The 2013 Elantra uses a cartridge-style oil filter mounted on top of the engine, not a spin-on canister underneath

The 2013 Hyundai Elantra has a cartridge oil filter—a cylindrical element that sits inside a plastic housing on the top of the engine, near the front. This is different from the spin-on filters you might be used to on other cars. The housing is white plastic with a large cap, and it's located on the driver's side of the engine bay, just behind the valve cover. You don't unscrew a whole filter; instead, you unscrew the cap, pull out the old filter element, and drop in a new one.

This design is actually simpler than it sounds once you know where to look. The cartridge filter costs less than a spin-on, and the whole job takes about 15 minutes if you're comfortable working on your own car. If you're paying a shop, the labor is usually quick, so the total cost stays low.

Key Takeaways

  • The 2013 Elantra's oil filter is a cartridge element inside a white plastic housing on top of the engine, not a spin-on filter underneath.
  • You need a filter wrench to unscrew the housing cap, and the correct replacement element for your engine size (1.6L or 2.0L models use the same filter).
  • Always replace the rubber O-ring seal on the housing cap when you change the filter, or it will leak oil.
  • The job takes about 15 minutes and requires an oil drain pan, a filter wrench, and the new filter element plus O-ring.

Locating the filter housing on your engine

Open your hood and look toward the front of the engine on the driver's side. You'll see a white plastic cylinder about 3 inches tall with a large cap on top—that's the filter housing. It sits just behind and to the left of the valve cover. On some 2013 models, you may need to remove the plastic engine cover first, but most have enough clearance to work around it.

The housing is bolted to the engine block, and the cap screws on from the top. A rubber O-ring sits between the cap and the housing body to seal in the oil. When you unscrew the cap, the old filter element comes out with it, still attached to the underside of the cap.

What you need to buy and have on hand

You need a cartridge oil filter element designed for the 2013 Elantra. Both the 1.6L and 2.0L engines use the same filter part number: Hyundai part 26300-35503 or an equivalent aftermarket cartridge filter. You also need a replacement O-ring seal—Hyundai part 26300-35504. These are inexpensive; the filter element usually costs $8 to $15, and the O-ring is $2 to $4.

You'll also need an oil drain pan (to catch old oil), a filter wrench (a large socket-style wrench that grips the housing cap), fresh engine oil, and a clean rag or paper towels. A filter wrench is essential—the cap is tight, and trying to unscrew it by hand usually fails and can damage the plastic housing.

The step-by-step replacement process

Start by warming the engine for a minute or two, then turn it off and wait five minutes. Warm oil drains faster and more completely. Place your oil drain pan under the filter housing (oil will spill when you unscrew the cap). Use the filter wrench to unscrew the housing cap by turning it counterclockwise. The cap will come off with the old filter element still attached to its underside.

Unscrew the old filter element from the cap by hand—it's threaded on. Discard the old element and the old O-ring. Wipe the inside of the cap and the top of the housing with a clean rag to remove any debris or old oil residue. Screw the new filter element onto the cap by hand until it's snug, then hand-tighten it another half-turn. Do not over-tighten; you'll strip the threads.

Install the new O-ring onto the cap. It should sit in the groove on the underside of the cap. Screw the cap back onto the housing by hand first to align it, then use the filter wrench to tighten it firmly—snug, not cranked down. The O-ring will compress as you tighten, and you'll feel resistance. Stop when you feel solid resistance; over-tightening can crack the plastic housing.

Start the engine and let it run for 30 seconds, then turn it off and wait two minutes. Check under the housing cap for leaks. If oil is dripping, the O-ring may not be seated correctly; unscrew the cap, check the O-ring position, and tighten again. Once the filter is find and not leaking, you're done with the filter itself. Don't forget to check and top up your engine oil level afterward.

Why the O-ring matters and what happens if you skip it

The rubber O-ring is what actually seals the housing cap to the body. If you reuse the old O-ring or forget to install a new one, oil will seep out around the cap, especially when the engine is running and oil pressure is high. A slow leak can go unnoticed until your oil level drops enough to trigger a warning light or cause engine damage.

Hyundai includes a new O-ring with most replacement filter cartridges, but always check your parts package. If it's not there, buy one separately—it costs almost nothing and takes 10 seconds to install. This is one of the most common mistakes people make on cartridge filters, and it's entirely preventable.

Common mistakes and how to avoid them

The biggest mistake is forgetting the O-ring or reusing the old one. The second is over-tightening the cap, which cracks the plastic housing and requires replacing the entire assembly. Hand-tighten first, then use the wrench to snug it down—you don't need to muscle it.

Another common error is not wiping out the inside of the housing before installing the new filter. Old oil residue and metal particles can contaminate the new filter element. Spend 30 seconds with a rag and you'll avoid that problem. Finally, don't forget to check your oil level after the job. The new filter holds a small amount of oil, so your level will be slightly lower than before the change.

When to replace the oil filter on your 2013 Elantra

Hyundai recommends changing the oil and filter every 10,000 miles or 12 months, whichever comes first, under normal driving conditions. If you drive in severe conditions—frequent short trips, towing, dusty roads, or extreme temperatures—change it every 5,000 miles or 6 months. Check your owner's manual for the exact interval that applies to your driving.

The filter should always be replaced whenever you change the engine oil. Never reuse an old filter or skip the filter change to save money. The filter removes contaminants from the oil, and a clogged or old filter reduces oil flow and defeats the purpose of an oil change.

Frequently Asked Questions

Can I use a spin-on filter instead of the cartridge filter?

No. The 2013 Elantra is designed for a cartridge filter, and the housing is not compatible with spin-on filters. Using the wrong filter type will not fit, and forcing it can damage the housing. Stick with the cartridge element designed for your model.

What if I over-tighten the cap and crack the plastic housing?

You'll need to replace the entire filter housing assembly, which costs more than the filter and O-ring combined. If the crack is small and not leaking, you might temporarily seal it with epoxy putty, but a replacement housing is the proper fix. This is why hand-tightening first, then using the wrench to snug it, matters.

Do I need to prime the new filter with oil before installing it?

No. Cartridge filters for the Elantra do not need to be pre-filled with oil. straightforward install the dry element, screw on the cap, and start the engine. The oil pump will fill the filter as the engine runs.

How do I know if the filter is leaking?

Start the engine and let it idle for 30 seconds. Turn it off and wait two minutes, then look under the housing cap for wet spots or drips. If you see oil, the O-ring is not seated correctly. Unscrew the cap, check that the O-ring is in the groove, and tighten the cap again.

Can I change the oil filter without draining the engine oil?

Yes. The cartridge filter can be changed independently of an oil change. However, it's more practical to change both at the same time since you're already under the hood and have the drain pan ready. If you're only changing the filter, place the drain pan underneath to catch the small amount of oil that spills when you unscrew the cap.