The 2013 Ford Focus uses a cartridge-style oil filter mounted on top of the engine
The 2013 Ford Focus does not have a spin-on oil filter like many other vehicles. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. The housing is white or translucent plastic, roughly the size of a soda can, and you'll find it near the front of the engine bay, close to the valve cover.
This design means you cannot straightforward unscrew a filter canister. You'll need to remove the housing cap, pull out the old filter element, and install a new one. The process takes about 10 to 15 minutes once you have the right parts and tools, and it costs less than a spin-on filter replacement at most shops.
Key Takeaways
- The 2013 Ford Focus cartridge filter sits in a plastic housing on top of the engine, not underneath or on the side like older designs.
- You will need a cartridge filter element (not a spin-on), an oil filter wrench or socket to remove the housing cap, and a new rubber O-ring seal.
- The housing cap typically requires a 74 mm or 86 mm socket depending on engine size — using the wrong size can strip the plastic threads.
- Always replace the rubber O-ring that seals the housing cap, because reusing the old one often causes slow oil leaks after the service.
What filter size and part number your Focus needs
The 2013 Ford Focus came with two engine options in North America: the 2.0-liter EcoBoost and the 2.0-liter naturally aspirated engine. Both use the same cartridge filter housing, but you need to confirm which engine you have before ordering parts.
The OEM (original equipment manufacturer) Ford part number is CM-5Z-6744-A for the cartridge filter element. Aftermarket equivalents include Motorcraft FL-400-HE, Fram CH9656, and Bosch 3330. The O-ring seal is part number CM-5Z-6714-A. If you buy a filter kit, it usually includes the element and O-ring together. Check your owner's manual or the sticker inside the driver's door jamb to confirm your engine size if you're unsure.
Tools and supplies you'll need
You'll need an oil filter socket or wrench to remove the housing cap. Ford sells a dedicated cartridge filter socket (part number 303-1312), but a 74 mm or 86 mm socket from a standard socket set works if you have the right size. The cap size depends on your engine — the 2.0L EcoBoost typically uses a 74 mm cap, while the naturally aspirated 2.0L uses an 86 mm cap. Using the wrong size risks cracking the plastic housing or stripping the threads.
You'll also need a drain pan (to catch old oil), a rag or paper towels, and the replacement filter element and O-ring. Some people use a filter wrench instead of a socket, but a socket gives you better leverage and is less likely to slip on the plastic cap. Have your new oil ready as well, since you'll be draining the old oil during this service.
Step-by-step removal and installation
Start by warming the engine for a minute or two to thin the oil, then turn it off and wait five minutes. This helps the oil drain faster and more completely. Locate the cartridge filter housing on top of the engine — it's the white or translucent plastic cylinder near the front. Place your drain pan underneath it.
Use your socket and ratchet to turn the housing cap counterclockwise. Turn slowly at first to break the seal, then unscrew it by hand once it's loose. The cap will come off with the old filter element still attached to it. Carefully pour any remaining oil into your drain pan, then pull the filter element out of the cap and discard it.
Inspect the inside of the housing for any debris or old rubber pieces. Wipe it clean with a rag. Remove the old rubber O-ring from the cap — it may stick, so use a plastic scraper or old credit card to pry it off without scratching the plastic. Install the new O-ring on the cap, making sure it sits evenly in the groove all the way around.
Insert the new filter element into the housing, pushing it down until it seats firmly. Screw the cap back on by hand first to avoid cross-threading, then use your socket to tighten it. The cap should be snug but not over-tightened — hand-tight plus a quarter turn with the socket is usually correct. Tighten too hard and you risk cracking the plastic housing.
Common mistakes that cause leaks
The most frequent problem after a cartridge filter change is a slow oil leak around the housing cap. This almost always happens because the old O-ring was reused instead of replaced. The rubber hardens and shrinks over time, so it no longer seals properly. Always install a fresh O-ring, even if the old one looks fine.
The second common mistake is over-tightening the cap. The plastic housing is not as strong as a metal filter canister, and excessive force can crack it or strip the threads. If you feel strong resistance while tightening, stop — you may have cross-threaded the cap. Back it out, check that the O-ring is seated correctly, and try again more slowly.
A third issue is forgetting to clean the inside of the housing before installing the new filter. Debris or bits of the old O-ring left inside can damage the new filter element or block oil flow. Take 30 seconds to wipe the housing clean with a dry rag.
When to replace the oil filter on your Focus
Ford recommends changing the oil and filter every 10,000 miles or 12 months, whichever comes first, for 2013 Focus models with the EcoBoost engine. The naturally aspirated 2.0L may have a longer interval — check your owner's manual or the maintenance schedule sticker in your door jamb. If you drive mostly short trips or in dusty conditions, consider changing it every 5,000 to 7,500 miles instead.
The filter should always be replaced at the same time as the oil. Reusing a filter from a previous oil change defeats the purpose of the service, since the filter has already trapped contaminants and will continue to restrict oil flow.
Frequently Asked Questions
Can I use a spin-on filter on my 2013 Focus instead of the cartridge?
No. The 2013 Focus is designed for a cartridge filter only. The housing and cap are engineered specifically for that design, and there is no spin-on adapter available from Ford or major aftermarket suppliers. Using the wrong filter type will not fit properly and could cause oil leaks or engine damage.
What happens if I over-tighten the housing cap?
Over-tightening can crack the plastic housing or strip the threads inside the cap. If you crack the housing, you'll need to replace the entire assembly, which costs significantly more than a filter element. If you strip the threads, the cap will spin freely without tightening and oil will leak out. Hand-tight plus a quarter turn is the correct torque.
How much oil does the 2013 Focus hold?
The 2013 Ford Focus holds approximately 4.5 to 5.7 quarts of oil, depending on engine type and whether you're doing a filter change only or a full drain and refill. Check your owner's manual for the exact capacity. Always check the dipstick after adding oil to confirm you're at the correct level.
Is the cartridge filter more expensive than a spin-on?
Cartridge filters are usually slightly cheaper than spin-on filters — typically $8 to $15 for the element and O-ring combined, compared to $12 to $20 for a spin-on. However, you also need the correct socket size to remove the cap, which may require a separate purchase if you don't already own one.
Can I reuse the old O-ring to save money?
No. The O-ring hardens and loses its elasticity after one oil change cycle, so it will not seal properly on the second use. A slow oil leak around the housing cap is almost always caused by reusing an old O-ring. The O-ring costs only $2 to $4, so replacing it is worth the small expense to avoid an oil leak.