What oil filter your 2015 Altima needs and where to find it
Your 2015 Nissan Altima uses a Nissan OEM filter part number 15208-9E000 or an equivalent aftermarket filter rated for your engine size. The filter sits on the driver's side of the engine block, below the intake manifold — you'll need to get under the car or use a jack to reach it comfortably. Most auto parts stores stock this filter, and it costs between $8 and $15 depending on the brand and retailer.
The filter itself is a spin-on canister about 3 inches tall. When you order a replacement, confirm the part number matches your engine: the 2.5L four-cylinder (which is what most 2015 Altimas have) uses the 15208-9E000. If your Altima has the 3.5L V6 (less common but possible), the part number is different, so double-check before you buy.
Key Takeaways
- The 2015 Altima with a 2.5L engine uses Nissan part number 15208-9E000, which costs $8 to $15 and is available at most auto parts stores.
- The filter is located on the driver's side of the engine block below the intake manifold and requires you to work from underneath the vehicle.
- You will need an oil filter wrench, a drain pan, and new oil to complete the job — the filter alone is only part of an oil change.
- Changing the filter every 3,000 to 5,000 miles (or per your owner's manual) keeps contaminants out of your engine and prevents sludge buildup that damages bearings and seals.
How to locate and access the filter on your Altima
Start by warming up the engine for a minute or two — warm oil flows faster and drains more completely. Turn off the engine and let it cool for 2 to 3 minutes so you don't burn yourself. Raise the car on a jack or drive it onto ramps if you have them; you need enough clearance to slide underneath and work comfortably.
Look on the driver's side of the engine block, roughly midway down. The filter is a vertical canister with a hex nut on top (the part you grip with a wrench). You may see a splash shield or undertray between you and the filter — if so, unbolt it first. Once you can see the filter clearly, position your drain pan underneath it to catch the small amount of oil that will spill when you remove it.
Removing the old filter without making a mess
Use an oil filter wrench — a socket-like tool that grips the canister — to turn the filter counterclockwise. Start slowly; if the wrench slips, you've either got the wrong size or the filter is on too tight. Once it breaks loose, you can usually unscrew it by hand the rest of the way. Expect about a cup of old oil to drain into the pan as you pull the filter away from the engine.
Before you install the new filter, wipe the mounting surface on the engine block with a clean rag. Any old oil or debris left behind can prevent a good seal. Look at the rubber gasket (the ring around the top of the old filter) — if it stuck to the engine block instead of coming off with the filter, remove it by hand. A stuck gasket will prevent the new filter from sealing and cause a leak.
Installing the new filter correctly
Coat the rubber gasket on the new filter with a thin layer of fresh oil — use the new oil you're about to pour into the engine. This helps the gasket seat properly and makes removal easier next time. Screw the filter on by hand until the gasket touches the engine block, then turn it an additional three-quarters of a turn. Do not use the wrench to tighten it; hand-tight is correct. Over-tightening crushes the gasket and causes leaks.
Once the filter is installed, you're ready to refill the engine with fresh oil. The 2015 Altima with a 2.5L engine holds 3.7 quarts of oil; check your owner's manual if you have the V6. Pour the oil slowly and check the level with the dipstick after a few minutes of settling. Run the engine for 30 seconds, turn it off, wait a minute, and check the level again — it should be between the minimum and maximum marks on the stick.
Why the filter matters more than most owners realize
The oil filter traps particles — metal wear debris, carbon buildup, dust — that would otherwise circulate through your engine and damage bearings, piston rings, and valve seals. Over time, a clogged filter restricts oil flow, which forces the engine to bypass the filter entirely through a relief valve. When that happens, unfiltered oil circulates, and sludge begins to accumulate on critical surfaces.
Sludge buildup is silent and invisible until it's too late. It clogs oil passages, starves bearings of lubrication, and causes bearing wear that leads to engine knock, loss of power, and eventually catastrophic failure. A $12 filter changed on schedule costs you nothing compared to a $4,000 engine rebuild. The filter is the cheapest insurance your engine has.
Choosing between OEM and aftermarket filters
Nissan OEM filters (part number 15208-9E000) are made to Nissan's specifications and carry a warranty. They cost slightly more than many aftermarket options but are may provide to fit and perform correctly. If you're keeping your Altima long-term or want the certainty of an OEM part, this is the straightforward choice.
Aftermarket filters from brands like Fram, Mobil 1, Bosch, and Mann+Hummel are widely available and less expensive. Most are reliable, but quality varies — cheap filters with thin media can fail to trap fine particles effectively. Read reviews before buying an unfamiliar brand. Mid-range aftermarket filters ($10 to $12) usually offer better value than the cheapest options, and they perform nearly as well as OEM filters for most drivers.
When to change your Altima's oil filter
Nissan recommends changing the oil and filter every 3,000 miles for older Altimas or every 5,000 to 7,500 miles for newer models with synthetic oil. Check your owner's manual for the exact interval for your year and oil type — the manual is the authority on your specific car. If you drive in severe conditions (frequent short trips, dusty roads, towing), use the shorter interval.
Many owners change the filter every time they change the oil, which is the safest approach. Some people stretch the interval and change the filter every other oil change, but this defeats the purpose — a filter that's been working for 10,000 miles is already full of contaminants and losing effectiveness. Change it with every oil change and you'll never wonder whether it's still doing its job.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Technically yes, but it's not a good idea. When you remove the old filter, you lose about a cup of oil, so you'll need to top up anyway. More importantly, the filter and oil work together — old oil loses its detergent properties and ability to suspend contaminants, so a new filter in old oil is only half the job. Change them together.
What do I do with the old filter?
Most auto parts stores that sell filters will take your old one for free. Some recycling centers accept them. Never throw an oil filter in the trash — it contains residual oil and is considered hazardous waste in most places. If you can't return it to a store, call your local waste management facility to find a drop-off location.
Is the filter location the same on all 2015 Altimas?
Yes, all 2015 Altimas have the filter on the driver's side of the engine block in the same location. However, the part number differs between the 2.5L four-cylinder and the 3.5L V6, so confirm your engine size before ordering. Your VIN or owner's manual will tell you which engine you have.
What if the old filter won't come off?
If the filter is stuck, try tightening the wrench slightly and rocking it back and forth rather than turning it hard in one direction — this can break the seal without stripping the canister. If it's still stuck, wrap a rubber band around the wrench for better grip, or try a different size wrench. As a last resort, carefully punch a hole through the canister with a screwdriver and use that for leverage, but this is messy and should be a last option.
Do I need to reset anything after changing the filter?
No. The 2015 Altima does not have an oil filter warning light that needs resetting. Some models have an oil change reminder that you can reset through the instrument cluster menu, but this is separate from the filter itself and is optional — it's just a maintenance reminder, not a safety system.