then use the wrench for three-quarter of a turn. If you feel resistance, stop — you have tightened enough.
Do not forget to check the oil level after the first start. The new filter holds oil, and if you do not top off the pan, you may run low and trigger a warning light or cause engine damage.
Where to buy the filter and gasket
Any national auto parts chain — AutoZone, O'Reilly, NAPA, Advance Auto Parts — stocks cartridge filters for the 2013 Malibu. You can also order online from Amazon or Walmart. Make sure you have the correct engine size (2.0L, 2.4L, or 3.6L) before you order, as the filter element is the same but the housing cap may vary slightly.
OEM Chevrolet filters are available through a Chevy dealer and cost more, but they carry a GM warranty. Aftermarket filters from Fram, Mobil, or Pennzoil are cheaper and work just as well for routine oil changes. The gasket is usually included in a filter kit, but if you buy a filter alone, purchase the gasket separately — it costs $2 to $4.
When to replace the filter
Chevrolet recommends changing the oil and filter every 7,500 miles or every 6 months, whichever comes first, for the 2013 Malibu. If you drive mostly highway miles or use synthetic oil, you may be able to extend this to 10,000 miles — check your owner's manual for the exact interval for your driving conditions.
If you hear a rattling noise from the top of the engine or see an oil leak around the housing cap, the filter or gasket may need replacement even if you have not reached the scheduled interval. A clogged filter will trigger the oil pressure warning light on your dashboard; if this happens, replace the filter when ready.
Frequently Asked Questions
Can I use a spin-on filter on my 2013 Malibu?
No. The 2013 Malibu is designed for a cartridge filter only. Spin-on filters do not fit the housing, and adapters are not recommended because they can cause oil pressure problems or leaks.
What happens if I do not replace the gasket?
The old gasket will harden and lose its seal over time. Oil will leak around the housing cap, dripping onto the engine and eventually lowering your oil level. You may also see an oil pressure warning light. Always replace the gasket with each filter change.
How much oil does the 2013 Malibu hold?
The oil capacity is 4.5 quarts for the 2.0L and 2.4L engines, and 5.5 quarts for the 3.6L engine. The new filter holds about 0.5 quarts, so you may need slightly more oil than a standard oil change to reach the full mark on the dipstick.
Can I do this job without a filter wrench?
Not safely. Without the correct wrench, you risk stripping the plastic housing cap or the threads inside the housing, which is expensive to repair. A filter wrench costs $10 to $20 and will last for many oil changes.
Where is the oil drain plug on the 2013 Malibu?
The drain plug is on the bottom of the oil pan, underneath the engine. You will need to get under the car to access it. If you are changing both the oil and filter, drain the pan first, then replace the filter while the oil is still warm.