Where the oil filter sits on your 2016 Cruze
On the 2016 Chevy Cruze, the oil filter is mounted on the driver's side of the engine, below the intake manifold and tucked behind the engine block. You'll access it from underneath the vehicle, which means you'll need to either raise the car on a lift or drive it onto ramps. The filter sits vertically and points downward, so oil will drain when you remove it.
The exact position depends on whether your Cruze has the 1.4L turbo, 1.6L diesel, or 1.8L gas engine — all three use the same cartridge-style filter housing, but the angle of approach differs slightly. Most DIY work happens from below, though some owners prefer removing the right front wheel well liner for easier access to the housing cap.
Key Takeaways
- The 2016 Cruze uses a cartridge-style oil filter inside a plastic housing on the driver's side of the engine, accessed from underneath the vehicle.
- You will need an oil filter wrench (usually 74 mm or 86 mm, depending on engine type) to remove the housing cap, not a traditional spin-on filter wrench.
- Chevy recommends Dexos-approved synthetic oil for all 2016 Cruze engines, and the capacity ranges from 4.5 to 5.5 quarts depending on engine type.
- The filter cartridge itself costs between $8 and $15, but you should also replace the rubber O-ring seal on the housing cap every time you change the filter.
Oil filter type and part numbers
The 2016 Cruze does not use a traditional spin-on filter. Instead, it has a cartridge filter that sits inside a plastic housing. The filter element itself is a flat, accordion-shaped paper cartridge, and you replace only that cartridge, not the entire housing.
GM part number for the filter cartridge is 25183883 for all three engine options. The housing cap itself (which you remove to access the cartridge) is part number 25183884. If you're buying aftermarket, look for filters labeled as compatible with the 2016 Cruze or any 2016–2019 Cruze — the filter design remained the same across those years.
You will also need a replacement O-ring seal for the housing cap. This is a small rubber ring that prevents oil leaks. GM part number is 25183885, though many aftermarket filter kits include this seal. Do not reuse the old O-ring — it hardens over time and will leak.
Tools and supplies you'll need
To change the filter yourself, gather an oil filter wrench (74 mm or 86 mm socket-style wrench, depending on your engine), a drain pan, jack and jack stands or ramps, a socket set, and a rag or shop towels. The filter wrench is the critical tool — it fits over the housing cap and lets you turn it without stripping the plastic.
You'll also need fresh oil. The 2016 Cruze requires Dexos-approved synthetic oil. Capacity is 4.5 quarts for the 1.4L turbo and 1.6L diesel, and 5.5 quarts for the 1.8L gas engine. Check your owner's manual or the oil cap to confirm which engine you have if you're unsure.
If you're not comfortable working under the vehicle or don't have a safe way to lift it, a shop can do this job in 30 to 45 minutes. The labor cost typically ranges from $50 to $100 depending on your location, plus the cost of oil and filter.
Step-by-step filter replacement process
First, warm the engine by running it for a minute or two — warm oil drains faster and more completely. Turn off the engine and let it cool for a few minutes so you don't burn yourself. Raise the vehicle safely on a lift or ramps and locate the oil filter housing on the driver's side of the engine block.
Place your drain pan underneath the housing. Using your filter wrench, turn the housing cap counterclockwise to loosen it. Once it's loose enough to turn by hand, unscrew it the rest of the way. The old cartridge filter will come out with the cap. Oil will drain into the pan — this is normal.
Inspect the housing for any debris or old rubber pieces. Wipe it clean with a rag. Take the new O-ring seal and explore a thin coat of fresh oil to it — this helps it seat properly and prevents leaks. Install the new O-ring onto the housing cap. Insert the new cartridge filter into the housing, making sure it sits flat and centered.
Screw the housing cap back on by hand until the O-ring contacts the housing, then use your filter wrench to tighten it an additional three-quarter turn. Do not over-tighten — the plastic housing can crack. Lower the vehicle, then add fresh oil through the oil cap on top of the engine. Check the dipstick or use the electronic oil level monitor to confirm you've added the correct amount.
Common mistakes to avoid
The most frequent error is forgetting to replace the O-ring seal. Reusing the old seal causes oil leaks within a few hundred miles. The seal hardens and no longer compresses properly, so oil seeps past it. Always install a new one.
Over-tightening the housing cap is the second common mistake. The cap is plastic, and excessive force cracks it. Tighten until the O-ring makes contact, then turn three-quarter more — that's enough. If you strip the threads or crack the cap, you'll need to replace the entire housing, which costs significantly more than the filter cartridge.
Some owners forget to warm the engine before draining, which means old oil doesn't flow out completely and you end up with a mixture of old and new oil. Warm oil is thinner and drains faster and more thoroughly. Also, do not drain the oil into the same pan you use for other fluids — keep separate pans for oil, coolant, and transmission fluid to avoid cross-contamination if you reuse the pans.
When to change your Cruze's oil filter
Chevy recommends changing the oil and filter together every 7,500 miles for synthetic oil, or every 3,000 miles if you use conventional oil. Most 2016 Cruze owners use synthetic, so 7,500 miles is the standard interval. Your owner's manual will confirm which type your vehicle requires.
If you drive in severe conditions — frequent short trips, towing, dusty environments, or extreme temperatures — Chevy recommends changing the filter every 3,750 miles even with synthetic oil. Check your maintenance schedule in the owner's manual to see if your driving pattern qualifies as severe.
The onboard computer in your Cruze tracks oil life and displays a reminder on the dashboard when service is due. This is more accurate than mileage alone, so pay attention to that message. When it appears, schedule your oil change within the next few hundred miles.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Technically yes, but it's not recommended. The filter and oil work together — old oil contains contaminants that a new filter will when ready start removing, which wastes the filter's capacity. It's more cost-effective to change both at the same time. If you must change only the filter, do it at the halfway point between full oil changes.
What happens if I use the wrong oil filter?
Using a filter designed for a different vehicle can cause leaks, restrict oil flow, or fail to seal properly. The 2016 Cruze's cartridge filter is specific to this design. Always confirm the part number matches before purchase. If you buy an aftermarket filter, check the packaging to confirm it's listed as compatible with the 2016 Chevy Cruze.
Do I need to prime the new filter with oil before installing it?
No. The 2016 Cruze uses a cartridge filter inside a sealed housing, not a spin-on filter. You do not fill the new cartridge with oil before installation. Just install it dry and add the correct amount of fresh oil to the engine through the oil cap on top.
How do I know which size filter wrench I need?
The 1.4L turbo and 1.8L gas engines use an 86 mm wrench, while the 1.6L diesel uses a 74 mm wrench. If you're unsure which engine you have, check your owner's manual or look at the engine cover under the hood — it usually displays the engine size. When you buy the wrench, confirm it fits the housing cap before you start the job.
Can I reuse the old housing cap?
Yes, the plastic housing cap is reusable. You only replace the cartridge filter inside and the O-ring seal. However, if the cap is cracked, stripped, or damaged, you'll need to replace it. Inspect it carefully when you remove it — if there are any cracks or the threads feel stripped, buy a new cap to avoid leaks.