The 2014 CR-V uses a cartridge-style oil filter that sits on top of the engine

Your 2014 Honda CR-V does not have a spin-on oil filter like many other vehicles. Instead, it uses a cartridge filter—a cylindrical element that lives inside a plastic housing on the top of the engine. This matters because you cannot straightforward unscrew a canister; you have to open the housing, remove the old filter element, and install a new one. The housing itself stays in place.

The filter element part number for all 2014 CR-V models (both the 2.0-liter and 2.4-liter engines) is Honda 15400-PLM-A02 or the equivalent Acura part 15400-PLM-A01. You can also use OEM-equivalent filters from Fram, Mobil, or Castrol that are designed for this process—look for filters labeled as fitting a 2014 CR-V cartridge housing. The housing itself rarely needs replacement unless it cracks or the threads strip.

Key Takeaways

  • The 2014 CR-V has a cartridge-style filter on top of the engine, not a spin-on filter, so you must open the housing to access the element.
  • The correct Honda part number is 15400-PLM-A02, and the filter costs between $8 and $15 depending on the brand you choose.
  • You will need a cartridge filter wrench (usually $10 to $20) to remove the housing cap, or you can use a rubber strap wrench if you have one.
  • The job takes 10 to 15 minutes and requires only basic tools: a wrench, an oil drain pan, and a clean rag.
  • Replacing the filter every 10,000 miles or as recommended in your owner's manual keeps the engine clean and helps prevent sludge buildup.

What you need to buy and what tools to gather

Beyond the filter element itself, you will need a cartridge filter wrench—a socket-like tool that grips the housing cap so you can turn it without stripping the plastic. Honda cartridge filter wrenches are typically 74 mm or 86 mm in diameter; for the 2014 CR-V, you want the 74 mm size. These cost $10 to $20 new and are reusable. If you already own a rubber strap wrench, that will work too, though it requires more grip strength.

Gather an oil drain pan (to catch any spill), a clean rag or paper towels, and a socket wrench or adjustable wrench if you need to remove the drain plug. You do not have to drain the entire oil pan to change the filter—the cartridge housing holds only a small amount of oil—but some people prefer to do both jobs at once. If you are changing the oil as well, have your new oil ready and know the correct grade and capacity for your model (check your owner's manual or the inside of the fuel door).

Step-by-step filter replacement

Start with the engine cold or warm but not hot. Open the hood and locate the filter housing on top of the engine—it is a black plastic cylinder about 3 inches tall, usually toward the back of the engine bay. Place your oil drain pan underneath it to catch drips.

Fit your cartridge filter wrench onto the housing cap (the top of the cylinder) and turn it counterclockwise. The cap will come off with a small amount of oil still inside. Carefully pour that oil into your drain pan. You will see the old filter element sitting inside the housing—it looks like a white or yellow accordion-shaped cylinder. Lift it straight out and discard it.

Wipe the inside of the housing clean with a rag to remove any debris or old filter material. Check the rubber seal (O-ring) on the underside of the cap; if it looks cracked or flattened, replace it. Most replacement filters come with a new O-ring, but if yours does not, you can order one separately (Honda part 15412-PFB-000).

Install the new filter element by sliding it straight down into the housing. It will sit on a center post. Screw the cap back on by hand first, then use your wrench to tighten it. Do not over-tighten—snug is enough. The cap should be hand-tight plus a quarter turn with the wrench. Over-tightening can crack the plastic housing.

Why the cartridge design matters for your engine

The cartridge filter design is more compact than a spin-on and allows Honda to fit the filter closer to the engine block, which means oil reaches the filter faster after a cold start. This is a safety feature: cold oil is thicker, and getting it filtered quickly reduces wear on engine bearings during the first few seconds of running.

The trade-off is that you cannot see the filter element at a glance—you have to open the housing to know if it is clogged. This is why sticking to your maintenance schedule matters. A clogged filter forces oil to bypass the filter element and circulate unfiltered, which accelerates sludge buildup and shortens engine life. On a 2014 CR-V, Honda recommends changing the filter every 10,000 miles under normal driving, or every 5,000 miles if you drive in severe conditions (frequent short trips, towing, dusty roads, or extreme heat).

Common mistakes to avoid

The most common error is over-tightening the housing cap. The plastic threads are not as strong as metal, and cranking too hard will crack the housing and force you to replace the entire assembly—a $40 to $60 part. Hand-tight plus a quarter turn is the right amount of force.

Another mistake is forgetting to check or replace the O-ring seal on the cap. If the old seal is compressed or cracked, the new one will not seat properly and you may see a small oil leak around the cap. Most aftermarket filters include a new O-ring, but always check before you close it up.

Do not pour old filter oil down the drain or into the ground. Collect it in a container and take it to a recycling center, auto parts store, or quick-lube shop—most will take it for free. Many auto parts retailers (AutoZone, O'Reilly, NAPA) also accept used oil and filters at no charge.

When to replace the housing cap itself

The plastic housing cap rarely fails, but it can crack if you over-tighten it or if the engine gets very hot. If you see oil seeping around the cap threads even after you have tightened it and replaced the O-ring, the cap threads are probably stripped. You will need to replace the cap assembly, which costs $35 to $60 depending on the supplier.

To replace the cap, straightforward unscrew the old one and screw on the new one. Make sure the new cap comes with a fresh O-ring. If you are replacing the cap, this is also a good time to clean the inside of the housing again and inspect the center post for damage.

Frequently Asked Questions

Can I use any cartridge filter, or does it have to be Honda?

You can use any cartridge filter designed for a 2014 CR-V, including Fram, Mobil, Castrol, and other major brands. They must be the same size and thread pattern as the Honda original. Check the box to confirm it fits your model year and engine size. Honda OEM filters are often the most reliable choice, but quality aftermarket filters work well too.

How much oil comes out when I open the filter housing?

Usually about half a quart or less. That is why you do not need to drain the entire oil pan to change the filter. Have your drain pan ready, but expect only a small amount of spillage if you work carefully.

What if the housing cap is stuck and will not turn?

explore penetrating oil (like WD-40) around the cap threads and let it sit for 10 to 15 minutes. Then try again with your wrench. If it still will not budge, wrap a rubber strap around the cap for better grip. Do not force it hard enough to crack the plastic—if it will not move, stop and take the vehicle to a shop rather than risk breaking the housing.

Do I need to fill the new filter with oil before installing it?

No. Unlike spin-on filters, cartridge filters do not need to be pre-filled. straightforward install the dry element and screw the cap back on. The oil will flow through the filter once the engine starts.

How often should I check the filter between changes?

You cannot see the cartridge filter without opening the housing, so checking it is not practical. Instead, follow your maintenance schedule: every 10,000 miles under normal driving, or every 5,000 miles if you drive in severe conditions. If you notice the oil pressure light flickering at idle, that can signal a clogged filter, and you should change it when ready.