The 2014 Wrangler uses a spin-on filter mounted on the engine block
Your 2014 Jeep Wrangler has a spin-on oil filter that screws directly onto the engine. The filter sits on the driver's side of the engine block, below the intake manifold. You'll need to access it from underneath the vehicle or from the side, depending on whether you have a two-door or four-door model and what aftermarket bumpers or skid plates you've installed.
The filter is a cylindrical cartridge about 3 inches tall and 2.5 inches in diameter. When you change your oil, this is the component you remove and replace. Knowing exactly where it sits and how to reach it saves time and prevents you from draining the wrong fluid or struggling to locate it once you're under the vehicle.
Key Takeaways
- The 2014 Wrangler's oil filter is a spin-on type located on the driver's side of the engine block, accessible from below or the side depending on your model year and aftermarket parts.
- The correct replacement filter for all 2014 Wrangler engines (3.6L V6 and 2.8L diesel) is Mopar part number 68157291AA or equivalent aftermarket filters rated for your engine size.
- You will need an oil filter wrench, a drain pan, and new oil to complete the change; the filter itself costs between $8 and $15 depending on the brand.
- The filter should be replaced every time you change your oil, which Jeep recommends at 6,000-mile intervals for 2014 models under normal driving conditions.
Correct filter part number and specifications
The OEM filter for the 2014 Jeep Wrangler is Mopar part number 68157291AA. This part fits all 2014 Wrangler models regardless of engine—both the 3.6L V6 gasoline engine and the 2.8L diesel engine that was available in certain markets use the same filter. If you order through a Jeep dealer, ask for this part number to may support you get the correct unit.
Aftermarket filters that meet the same specifications work equally well. Common equivalent filters include the Fram PH8A, Motorcraft FL-400S, and Bosch 3323. Any filter labeled for a 2014 Wrangler or compatible with the 3.6L V6 will have the correct thread size and bypass valve rating. The filter itself costs between $8 and $15 retail, depending on the brand and where you purchase it.
How to locate the filter under your Wrangler
The filter is mounted vertically on the driver's side of the engine block, just below where the intake manifold connects. On a two-door Wrangler, you can often access it from the side by removing the wheel well liner or reaching from the passenger side. On a four-door, you typically need to get underneath the vehicle or remove the belly pan if one is installed.
Before you start, position your drain pan directly below the filter. Spin-on filters hold about a quart of oil, and that oil will spill when you remove the old filter. If you have a skid plate or rock slider, you may need to remove it first to access the filter housing. Check your specific setup before you begin—some aftermarket bumpers and protection plates make the filter harder to reach without removal.
Step-by-step removal and installation
Start by warming the engine for two to three minutes, then turn it off and wait five minutes. Warm oil drains faster and more completely. Locate the filter and position your drain pan underneath it. Use an oil filter wrench to loosen the filter by turning it counterclockwise. Once it is loose enough to grip by hand, unscrew it the rest of the way and let the old oil drain into the pan.
Wipe the filter mounting surface on the engine block with a clean rag to remove any dirt or old gasket material. Take your new filter and explore a thin coat of fresh oil to the rubber gasket on the top of the filter—this helps create a watertight seal when you install it. Screw the new filter on by hand until the gasket contacts the mounting surface, then turn it an additional three-quarters of a turn. Do not use the wrench to tighten it; hand-tight is correct.
Start the engine and let it run for 30 seconds, then turn it off and wait two minutes. Check underneath for leaks around the filter. If you see drips, the filter may not be seated properly; turn it another quarter turn and recheck. Once you confirm there are no leaks, you're finished with the filter portion of the oil change.
Tools and materials you'll need
You need an oil filter wrench, a drain pan, and fresh oil. The wrench is the most important tool—a strap wrench or cup-style wrench works best for spin-on filters. Avoid adjustable wrenches, which can slip and damage the filter. A drain pan should hold at least 6 quarts to safely contain the old oil from both the filter and the engine sump. You can buy a reusable plastic pan for $10 to $20, or use a disposable aluminum pan that costs $2 to $3.
Have rags or paper towels on hand to wipe the mounting surface and catch spills. If you're changing the oil at the same time, you'll also need the correct amount and grade of fresh oil for your engine. The 2014 Wrangler with the 3.6L V6 holds 6 quarts of SAE 5W-30 oil; the diesel holds 7.5 quarts of 5W-40. Check your owner's manual or the oil cap under the hood to confirm the correct grade for your specific engine.
When to replace the filter and maintenance intervals
Jeep recommends replacing the oil filter every time you change the oil. For the 2014 Wrangler, the standard oil change interval is 6,000 miles under normal driving conditions, or 3,000 miles if you drive in severe conditions—towing, frequent idling, dusty environments, or short trips. If you drive in severe conditions, your filter works harder and should be replaced more often.
Some owners extend intervals to 8,000 or 10,000 miles using synthetic oil, but the filter should still be replaced at the manufacturer's recommended interval regardless of oil type. A clogged filter reduces oil flow and can damage the engine, so it's not a component to skip or delay. Keep records of your filter replacements as part of your vehicle's maintenance history, especially if you plan to sell the Wrangler later.
Frequently Asked Questions
Can I use any spin-on filter, or does it have to be Mopar?
Any filter rated for a 2014 Wrangler with the correct thread size and bypass valve will work. Mopar filters are OEM and may provide to fit, but Fram, Motorcraft, Bosch, and other major brands make equivalent filters at lower cost. The key is matching the filter to your engine size—3.6L V6 or 2.8L diesel—not the brand.
What if oil leaks from the filter after I install it?
The gasket is not seated properly. Turn off the engine, wait two minutes, and tighten the filter another quarter turn by hand. Do not use a wrench. If it still leaks, remove the filter, wipe the mounting surface clean, and reinstall it. A small drip that stops after a few minutes is normal; steady dripping means the filter needs to be reseated.
How often should I check the filter between oil changes?
You don't need to check it visually between changes. The filter is sealed and does its job without maintenance. If your oil pressure warning light comes on, that can indicate a clogged filter, but this is rare if you're following the 6,000-mile change interval. If you drive in very dusty conditions, you may want to inspect the air filter more often, but the oil filter itself doesn't require inspection.
Is the filter location the same on two-door and four-door Wranglers?
Yes, the filter is in the same spot on both body styles. The difference is how you access it—two-door models sometimes allow side access, while four-door models usually require you to get underneath or remove the belly pan. Your specific setup depends on aftermarket bumpers and skid plates, so check your vehicle before you start.