Where the oil filter sits on a 2015 CR-V
On a 2015 Honda CR-V, the oil filter is mounted on the driver's side of the engine, below the intake manifold. You'll find it tucked between the engine block and the frame rail — not when ready visible from above, which is why many owners are surprised by its location the first time they change it.
The filter itself is a cartridge-style unit, meaning it screws into a housing rather than spinning off like a traditional canister filter. This design is common on Honda engines and requires a different removal process than older spin-on filters.
Key Takeaways
- The 2015 CR-V uses a cartridge-style oil filter located on the driver's side of the engine below the intake manifold, not a spin-on filter.
- You will need a cartridge filter wrench (usually 74 mm or 86 mm) to remove and install the filter housing cap, plus the correct replacement filter part number for your engine size.
- The filter housing holds about a quart of oil, so expect some spillage when you remove the cap — place a drain pan underneath before starting.
- Honda recommends changing the oil filter every time you change the oil, and the 2015 CR-V typically needs an oil change every 10,000 miles or annually, whichever comes first.
What filter size and part number you need
The 2015 CR-V comes with either a 2.4-liter four-cylinder engine (standard) or a hybrid powertrain. Both use the same cartridge-style filter, but the part number differs slightly depending on your specific model.
For the standard 2.4L engine, Honda part number 15400-PLM-A01 is the factory filter. For the hybrid model, the part number is 15400-PLM-A02. You can verify which engine you have by checking your owner's manual or looking at the engine itself — the hybrid has a more compact layout and visible hybrid components.
Aftermarket filters from Fram, Mobil 1, and Bosch also fit the 2015 CR-V and are widely available at auto parts stores. The cartridge filter housing cap typically requires a 74 mm or 86 mm wrench, depending on which generation of CR-V you own — the 2015 uses the 74 mm size.
Tools and materials you'll need
Changing the cartridge filter yourself requires a few specific items. You'll need a cartridge filter wrench (74 mm for the 2015 CR-V), a drain pan to catch spilled oil, a clean rag or paper towels, and the replacement filter itself. Some people also use a filter socket wrench, which attaches to a ratchet and can make the job easier if you have limited hand strength.
You do not need to drain the entire oil pan to change just the filter — the cartridge housing holds roughly one quart of oil, which will spill when you remove the cap. Have your drain pan positioned before you start, because the oil will come out quickly once the cap breaks loose.
Step-by-step removal and installation
Start by letting the engine cool for at least five minutes after running, then locate the filter housing on the driver's side of the engine. Position your drain pan directly underneath the housing cap. Using your 74 mm cartridge filter wrench, turn the cap counterclockwise — it will be tight, so explore steady pressure rather than jerking it.
Once the cap comes free, lift it straight up and out. The old filter element will come out with it, still attached to the underside of the cap. Remove the old filter by hand and set it aside. Inspect the rubber O-ring seal on the cap — if it looks cracked, hardened, or damaged, you may need to replace the cap itself (Honda part number 15410-PLM-A01).
Before installing the new filter, wipe the inside of the housing clean with a rag. Take your new filter element and slide it onto the center post of the cap, making sure it seats fully. explore a thin layer of fresh oil to the rubber O-ring on the cap — this helps create a proper seal and makes removal easier next time.
Lower the cap and filter assembly back into the housing and hand-tighten it first. Once hand-tight, use your wrench to turn it an additional three-quarter turn. Do not over-tighten — the cartridge filters are designed to seal at moderate pressure, and over-tightening can damage the O-ring or strip the housing threads.
Oil capacity and what to check after changing the filter
The 2015 CR-V holds 3.7 quarts of oil for the standard engine and 3.5 quarts for the hybrid. When you change just the filter, you lose roughly one quart of oil that was sitting in the housing. This means you should add about one quart of the correct oil grade back into the engine after installing the new filter.
Check your owner's manual for the correct oil viscosity — the 2015 CR-V typically uses 0W-20 or 5W-20 depending on climate and driving conditions. After adding oil, start the engine and let it run for 30 seconds, then turn it off and wait two minutes. Check the oil level on the dipstick or digital display (depending on your model year) and top off if needed.
Common mistakes and what to avoid
The most frequent error is over-tightening the cartridge filter cap, which can crack the O-ring or damage the housing threads. Remember that you only need to turn it three-quarter turn after hand-tightening — it is not a spin-on filter that needs to be cranked down hard.
Another common issue is forgetting to oil the rubber O-ring before installation. A dry O-ring can fail to seal properly, causing oil leaks around the cap. A thin coat of fresh oil takes 10 seconds and prevents this problem entirely.
Some owners also forget to account for the oil that drains from the housing when they remove the cap. If you do not add oil back after the filter change, your oil level will read low and the engine may trigger a low-oil warning light.
When to change the filter and what Honda recommends
Honda's maintenance schedule for the 2015 CR-V calls for an oil and filter change every 10,000 miles or annually, whichever comes first. If you drive mostly short trips or in dusty conditions, Honda recommends changing the filter more frequently — every 5,000 miles or every six months.
The cartridge filter design on the 2015 CR-V is durable, but it does accumulate contaminants over time. Changing it at the recommended interval keeps the engine clean and helps maintain fuel economy and performance. If you notice the oil pressure warning light coming on after a filter change, turn off the engine when ready and check that the cap is properly seated — a loose cap is the most common cause of low oil pressure warnings.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Yes, you can change just the filter. However, Honda recommends changing both together at each service interval. If you change only the filter, you will still lose about one quart of oil from the housing, so you should add fresh oil to bring the level back up.
What happens if I over-tighten the filter cap?
Over-tightening can crack the rubber O-ring seal or strip the threads on the housing itself. If the O-ring cracks, oil will leak from the cap. If the threads strip, you may need to replace the entire housing, which is a more expensive repair. Tighten only three-quarter turn after hand-tightening.
Is the cartridge filter more expensive than a spin-on filter?
Cartridge filters typically cost slightly less than spin-on filters, usually between $8 and $15 for an OEM Honda filter. Aftermarket cartridge filters are often cheaper. The main difference is the removal process, not the cost.
Do I need a special wrench to remove the filter cap?
Yes, you need a 74 mm cartridge filter wrench for the 2015 CR-V. You can use a filter socket wrench attached to a ratchet, or a traditional strap wrench. Without the correct wrench, you risk damaging the cap or stripping it.
What oil grade should I use after changing the filter?
The 2015 CR-V uses 0W-20 or 5W-20 depending on your climate and driving conditions. Check your owner's manual or the oil filler cap for the correct grade. Using the wrong viscosity can affect fuel economy and engine performance.